otis Posted February 10, 2014 Report Posted February 10, 2014 I'm looking to get my first spray setup and want an hvlp turbine.i was looking at the fuji mini mites and Apollo Eco and am having trouble deciding if I should go with 3 stage or 4 stage. It will mostly be used for shellac , lacquer , and other finishes, but I need to spray my kitchen cabinets with latex paint. Will a 3 stage handle latex for a job like that? I might use it once in a while for latex but don't use it that often. And do I need another gun or anything else for different finishes? My budget is already maxed out with a 3 stage and another needle but if absolutely necessary I could probably come up with the extra money for the 4 stage. It's hard to find info on the Apollo Eco systems, has anyone had experience with them? How do they compare to the fuji? Thank you everyone for your info. Quote
dwacker Posted February 10, 2014 Report Posted February 10, 2014 I have an 1100 and a 1035 don't know about the Eco. A 4 stage would be best. Why latex on cabinets? Quote
Trip Posted February 10, 2014 Report Posted February 10, 2014 Eco is Apollo's 'value line' turbine... Apollo introduced the Eco series to compete head-to-head with Fuji's MiniMite series... It's new, so not much info available... I believe PopW did a review a few issues back.I don't know anyone with direct experience with the Eco line -- it's just too new... But buying Apollo is a bit like buying FT -- it's probably well made. If your budget allows, get the 4-stage. The world is going WB (and in many places, it's already there)... There's a big CFM/psi jump from the 3-stage to 4-stage that improves atomization of WB finishes. There's a bit of a debate on latex through a 3-stage (and even 4-stage) -- some swear they do it no-problem, some swear they can't get it to atomize properly at all... But PB's spot-on, why latex on kitchen cabinets in the first place? Unless there is some overwhelming reason for latex, there are plenty of other paths to an opaque finish. Quote
wdwerker Posted February 10, 2014 Report Posted February 10, 2014 I you are considering the long term use go 4 stage. I have been spraying HVLP turbines since 1989 and the Apollo is the best one I have used. There are a number of water bourne finishes that will work on your cabinets much better than latex. In an existing kitchen the biggest priority is cleaning and prep work before you spray. All the grease and dirt will cause problems with your finish. If it is available a primer or sanding sealer may help you acheive a better finish quality. Quote
otis Posted February 10, 2014 Author Report Posted February 10, 2014 Thanks for the input on the sprayers. Now I guess I need to start a new topic about what to put on kitchen cabinets :-) I watched ask this old house and on two episodes they primed then painted the cabinets with latex paint. They followed that with water based polyurethane. I tried a couple test doors by brushing like they did and could see brush marks and it didn't look good. So I figured spraying them would be quicker and look much better. If there's a better method I'm open to hear it. I've never done cabinets before. Also I don't want to see the oak grain or color anymore. Quote
dwacker Posted February 10, 2014 Report Posted February 10, 2014 Painting is a temporary solution. There is a difference between finishing and painting. If you have cabinets that you just want to change the color on until you get around to actually buying new cabinets or plan on flipping the house then great. I you a have good bones and want to keep the cabinets your better off refinishing them with a tinted finish either WB or solvent. Quote
wdwerker Posted February 10, 2014 Report Posted February 10, 2014 Covering oak grain requires using a grain filler and then sanding. Sometimes more than one coat is needed. But I don't blame you I am not a fan of oak myself. Having said that oak and ash do look very good finished in dark colors, just the grain shows and it is a nice effect. Quote
dwacker Posted February 10, 2014 Report Posted February 10, 2014 If you want to try solvent then vinyl sealer will easily hide the oak grain topped with a tinted pre cat. The high solids will easily fill oak but will need sanding before the top coat. Quote
Tom King Posted February 10, 2014 Report Posted February 10, 2014 You'll find better advice here than you will see on TV. 1 Quote
otis Posted February 11, 2014 Author Report Posted February 11, 2014 So if I were to use water based polyurethane tinted with transtint that would work? I would use dark walnut tint. Quote
dwacker Posted February 11, 2014 Report Posted February 11, 2014 So if I were to use water based polyurethane tinted with transtint that would work? I would use dark walnut tint. Yes but you will need to experiment to get the color you are looking for. If you put enough trans tint in the poly its going to go solid. Generally transtint is used to provide a more translucent top coat. If you want something more along the line of paint your better of buying color matched finish. I guess what Im trying to say is there is more to it than just adding color to your finish. Honestly your always going to be better off going to someplace like SW or rodda and buying the exact color that you need in the form that you want it. Transtint is fine for a one off small piece like furniture but not great if you have a bunch of finishing to get done. The only real use I find transiting good at is making a custom color on a sample board but even then Ill go to rodda and buy finish in gallons precolored to match the board I make with trans tint. Quote
otis Posted February 12, 2014 Author Report Posted February 12, 2014 Thanks again for the help. I'll be checking SW out to see what they can do. Also ended up going with the 4 stage fuji anyways. Can't go wrong with more power. Quote
JerrySats Posted February 12, 2014 Report Posted February 12, 2014 I recently bought the Fuji Mini Mite 3 . I'm very happy with how it sprays . I shoot mostly PreCat Urethane and water borne finishes . I'm with the others on using latex for your cabinets . There's so many great products out there to use that are meant for just this application. They are super easy to use with great results that will hold up to the abuse . Price wise I think you'll find them cheaper then the high end latex from any of the paint stores and you still won't get the performance from those products that you will from a WB product. I started using ML Campbell products about 1 year ago and I'm ex termly happy with how it preforms . My local supplier can do a color match for me . http://www.mlcampbell.com/products/categories/pigmented_topcoats/water_borne/precatalyzed/agualente_whiteopaque_base 1 Quote
estesbubba Posted February 19, 2014 Report Posted February 19, 2014 This is General Finishes milk paint sprayed over stained oak cabinets with a Mini Mite 4 (still wet) Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.