Recommended Posts

Posted

Any update on this? I would also like to know if you are happy with the MDF top with the Incra LS unit.

Thanks!

I'll update you on the router this afternoon if at all possible. As for the Incra, I'm not in a position to purchase it yet. Although I believe Incra's own tops are laminated MDF.

Sent from my HTC One using Tapatalk

Posted

OK, very limited first impressions since I haven't been able to throw a lot at it yet:

 

It handled what I threw at it just fine, flush trimming curly maple to a plywood top. Not the hardest thing I could do, but it's what my project called for. The soft start isn't what I'm normally used to. On my Craftsmans it legitimately soft starts - the speed starts low and then it ramps up to the set speed. On the Triton, you flip the switch, nothing happens for a half-second, and then it's on full blast. I searched around, and this is claimed to be normal. Not what I was expecting.

 

The above-table adjustment is awesome. I love the little winder handle. It does have vertical lash, however that's eliminated by locking the plunge mechanism. Duh on my part. Similar to not remembering to lock the motor in the base. The automatic collet lock is brilliant, I hated trying to reach into the plate opening to depress the button while trying to loosen or tighten the collet (previous router). There is a slight hiccup if you use an external control switch, in that you'll have to reach in and flip the switch on the router. How the lockout works is that the collet won't lock if the power switch is on, and the switch cover won't open if the collet is locked. The switch cover stays open while the switch is in the on position, closes when off. Clever.

 

Also on the safety front, nearly the entire area between the base and the motor is enveloped in a shroud. The only real part where you can get your fingers in is the manual collet release for handheld mode. I would assume this is fantastic for dust collection, but haven't had the opportunity in either mode. This thing is going to spend 95% of the time in the table.

 

I had a moment tonight when I was finishing up that the collet wouldn't raise all the way up to lock. It was a combination of the plunge depth stop and the switch being in the on position.

 

I have it mounted to the Kreg predrilled plate. At first I wasn't sure how they oriented it (caddycorner), but it's an intelligent design. I can easily access the plunge lock lever from the front, and the switch is on the right back side, but easy to find. I think they had to do it this way to keep the height adjustment from interfering with a fence.

 

I went with a 1.25" (.75, .5) MDF top. I used the Kreg levelers so I didn't have to worry about a rabbet. I cut it to length this evening, it will be approximately 24x36, with the front edge of the plate 8" from the front edge of the top. I'll be rounding the corners and applying melamine to the top, bottom and edge.

 

The router table carcass is basically done. I planned to use Dominos, but I just couldn't be bothered. I'll be adding some support blocks so that the top can be mounted to the carcass tomorrow, and the casters go on too. After that, I'm not going to be able to set foot in my shop for at least a week. Wanted to get over this hump before this break.

Posted

I have an old style Rockler aluminum/MDF fence that I used in t-tracks in the old table. I designed this table to have the capability to clamp this fence down. After the Incra is installed that space will be used to quickly access the wrench and the setup bars.

I'll be going into more detail on my blog, and I'll let you know when the stuff from today is up.

Sent from my HTC One using Tapatalk

  • Like 1
  • 3 weeks later...
Posted

Mel...check out Infinity tools, they have a Triton 3 1/4 with table, lift jessem fence..... I just built my router table , never used a lift, but my table raises for access., 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.