Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Squaring miter gauge to miter slot without trial and error

Featured Replies

I've seen the "cut 6 pieces at 30 degrees to amplify the error" method of determining whether or not your miter gauge is aligned correctly. However, it seems like there should be a better way. If I drop a speed square down into the miter slot, of course the square face that is sitting on the table cannot reach the miter gauge fence because it runs into the miter bar (see the attached miter.jpg).

 

It seems like there should be a way to overcome this problem - perhaps attaching (how?) a piece of wood to the miter bar, running it through the blade (giving you an edge that is parallel to the miter slot but above the surface of the table), then using that edge to square the gauge to the slot (see attached align.jpg). Of course you have to move the fence of the gauge over past the blade as shown in the picture.

 

Does anyone use a procedure like this? Perhaps it would require a second miter bar that has some mounting holes already drilled? (http://www.incra.com/images/buildit_mitersliderse_pic1_zoom.jpg) It just seems strange to me that there is not a good way to do it without making 12 cuts, guessing at an adjustment, making 12 more cuts... ad nauseum.

 

David

post-13877-0-97093700-1386527397_thumb.j

post-13877-0-99159300-1386527794_thumb.j

I just use a framing square (tested for dead on square of course) and put the long leg along a miter slot.  I've found it to be even more accurate than using the little digital magnetic cube method.

  • Author

Tom,

 

How do you use a magnetic cube to set the miter gauge fence? I thought it could only do vertical angles (like the blade bevel angle)?

 

My concern with putting the framing square along the miter slot is that since there are no physical stops, I can't believe I could get it to within .1 degree of square just by eye.

framing square +1 I square off the blade not the miter slot.

Miter slot is, of course, already calibrated dead on with a calibration plate on the saw arbor to miter slot.  With the slot, you get a lot more length to play with on the 24" leg of the square.

 

Zero cube on table saw wing.  Set miter gauge on table wing where cube was, letting slot bar hang down.  Set hang down to 90 degrees.  That'll get you to within 1/10 of a degree, but you can feel less than that with the framing square method.

Weird things happened when I tried to edit my last post.  A 1/10 of a degree is more than it might sound like. If I did the math right, 1/10 of a degree on a 24" radius, as with the framing square, is .042 inches.  A business card is .015 thick, and a piece of paper typically .003.

 

 Even with setting the blade to dead square, an engineers square is more accurate than the cube.  I still use the cube a lot, but not for everything.

 

Accurate setups make everything so much easier.

I use my combo square against the blade to square my miter gauge.  I want the cuts square to the blade and the blade has already been checked to be square to the slot.

We'll just make the assumption that the miter slot is parallel with the blade... Obvious first step.

 

I found an engineering square with a 3/4 base... Think I got it from McMaster-Carr for about $14.95 years ago...  Just drop it in the slot and you're done...

 

For the $15 -- it was worth it, use it for the bandsaw, stationary sanders, router table -- basically everything with a miter slot.

 

I've seen a purpose made jig -- can't remember if it was Rockler, Lee Valley or Woodcraft -- but it cost more than an engineering square...

Back in the day when I was cutting on the table saw 8 to 10 hours a day we would just flip the miter gauge upside down in the miter slot and push it up against the square tube for the fence and tighten it down. Flip it back upright and start cutting.

Drafting triangle against the fully raised blade, against the miter gauge.

Weird things happened when I tried to edit my last post.  A 1/10 of a degree is more than it might sound like. If I did the math right, 1/10 of a degree on a 24" radius, as with the framing square, is .042 inches.  A business card is .015 thick, and a piece of paper typically .003.

 

 Even with setting the blade to dead square, an engineers square is more accurate than the cube.  I still use the cube a lot, but not for everything.

 

Accurate setups make everything so much easier.

Thomas?  Square?....with a cube? Am i missing something? Has thou partaken of the egg nog? Partook?

==> Back in the day when I was cutting on the table saw 8 to 10 hours a day we would just flip the miter gauge upside down in the miter slot and push it up against the square tube for the fence and tighten it down. Flip it back upright and start cutting.

 

I used to do that too... Then one day I realized the thing wasn't perpendicular to the miter slot... Just a tiny bit out, but enough to be noticeable when mitering frames, Chippendale chest feet, etc... That's when I opted for the engineering square...

Back in the day when I was cutting on the table saw 8 to 10 hours a day we would just flip the miter gauge upside down in the miter slot and push it up against the square tube for the fence and tighten it down. Flip it back upright and start cutting.

 

We used the edge of the cast iron saw table, and it's accurate enough for some jobs, but not for others... 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.