Tom King Posted June 25, 2013 Report Posted June 25, 2013 Thanks for that link. I glanced through it. I've developed a much simpler system to follow since I bought an old vise that tilts. With a vise that tilts, you can do any slope angle,but the only way you ever have to hold the file is level. I sharpened them for a long time with an old vise that didn't tilt, but the way I'm doing it now seems simple in comparison, and much more intuitive to set up. I'll do some sort of video, and maybe an article when I get caught up. Quote
jhl.verona Posted June 25, 2013 Report Posted June 25, 2013 Only 11 minuets in so far but I've watched about 45 minutes to date. Didn't see any dancing, which was a little disappointing, but very informative indeed. Thanks for letting us know G.S. Thanks for that link. I glanced through it. I've developed a much simpler system to follow since I bought an old vise that tilts. With a vise that tilts, you can do any fleam angle,but the only way you ever have to hold the file is level. I sharpened them for a long time with an old vise that didn't tilt, but the way I'm doing it now seems simple in comparison, and much more intuitive to set up. I'll do some sort of video, and maybe an article when I get caught up. Look forward to this video, Tom. I like simple systems! John Quote
Eric. Posted June 25, 2013 Report Posted June 25, 2013 I should make a video of me packing up my saws and writing Lie-Nielsen's address on the box. It would only take about 30 seconds to watch. 1 Quote
Tom King Posted June 25, 2013 Report Posted June 25, 2013 There are always saw vises on ebay. Do a search for "saw vise", and there are a bunch on there right now. I like the ones with two levers-one for the saw clamp, and the other for tilt. I used a Wentworth that didn't tilt for a long time, but I wouldn't advise buying one that doesn't tilt. http://www.ebay.com/itm/CAST-HAND-SAW-SHARPENING-VISE-CLAMP-TOOL-/171063800852?pt=LH_DefaultDomain_0&hash=item27d4327414 I like to sit down while I'm filing, so a short jaw, and lever to operate it works just fine. When I first started, I thought I wanted one that held the whole saw, but a short one that's easy to reposition is just fine. I used to send my saws off for sharpening too, until they all came back botched up once. It's one of those things that's really easy, once you learn how, and have a simple system. If you don't use handsaws much, they don't need sharpening that often. Even as much as I use them, it's probably been a couple of years since I sharpened one, but I have a lot to choose from. Just like a really sharp chisel, or plane iron, once you use one that is truly sharp, you'll appreciate the difference of extreme sharpness, and all the right angles for the purpose. Quote
Trip Posted June 25, 2013 Report Posted June 25, 2013 ==> I should make a video of me packing up my saws and writing Lie-Nielsen's address on the box. It would only take about 30 seconds to watch. +1 yea, no kidding. LN does a great job... I get the saws back cleaned-up, sharpened and ready for action... Quote
G S Haydon Posted June 25, 2013 Author Report Posted June 25, 2013 I've watched about 45 minutes to date. Didn't see any dancing, which was a little disappointing, but very informative indeed. Thanks for letting us know G.S. Look forward to this video, Tom. I like simple systems! John John thanks, I genuinely laughed to myself for a couple of minutes Quote
Tom King Posted June 26, 2013 Report Posted June 26, 2013 Here's the way I do it in a nutshell: The vise is angled to the slope you want-softer wood more slope. I have strips of plywood I lay behind the vise with lines drawn on them that are the fleam I want-even a 0 one for some rip saws. The lines are spaced an inch or so apart. As you are filing, holding the file a degree off being in line with the drawn lines really shows up, so it's an easy reference to holding the right fleam angle. I make little handles for the outter end of the file like a lot of other people do, but I drill the hole at the fleam angle. Rake angle is drawn on the face of that little "handle/rake gauge". I make a bunch of these at one time, and they go in the Saw Sharp toolbox. I cut an angle block on the miter saw to go under the little blocks, so I can drill the right angled holes on the drill press. Just like the way I file a chainsaw chain, I like to start the cut with the smooth part at the end of the file in the gullet. Never back up with a file-it'll dull much faster. Lift and repeat. You can look in someone's toolbox and see how much they understand tools. If they have screwdrivers only for driving screws, and files are wrapped and not just thrown in with everything else, this is someone who has a chance. Joint the saw like everyone else does, clamp the saw in the vise, and with the visual references in place, it only takes a few minutes to file one side, change the little handle to one with the hole angled the other way, and go back down the other side of the saw. File each tooth on the first side you do halfway across the flat of the jointed top. Magnifying lenses help a lot for someone who is not naturally a little near-sighted. I use 42x saw sets, with little boxwood inserts so no metal rests on the sharp teeth. You need 2 saw sets. One for small backsaws, and one for handsaws. You have to taper the little pusher for backsaws. The 42x has a little plunger that grabs the saw before the anvils touch the teeth, so it's a lot less of a balancing act. There is even a guy on ebay that sells replacement springs for the 42x. They're the hardest to find, and most expensive to buy, but well worth what it takes to get one or two. Digital micrometers are cheap enough these days that everyone should have a couple of varieties. You can easily measure the amount of set you have and see how different amounts of set work. Get an old beater saw or two to learn how to do this on. Everyone screws up a bunch to start with, before the necessary skill comes. Once you understand it, it's easy and quick. It took a while to get this stuff all together, but not THAT long. It makes it easy to play with an old saw to see exactly how I want to file a good saw. Working on old houses, the vast majority of stuff I cut to fit something else-like every corner end of every piece of siding-is not only not square, but different than a lot of the others. I mark the corner end cuts with a preacher, and cut it with a handsaw. I might use anything from White Oak to clear Cypress for siding, and having a saw set just right for the material makes not only a better job, but is so much easier to work with. Now that I have all the stuff in the toolbox, I can sharpen a saw in less time than I can go to the Post Office. Now, I'm not saying this is the best way to go if you are just going to make a few pieces of furniture a year, but for someone who depends on handsaws a lot, this is a good thing to know how to do. Quote
TRBaker Posted June 27, 2013 Report Posted June 27, 2013 Good link, GS. Thanks. I've only watched forty minutes so far, but learned a lot. Unfortunately, this time of the day, it doesn't take much to put me to sleep. Quote
EdgewaterWW Posted June 27, 2013 Report Posted June 27, 2013 GS, looks great! if I was into that kind of thing (haha). I think I'm going to stay on the power tool side of woodworking. But all joking aside it was a great video. Tom, " in a nutshell"? Quote
Tom King Posted June 28, 2013 Report Posted June 28, 2013 GS, looks great! if I was into that kind of thing (haha). I think I'm going to stay on the power tool side of woodworking. But all joking aside it was a great video. Tom, " in a nutshell"? Takes longer to talk about it, than do it. Quote
G S Haydon Posted June 28, 2013 Author Report Posted June 28, 2013 Good link, GS. Thanks. I've only watched forty minutes so far, but learned a lot. Unfortunately, this time of the day, it doesn't take much to put me to sleep. TRB, I know that feeling. I often see a great history show or the like and think, wow that looks great. I'm always asleep within 5 to 10 mins Gotta hand it to the guy. All done for free and so comprehensive, I would imagine content like that might normally be offered for $15 or so. "GS, looks great! if I was into that kind of thing (haha). I think I'm going to stay on the power tool side of woodworking. But all joking aside it was a great video". Doug one of these eliminates the need for any of that, now they really are scary sharp! Quote
EdgewaterWW Posted June 29, 2013 Report Posted June 29, 2013 Thanks GS, I have one like that size, it looks good hanging on the wall, I like My saw to have a power switch. haha 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.