Recommended Posts

Posted

Got my 230v 20a outlet installed this am, and the PM2000 was delivered soon after.

The freight delivery guy had a heck of a time with the 700lb palette. Luckily, the next door neighbor's kid and his 5 offensive linemen friends were there to help (for a fee of a few pizzas).

Very stoked to set this puppy up. No more can I blame my uneven work on my Delta Shopmaster II with the wonky fence, uneven surface, and shaky vibration.

Nope, now I'll blame my uneven work on myself! :)

Seriously though, how is it to set up, align, etc, out of the box? Pretty straightforward?

Thanks all

Posted

That's quite an upgrade!

 

I got my Jet 1.5 hp shaper today too.  I didn't have a neighbor or his kid's 5 football playing friends to help.  What I did have was a steep icy driveway and a 200 lb shaper on my legs when I ended up on my butt.  Good thing I didn't go for the 3 hp I guess.  But the driver and I got it up the driveway and my dad and I got it in the basement.  The funny thing is my mom is in the hospital with two fractured legs (okay, that part isn't funny) and now I've got bruises in the exact same places she has fractures.

Posted

Setup isn't bad; it took me a day and that included wiring in a 25' cord.  However I think you might need to have a larger circuit :unsure:.  Most 3hp motors call for a 30A breaker, and 5hp put you into the 40A category.  What size wire did you run from the panel to the outlet? 

 

It's a sweet saw, you're going to love it!

Posted

Setup isn't bad; it took me a day and that included wiring in a 25' cord.  However I think you might need to have a larger circuit :unsure:.  Most 3hp motors call for a 30A breaker, and 5hp put you into the 40A category.  What size wire did you run from the panel to the outlet? 

 

It's a sweet saw, you're going to love it!

I'll tell you something strange....when I got my Grizzly 5HP table saw, the manual called for a 14 gauge wire coming from the panel box to the saw.  On the back side of the saw, there is a connection box where the primary power wire connects.  They are stranded wires and I think they're 16 gauge wires that go to the motor!!! That's freaky to me.  I said heeeeeck no, I ran a stranded 12/4 to the panel box.  Never going to go wrong running too big of a wire...just too big of a breaker.

Posted

==>Got my 230v 20a outlet installed this am, and the PM2000 was delivered soon after. 

 

==> Most 3hp motors call for a 30A breaker, and 5hp put you into the 40A category. 

 

Because all 3HP motors are not created equal, it's important to check the specification plate mounted to the motor housing for power requirements.

 

Note: HP in woodworking tools has evolved into a marketing spec, so one person's 3HP is another's 2.5HP. At this point, you can trust most manufacturers to error on the high-side of HP specs*...

 

In general, a 3HP motor of average efficiency will draw around 240/18.5a at load (and closer to 240/12.5a nominal) . To handle in-rush, mfgs typically specify up-gauging. So, Powermatic may require a 30a/10AWG circuit for the 3HP PM2000.

 

As always, check the motor housing just to make sure.

 

*Note: If the power is specified in kw, then it's probably accurate...

Posted

I believe the 13a rating is it's draw once it's up to speed; typically startup will spike higher than that, then come down.  If it's a short run from the panel to the outlet it will probably be fine.  If it's a long run then there may be enough line loss causing the breaker to pop or possibly damage the motor. 

 

I'd see how fast it comes up to speed when turned on.  It should only take a second (literally).  If it's taking much more than that I suspect it may need more juice :). 

Posted

Good to know. Thanks guys

Well....I'll certainly be the guina pig and let you know how it works. The outlet is only about 20 feet from the breaker box (hanging from ceiling in photo)

Ok. Million dollar question, and clearly I'm getting wiser I'm my older age because I'm smart enough to ask.

For those of,you who've done this, what's the best way to get this 600lb beast of the palate.

I'm thinking, lower the casters, rig up a ramp, and wheel it down?

My 5 month old son isn't much help....he needs to start pulling his weight around here.

post-15261-0-78699800-1394843627_thumb.j

Posted

Progressive platforms. You can safely tip that far enough to transition to a platform that is half the height of the pallet and then down to the floor. I am a huge fan of the vinyl furniture glides that can be found at most dollar stores.

Posted

==>Crank the wheels down roll one side off. Move to the other side tilt the saw and kick the pallet out of the way.

Must admit I do this (or something similar) with quite a few deliveries...

 

But after watching that funny tablesaw scene in Marc's 'shop move' video, I really don't recommend that method anymore... :)

 

While I'm on the subject, the best part of that video is the contractor using Marc's jointer in/out-feed table as a ladder -- that's priceless.

Posted

==>Crank the wheels down roll one side off. Move to the other side tilt the saw and kick the pallet out of the way.

Must admit I do this (or something similar) with quite a few deliveries...

 

But after watching that funny tablesaw scene in Marc's 'shop move' video, I really don't recommend that method anymore... :)

 

While I'm on the subject, the best part of that video is the contractor using Marc's jointer in/out-feed table as a ladder -- that's priceless.

 

Man up. :) I weigh a 140lbs soaking wet and moved every piece of equipment in my shop off the pallets and into position by myself including a 1000# bandsaw. It takes brains to move heavy objects not brawn.

Posted

Saw all set up. Ripped through 8/4 Mahogany like hot butter. No problems at all on the dedicated 20a circuit.

Aligning the tops was do-able by myself, but a second person would have saved me a few hours.

The wooden extension table was just too difficult to attach and level on my own. - I'll wait for a second set of hands for that one.

Only major complaint, is that I stripped both accufence soft plastic hex alignment screws on the the first try. I'm sure the company will be happy to replace them when I call.

Thanks for all of your input

VJ

post-15261-0-23405200-1395155559_thumb.j

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 59 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined