Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Argh! Which would make the better shop space???

Featured Replies

Milo, if they are existing outlets what spencer said works well.  Other then that just cut and measure carefully the plate will cover up a little gap but you could be losing insulation values if you get to big of gaps, cold air can come through just make them as tight as you can.  If the holes are for new outlets you have yet to install then id suggest installing the boxes as well as any electrical wiring before putting the inside sheeting up.  Once you have the boxes in place most people i know just use a roto zip with a trim btt to punch a hole at approximately center of the electrical box (just make sure any wires are tucked in as far as they can go and that you dont have the bit set any deeper then the thickness of your material you are cutting) and then just run the bit to the edge of the box and follow it around.  That should get you real close if not an exact fit.  Then install any electrical devices like recepticales or switches.  Id suggest removing any existing electrical devices (you can just let them hang loose from the wires just make sure nothing touches anything else) and then cut your holes for the electrical boxes and then carefully pull the electrical devices through the hole in your sheeting and then slide the sheet back.  What you dont want to do is burry the dog ears on any existing devices already installed behind the new sheeting, youll have a heck of a time getting those out if you ever need to replace something like an outlet.  You can really use any method that works for you, ive even seen sheetrockers just start screwing drywall up and then go back and find the hump of the outlet and smash the center with a hammer and then cut it out clean.  I dont suggest that way but you get the idea its not rocket science, just be mindfull of the wiring so you dont damage it and be mindfull of burrying anything.

 

As for the subpanel and the ground.  You will need an additional bar, the panel should have came with one already.  Newer NEC code requires that the neutrals and grounds be seperated inside a subpanel.  So you will need one bar for grounds and one bar for neutrals as i stated above.  The name of them is grounding bar if thats not turning up a search answer i am not sure.  Id try eaither electrical grounding bar , or grounding bar. (EDITED TO ADD LINK http://www.homedepot.com/webapp/catalog/servlet/Search?storeId=10051&langId=-1&catalogId=10053&keyword=grounding+bar&Ns=None&Ntpr=1&Ntpc=1&selectedCatgry=Search+All )They are pretty generic and are usually interchangeable from manufacturer to manufacturer. its just a metal bar with holes and set screws that mounts to the inside of the panel were you will terminate the wires appropriately.  You have a similiar set up inside your main panel where all your neutrals and grounds go.

 

To answer your question about the grounding.  The main panel is providing the grounding system and the grounded system for the sub-panel,  this is why you need to run 4 wires instead of 3 (2 powers, 1 neutral, and 1 ground).  If you ran a 3 wire system (2 powers, 1 neutral) youd have to pick up the equipment ground through the neutral which is not legally upto code anymore.  So you need to run 4 wires, seperate your neutrals and grounds inside the sub panel into thier own grounding bars, and then youll need to install a secondary grounding electrode system  (ground rods) as I detailed in one of my earlier posts.

 

 

Hope that helps clear anything up as well as anwsers your question.

 

 

 

Nyles

 

 

  • Replies 71
  • Views 15.8k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Spencer_J
    Spencer_J

    after viewing the pictures, i recommend consolidating your cardboard & boxes. It's hard to see through the mess when you first move but it makes a huge difference when you condense things and orga

  • It was a dream shop idea, I was more supporting the idea. Circuits can be overloaded to the place where you are "browning" out tools further down the line. I may never draw 100amps but being able to a

Posted Images

  • Author

Hi All,

 

Sorry no pics, but I wanted to let everyone know that the shop is 98% done on the exterior!  Put on the shingles today.  All that's left for the basic shop is to trim the shingle on the edge of the roof, install one window, and a little trim around the window and one side.

 

After that it's run the eletrical, insulation, walls, and hopefully I'll be moved in in a week or so. 

 

More later!  Pics tomorrow.

  • 2 weeks later...
  • Author

Hey All,

 

My shop is done!  Well, Almost. :D

 

Seriously though, the shop itself is complete.  I am in the process of installing the electrical and insulation.  As always, work is getting in the way.  Another BIG plus is my Mom of all people found me an electrician who is helping me.  Go Mom!   This weekend is kind shot with my youngest daughter's 6th birthday, but I figure that's worth spending some time on.  Then Disney in two weeks, the Riding into History motorcycle rally in Jax, so it's starting to drift into June to finish. Ugh! :o

 

Here's a picture.  More later!

post-10429-0-87794300-1367071023_thumb.j

  • 4 weeks later...
  • Author

UPDATE!!

 

Well, work FINALLY gave me enough time to work some more on the workshop.

 

These picture will really show how SMMMAAAALLLLL it's going to be.  It'll be a HUGE change, and I'll be building storage solutions more than anything else for the first couple months, without a doubt.

 

But I have electricity! Finally!  Next is the insulation and interior walls, and I'll be set.  I hope!

 

Pictures!

 

 

post-10429-0-53779700-1369522794_thumb.j

post-10429-0-82888300-1369522816_thumb.j

post-10429-0-58629800-1369522820_thumb.j

post-10429-0-99671300-1369522823_thumb.j

I would figure out a way to add an air filter to that window air conditioner before you clog it up with dust. I open up my shop fans at least a couple of times a year and clean the blades, blow out the motor and lube the bearings. Dust and overspray will kill a fan or blower motor pretty quickly.

