Recommended Posts

Posted

Hello, I'm new to woodworking, power tools and Wood Whisperer. I'm taking a woodworking class at the local college and am a bit 'spatially-challenged' related to cutting to the line with the table and chop saws. 

 

I'm in the process of dimensioning wood for my tool box project and need to rip and cross cut down to size. Not being at all facile with these power saws, I've done some hand sawing in the past, I'm not sure where the kerf of the blade is going to go when I have to make the final precise cut to size. 

 

I don't want to screw up at this stage given all the effort I've put into jointing and planing these boards. 

 

Any tips and insights are MUCH APPRECIATED! Thanks : )

 

ramone

Posted

Suggest setting up stop blocks.  Clamping a stop block in will give you repeatable accuracy.  

 

If you're having trouble figuring out the first one (to locate the stop block) suggest using a piece of scrap.  Once it's the correct length, use that for the location of your stop block and clamp it in place.

 

Oh, welcome to the forums Ramone!

  • Like 1
Posted

A standard table saw blade cuts an 1/8" kerf (.125 ) ( or very close to that). A thin kerf table saw blade cuts a 3/32 kerf (9.09375)

Band saw kerfs are usually much thinner but it depends on the blade. 1/16" kerf is a fair guess.

Posted

If you can, take some practice cuts on some scrap wood, to get an idea of where the kerf ends up and how to line up the cut.  Also, I like to "sneak up" on the cut.  You can always make a board a little shorter, but if you cut too much you've ruined your board.  So, cut it deliberately long by about an 1/8".  Then check to see how much over you are and make another cut about halfway to your goal.  Keep getting closer and closer until you are satisfied.  If each cut is just a hair more than the last cut, then even if you mess up you'll still be less than a hair away from perfect.

 

I'm a big fan of "relative dimensioning".  Let's say that you are making a picture frame and the sides should be 12".  If both sides are 11 7/8" you'll still have a perfectly good frame.  But if one side is 12" and the other is 11 7/8", your picture frame will be crooked and your joints will have gaps.  So, instead of cutting both sides to be 12", cut one side to be 12", and the other side to be exactly the same length as the first side.  In other words, use the piece you are trying to match instead of a ruler to measure your cuts.

 

Finally, here's a wood working secret.  Instead of using a pencil to mark your cut locations, use a sharp knife.  The knife will make a thinner mark, and there are times when it matters whether you cut on one side of the pencil line, the other, or the middle.  Also, the knife will cut the wood fibers on the surface, so if you line up the edge of the kerf with the knife line, you'll get less tear-out when you cut.

  • Like 1
Posted

One more tip: don't trust the measuring tape on the saw's fence rail, especially if it is a saw that you don't own. With power removed, use a good ruler or gage piece to measure from the fence to the edge of the blade teeth nearest the fence.

If you are hand sawing, I find that making a light 'groove' cut with the saw along the layout line really helps guide the saw once you are cutting through. To that end, laying out the cut on all affected sides of the board helps as well. Don't assume you can mark one side and eyeball your way to a clean and square cut.

Posted

I had the exact problem when I transitioned from doing more construction stuff to woodworking.  Follow the advise given, it works.  Use measurements to get your first cut but after that you need use the cut piece as your reference.  

 

Stop blocks are your friend and just planning your cutting so all the similar parts are cut at the same time will help.  Example if you have to rip 4 pieces 4" wide, don't do one and then move your fence for another part.  Rip all 4 at the same time.

  • Like 1
Posted

I think the simplest bit of advice I didn't see in any of the comments here is to know which side of your line to cut to.   If you properly dimension your first piece and use other aids, like stop blocks, to cut pieces that need to match, knowing which side of your set up line on your first piece to cut to will get that piece, essentially the template for the rest of your work, set up correctly.  Typically, trying to cut down the center of the line is difficult to do and may bring problems with precision.  Cutting to the inside of the line will make your finished item short by the thickness of the kerf and to the outside will make it the measured length.

 

Personally, I don't like sneaking up on the line for a few simple reasons.  First of all, any extra cuts you need to make are wasted time.  I prefer to use that extra time in making sure that my layout is done properly and then making one cut.  

 

Second, each additional cut you make to "sneak up" on what should be the correct cut is a new opportunity for something to go wrong.  

 

Finally, it just inherently infers a lack of confidence.  If I don't have faith in my ability to do something correctly it really sets up the opportunity for something to go wrong.  Instead, I prefer to believe in my skills and layout ability.  The more I believe in my own skills, the better the woodworker I become.  There's less paralysis by analysis, less redoing things and more accepting the outcome of my efforts.

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 59 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined