Chuck Melton Posted March 28, 2013 Report Posted March 28, 2013 I am complete novice to wood working and just getting my shop put together and I have a few bucks left in the slush fund I set up to buy some used tools to get myself started. I have the opportunity to buy a 6" craftsman jointer that looks to be 10ish years old for $60. Is it worth picking up so that I can have the tool, or is it going to be a $60 paperweight that I will be instantly frustrated with? I am also planning on taking a look at some very old power tools that my uncle has (they were originally my great grandfather's) and I believe he said there is a jointer amongst them. Would a jointer made in the 1930s or 1940s be preferable? Thanks in advance for any insight you can provide Quote
STL Woodguy Posted March 28, 2013 Report Posted March 28, 2013 Most hardwoods I get from the area are more often than not between 6-8 inches, so that's something to consider in terms of going for an 8" jointer instead. I think the only frustration on a 6" (aside from initially tuning any jointer) will be having to rip things down to fit it, resulting in more glueups. Depends on what you're working on, though. That said however, if it's in great condition and works fine, I totally would pay $60 for a decent 6" jointer. Should definitely get you started and if you find you don't need the extra two inches, great. But if you find you do, then you're not out much. Quote
Nyles Posted March 28, 2013 Report Posted March 28, 2013 Chuck, I too am on the search for that magic deal on a good used jointer. I can say that most of the craftsman 6" jointers ive been seeing on craigs list (and theres quite a few) have been going from 100-350$ with about 225-250$ being the median. If nothing else if the things in decent shape and works half way decent you could almost certainly I think get your cash back or maybe even turn a small profit if you unloaded it in the near future. I am sure these prices vary from area to area but hope that gives you some sort of idea what they are worth or going for. From my research a 8" would be the way to go but it seems they are alot rarer to find used and usually command more money even used. Id pry settle for the inexpensive 6" use it for a while see if it meets your needs and then unload it if it does not. I personally am 99.9% certain ill be ending up with a 6" jointer. You may also want to keep electrical needs in mind, most of the 8" jointers that ive seen seem to be 220v most of the 6" like the craftsman are 110v. If the power requirments are an issue that could help make up your mind. You dont say where the craftsman jointer is coming from but my biggest concern would be the condtion of the fence and the bed as well as the knives. Ask the gentleman for a test drive if he fires it up and straightens a piece of wood your good to go more than likely, if he starts making excuses you very well may want to walk away. Dont forget to bring a piece of wood incase he doesnt have one and your square so you can check out the condition of the unit. Sounds like a smoking deal though to me and id pry jump on it for that price can you really get hurt? Nyles Quote
G S Haydon Posted March 28, 2013 Report Posted March 28, 2013 Chuck, $60 Jointer sounds like good value, I think it would be worth a shot. The old jointer could work out fine however it is less likely to have all the safety boxes ticked and may need lots of tuning to get right. Quote
tim0625 Posted March 29, 2013 Report Posted March 29, 2013 I have the same 6" jointer. It's decent and for a hobbyist, it's probably OK. $60 is an excellent price. I've seen some in the $100-150 range also on Craig's list. It is 110V and I'm with Nyles...take some wood and test drive....be sure there's not another reason for the low price. New everything is available for it at Sears Parts Direct. Mine was a little different situation...it belonged to my deceased father in law so I wanted to restore it. Problem was, after he died, the shop caught fire; so since the jointer had been through that, I installed new bearings and knives. I stripped a bolt in the cutter head but found a new head on ebay for $5! The beds are a little cantankerous to tune; but otherwise its fine. Quote
Chuck Melton Posted March 31, 2013 Author Report Posted March 31, 2013 The jointer ended up not having knives in it, so I got it for $40. The motor sounds great and the surface rust doesn't look bad at all. Just had to make a sears parts order last week for a new router collet, looks like I am ordering some knives this week. Quote
Chuck Melton Posted April 1, 2013 Author Report Posted April 1, 2013 I hit a snag with the jointer. The clamps that hold the knives in place are missing and unavailable from sears. How special are these clamps? Would it be feasible to cut a piece of steel and drill holes in it to replace them? Quote
pghmyn Posted April 1, 2013 Report Posted April 1, 2013 I would say its feasible. From what I can tell on my jointer, it's just a steel bar with several tapped holes with bolts. Quote
wdwerker Posted April 1, 2013 Report Posted April 1, 2013 Those clamps are called " Gibs". You might be able to get some from a saw sharpening shop or other aftermarket source. Is the opening for the knives larger at the bottom than the top? Kind of triangular ? Quote
jmaichel Posted April 1, 2013 Report Posted April 1, 2013 I would just skip the jointer and wait for another deal, it sounds like this could just be hassle and keeps you from actually doing any woodwork. Quote