  • Author

I would figure out a way to add an air filter to that window air conditioner before you clog it up with dust. I open up my shop fans at least a couple of times a year and clean the blades, blow out the motor and lube the bearings. Dust and overspray will kill a fan or blower motor pretty quickly.

 

Ah, that is an EXCELLENT suggestion, Steve!  I could probably build a frame to slide a filter into and out of the A/C.  I am hoping that adding insulation to the walls and ceiling is going to help that little unit work well for my situation.

These picture will really show how SMMMAAAALLLLL it's going to be.

Since I'm way too lazy to dig back through the thread, what are the dimensions?

Regardless, I'm insanely jealous. I have really come to the conclusion that a small, dedicated space is better than a larger, shared space. I have a small slice of a small 2-car garage. (About 13x15) I have to spend too much time moving tools into place to start working and then time putting it all away. Would be nice to put tools in set places, run DC ductwork, have outlets where needed, etc.

Enjoy the space. You'll get it exactly the way you want it.

  • Author

Since I'm way too lazy to dig back through the thread, what are the dimensions?

Regardless, I'm insanely jealous. I have really come to the conclusion that a small, dedicated space is better than a larger, shared space. I have a small slice of a small 2-car garage. (About 13x15) I have to spend too much time moving tools into place to start working and then time putting it all away. Would be nice to put tools in set places, run DC ductwork, have outlets where needed, etc.

Enjoy the space. You'll get it exactly the way you want it.

Hey Bob, it's 16x10, with and additional 80 sqft of storage in two lofts. So 240sqft total.

Got the insulation and walls to install. Hoping to do a lot of it today. Going to get a couple hours in before it heats up!

Milo

Hey Bob, it's 16x10, with and additional 80 sqft of storage in two lofts. So 240sqft total.

Got the insulation and walls to install. Hoping to do a lot of it today. Going to get a couple hours in before it heats up!

Milo

 

Nice. The additional storage will be nice. It would be hard to store sheet goods up there (tough to get them up and down) but board storage could work. Plus places to put all of those things you don't use often, but don't want to get rid of. I'll be following along on your progress as you finish up.

  • Author

Nice. The additional storage will be nice. It would be hard to store sheet goods up there (tough to get them up and down) but board storage could work. Plus places to put all of those things you don't use often, but don't want to get rid of. I'll be following along on your progress as you finish up.

I was putting up the insulatin in the ceiling today, and it almost killed me, it was so HOT. I was hoping to finish, but not way. Now work beckons. :(

More later...

Insulation is one of those jobs your itching to be done with :P

  • Author

Insulation is one of those jobs your itching to be done with :P

Hot as hades! Didn't get finished!

I started to insulate the attic at my father in law's century home.  I barely got a quarter of it up before I couldn't stand the heat any more.  (That was merely a few minutes before I spotted the hornets nest... and being allergic to them, I figured it would be a good idea to not disturb them any more.)

  • Author

I started to insulate the attic at my father in law's century home.  I barely got a quarter of it up before I couldn't stand the heat any more.  (That was merely a few minutes before I spotted the hornets nest... and being allergic to them, I figured it would be a good idea to not disturb them any more.)

 

My daughter, who hornets seem to have a love affair with, read this post and ran off... ;)

 

Maybe it's time to get some more help on this project... ugh, I am never gonna get finished...!  :blink:

  • 1 month later...
  • Author

Almost Final Update!

I hope all the fine folks from this forum who have helped me out with excellent advice and info see this.  While the horrible weather has kept me from moving all my tools to the shop, the shop itself IS FINISHED!  Here are a few final pictures...

 

post-10429-0-71277500-1375029711_thumb.j  post-10429-0-23968100-1375029718_thumb.j  post-10429-0-85178100-1375029723_thumb.j

 

A few "just before the finish" shots.

 

post-10429-0-80683600-1375029769_thumb.j  post-10429-0-47178700-1375029781_thumb.j  post-10429-0-17183200-1375029777_thumb.j

 

post-10429-0-65503100-1375029786_thumb.j  post-10429-0-42283700-1375029794_thumb.j

 

And this is how it is now.  Carpentry by yourself is HARD.  The walls show it. The CEILING really show it! ACK!  BUT it's done, the insulation is done, walls are up, electricity is flowing, and now I just want to get the tools in there and cut some wood!

 

Thanks everyone!

Milo

  • Author

Free standing? 

 

Got the Uni, jointer, and Shopsmith moved in today!  Whew!  Weighed a TON! :)

The 220 breaker will fit if you have 2 slots open in your box (not really accounting for the actual current load, but if you're not firing everything up at once, you should be fine.)

 

Basically a 220 outlet just runs two hot 110v lines to the machine and shares a ground coming back to the box.

  • 4 weeks later...

Milo,

  Shop looks fantastic.  Sorry it took me so long to drop by.  I wrote you a PM as well.  Congrats again and looks good. 

 

 

 

Nyles

  • Author

Thanks Nyles.  It's crammed full of crap..uh..I mean woodworking stuff right now, but I HAVE made sawdust AND screwed up some cuts, so I think that makes it an official, right?

 

:)

 

On a serious note, Friday I plan of installing the Uni, so as you can imagine, I'm kinda geeked about that.  I'll have the new irons for the fence, and hope to fire that bad boy up for the first time in over a year!  Can't wait!

Milo

I HAVE made sawdust AND screwed up some cuts, so I think that makes it an official, right?

 

 

The way I work, the first time you have to toss a board because you screwed it up royally, it's officially a shop.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.