chestermikeb Posted January 28, 2014 Report Posted January 28, 2014 Hi I'm looking to buy my first table saw (N00b alert!) but there is a question that has been bugging me regarding the blades. It seems I can buy blades which are designed to rip cut and also those which are designed to cross cut, but my question is, if you are planning on cutting a piece of stock to size in a number of directions (i.e both with and across the grain), do you need to change your blade each time you change the cut direction? I realise that you can also buy general purpose blades, but these normally seem to be quite coarse and not really intended for fine woodworking, so I guess you would need to do a fair amount of cleanup to the edges afterwards (Correct me if I'm wrong). So I wander what the recommended system is here? Do you swap blades each time you change cut direction or do you just use a cross cut blade (for example) to make rip cuts? Any advice or suggestions much apreciated Mike Quote
dwacker Posted January 28, 2014 Report Posted January 28, 2014 40t is fine for nearly everything. Don't overthink it. If you plan on ripping bunch bunch or get burning the switch to a rip blade. 1 Quote
Jfitz Posted January 28, 2014 Report Posted January 28, 2014 +1 to PB's advice. I usually run a 40tooth Forrest combination blade, and it works well for almost all my cuts. When I have concerns about burning on a long rip cut (especially with cherry or hard maple) I'll switch to my 24t rip blade. Takes less than a minute to change, so it's not a big deal. Quote
dwacker Posted January 28, 2014 Report Posted January 28, 2014 A bunch depends on the saw. Its impossible to give blade advice on "specialty blades" without know what HP your saw is. I have a 5hp saw so really only use a rip blade for 12/4 + but that is going to change as you go down in HP. Quote
Scott Keith Posted January 28, 2014 Report Posted January 28, 2014 I agree with the above advice. Get a good quality GP or Combo blade. You will use it on almost all your cuts. One key to clean cross cuts is a zero clearance throat plate. Even an 80t blade with splinter the backside some material if it is used with the factory TP. I only put in a rip blade if I know I have a lot of ripping to do all at once, or if it is some special stock that requires it. I will put in a CC blade if I am cutting a lot of ply. Other than that it a GP. I have been happy with the higher end Freud TK blades. Quote
dwacker Posted January 28, 2014 Report Posted January 28, 2014 One key to clean cross cuts is a zero clearance throat plate. If you use it right, most dont. If you use the plate right you dont need fancy plywood blades a good combo blade will make clean cuts in even the most fragile plywood. Most dont support the leading edge they just support the sides. Once a plate is cut to a specific depth the blade should be lifted to just scrub the leading edge and cut at that height only. If you need a lower height then you need a new insert to get the most out of the support. 1 Quote
Jfitz Posted January 28, 2014 Report Posted January 28, 2014 If you use it right, most dont. If you use the plate right you dont need fancy plywood blades a good combo blade will make clean cuts in even the most fragile plywood. Most dont support the leading edge they just support the sides. Once a plate is cut to a specific depth the blade should be lifted to just scrub the leading edge and cut at that height only. If you need a lower height then you need a new insert to get the most out of the support. Good tip! I've often thought about this (but unfortunately done nothing about it, since replacement inserts for my TS are a little on the pricey side). Quote
Scott Keith Posted January 28, 2014 Report Posted January 28, 2014 There is plenty of info on the web explaining the how to make your own ZCTPs, a much cheaper option. It's almost just as easy to make ten as it is to make one, so you will always have a fresh blank ready to go. You can even use a ZCTP on bevel cuts by raising the beveled blade up through a fresh plate. That plate become dedicated to that angle. Quote
Jfitz Posted January 28, 2014 Report Posted January 28, 2014 I made them for my old saw. I haven't taken the plunge to make any for my SS yet. Quote
dwacker Posted January 28, 2014 Report Posted January 28, 2014 I buy the Leecraft you can easily hear the blade hit the leading edge on the hard phenolic or what ever they are made of. They last months even with constantly changing the blade height all day every day. Quote
TerryMcK Posted January 28, 2014 Report Posted January 28, 2014 Mike as you are in the UK (Chester by any chance?) a 40 tooth combination blade from Axminster will be fine for crosscut and ripping - just to echo what everybody has said so far. Quote
chestermikeb Posted January 28, 2014 Author Report Posted January 28, 2014 Hi Guys, thanks for all the responses. It sounds like the way to go is the 40t blade. As I'm just starting out I guess I will learn as I go with regards to what works best but was just really curious about the fact that blades were sold on the basis of the type of cut you were going to be making. #TerryMcK: Yeah I am from Chester...how did you know! And yes I was also looking at the Axminster blades so will probably plum for one of those. Thanks for the advice. Cheers all Mike Quote
AceHoleInOne Posted January 28, 2014 Report Posted January 28, 2014 I have an under power saw, direct drive Delta...dont remember the HP rating??? I do rough rip cuts (rough sizing ) with a 24 tooth blade. Then I install a 40 tooth blade for cross and thin kissing rip cuts to finalize dimension. For me, the zero clearance is to keep thin waste from falling or jamming in the saw. -Ace- Quote
knotscott Posted January 29, 2014 Report Posted January 29, 2014 Most of what I know about saw blades right here.... Quote
Trip Posted January 29, 2014 Report Posted January 29, 2014 ==>know about saw blades right here.... TMI... Here's what you need to know: http://www.forrestblades.com/woodworker_2.htm Quote
knotscott Posted January 29, 2014 Report Posted January 29, 2014 ==>know about saw blades right here.... TMI... Here's what you need to know: http://www.forrestblades.com/woodworker_2.htm Now why didn't I think of that? Quote
Rick A McQuay Posted January 29, 2014 Report Posted January 29, 2014 A rip blade will take less power to rip than a combo. Might not be noticable with 3+ HP but it makes a difference on a 1.5 HP. My Freud rip will zip through stuff that slows down my combo blades.Sent from my T-Mobile G2 using Tapatalk 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.