Chuck Melton Posted April 3, 2013 Author Report Posted April 3, 2013 I actually scored a much nicer Jointer pretty cheap. It had a "bad" motor that really just needs a capacitor. So instead of the benchtop model for with no gibs for $40 I am ending up with a freestanding 6 1/8" for $60 that is a foot longer. Quote
Chuck Melton Posted April 5, 2013 Author Report Posted April 5, 2013 Replaced the capacitor in the motor and it hummed to life. It seemed almost too easy... Well, it was too easy until I dropped the motor about 12" when trying to mount it and bound it up somehow. A quick disassembly and reassembly with the aid of a rubber mallet and it was back in action. I fired it up and ran a test piece of pine through. I definitely need to clean the tables up but it seemed to be fairly square. I am going to read up on jointer care and maintenance tonight so I can get it ready to actually use. Pic of my $50 (including parts) score is attached. Thanks for all the advice guys. The blades I ordered for the other benchtop missing the gibs came in today, it would cost almost as much to send them back to Sears as I paid for them, so I am tempted to try to either fabricate some gibs out of thin bar stock or put some more effort into trying to find some. Quote
Eric. Posted April 5, 2013 Report Posted April 5, 2013 I am tempted to try to either fabricate some gibs out of thin bar stock Be careful man. You don't want those knives flying off the cutterhead and into your hands or face. Unless you're a machinist, I'd nudge you in the "buy the gibs" direction. Quote
Chuck Melton Posted April 5, 2013 Author Report Posted April 5, 2013 Eric, You're probably right. I basically just want to get ride of the other jointer as I can imagine a use for it, and passing a jury rigged tool along just wouldn't be right ( I am flashing back to having a collet from a used router break on me and shoot a bit across the garage) I struck out completely on finding the gibs. The small jointer was manufactured for Craftsman by American Machine and Tool which went out of business shortly after. Quote
jHop Posted April 8, 2013 Report Posted April 8, 2013 You could always scrounge Craigslist for another 6" Craftsman that has the knife head... and swap parts. Then sell the cannibalized one for scrap... With what you've paid so far, you've got a little room to go before you've overpaid. (I'd start by looking for ones with rust or questionable square. If they just want to get rid of it, that's probably the one you want to take a second look at.) Quote
Chuck Melton Posted April 8, 2013 Author Report Posted April 8, 2013 I might see if someone just wants to pay the $40 I originally paid for and then they can have a pack of el cheapo sears jointer knives. All in all for what I shelled out for both of the jointers I would call it a good deal on the working one. Now I just need to score a planer... Quote
Chuck Melton Posted April 12, 2013 Author Report Posted April 12, 2013 I spent a bit of time getting the jointer cleaned up, waxed the tables and so on before starting to do some test jointing with it. My test jointing leads me to believe that my technique for using the machine may be a little off. I started off with some very even and fairly cleanly cut pieces of wood front the table saw.madter a few passes I was ending up with one end thicker than the other. Unless my jointer tables are horribly our of alignment, I am guessing the issue is the operator. Anyone have any good jointer usage resources? Quote
pghmyn Posted April 12, 2013 Report Posted April 12, 2013 I spent a bit of time getting the jointer cleaned up, waxed the tables and so on before starting to do some test jointing with it. My test jointing leads me to believe that my technique for using the machine may be a little off. I started off with some very even and fairly cleanly cut pieces of wood front the table saw.madter a few passes I was ending up with one end thicker than the other. Unless my jointer tables are horribly our of alignment, I am guessing the issue is the operator. Anyone have any good jointer usage resources? The video I learned my entire process from is Marc's "The Jointer is Jumpin" Everything you need to know about the jointer and lumber is in that video. Do you have a long straight edge or winding sticks? Quote
tim0625 Posted April 12, 2013 Report Posted April 12, 2013 Chuck, I'm with Eric...those knives spin extremely fast and I have to believe there is a lot of engineering in the design of the Gibs. Think of worst the case....a very sharp knife flies off at speed. It would cut a hand completely off! It could go THROUGH you. $60 is not worth that. Solution - scour Ebay. I told you, I found another cutter head for $5. Even if you don't find one now, it will be there eventually. Quote
Chuck Melton Posted April 13, 2013 Author Report Posted April 13, 2013 I think my technique issue was that I was focussing the pressure on the infeed table. Quote
tim0625 Posted April 13, 2013 Report Posted April 13, 2013 Sorry Chuck...I was running behind on the Gibs issue. Quote
Chuck Melton Posted April 13, 2013 Author Report Posted April 13, 2013 Yeah, the gibless jointer is probably just destined for the scrap heap as I am too lazy to try and sell it. I was thinking about whether I could repurpose the motor for a disc or spindle sander but I probably don't need another project. Quote
bobcrosley Posted April 13, 2013 Report Posted April 13, 2013 I'd still pull the motor anyway before you scrap the jointer. Doesn't take up much space to store, and you never know when you might find a problem that can be solved by a working motor. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.