Pwk5017 Posted June 4, 2014 Report Posted June 4, 2014 Second post here, and I am looking for some advice on what tool purchases to make early on. I became recently involved with woodworking, and going on month #5 now. Started out with a dewalt miter saw that I used for trim carpentry when remodeling the house. Then, decided I needed a table saw, but budget was super tight, so I went with the dewalt portable model. Next, I decided I needed a router, and I purchased a new bosch plunge and fixed base on CL for $125 with a new in box guide. Then came the aluminum bosch router table. Then Bill Pentz's site gave me nightmares, because my shop is in the basement of my girlfriend and my house. I purchased a 1.5hp shopfox on CL for $150, bought the wynn canister for it. I plan on going with the Oneida super dust deputy as a separator to protect that super expensive filter. To finish out the dust control, I want to get an air cleaner to catch the inevitable escapee dust. I should add that I have been wearing a 3M respirator the whole time, but still the dust had to eventually make it into the upper living space. So, this is where I need some help. I have a pretty low end setup, and funds are tight, since im two years out of school and swamped with student loans and a car loan. A few things that im considering: Air cleaner - should I go with the Jet model or the new JDS air tech? Looks like the JDS might have a slight advantage in filter efficiency and the RF remote, but its more money as well. Milling lumber - I have wanted a dewalt 735 since I got started based off all the stellar reviews. Also, didn't take me long to realize finished lumber at the big box stores is extremely pricey. Finding a 735 on CL is like a needle in a haystack. 4-5 months of checking CL daily has returned one opportunity, and I missed that opportunity last night by ten mins. I called the guy, and he said somebody called ten minutes before me, and wanted it no questions asked. Bummer. Now I am wondering if I should settle for a dw733 or delta 12.5" planer for closer to $200-250 instead of buying a new dw735x in the $540 range. I also don't want a piece of crap that is going to provide endless headaches dealing with snipe etc. I don't want milling lumber to become an incredible PITA. Finally, how crucial is a jointer at this stage? I purchased a $20 freud 1.5" straight bit to serve as a poor man's face jointer after watching marc do it on his roubo bench. I also plan on building a bench for my next project, so I will need it for flattening the bench. I have seen plenty of old deltas and craftsman 6" jointers in the $200-250 range, but they all seem like 20 year old garbage. Plus, I have read 100 times that I should just save my money and get the 8" as my first jointer. So do I buy a new dw735 planer, and use jigs to joint for the next 6-12 months before I purchase an 8" jointer, or do I buy a used dw733 and a used 6" jointer for the same price? Lastly, holy cow is this hobby pricey!! Thankfully, I have been selling various things made in the shop to cobble together the $1400+/- that I have spent thus far, but it has been a rocky adventure of coming up with the money necessary to get a shop together. Quote
pghmyn Posted June 4, 2014 Report Posted June 4, 2014 I'll try to keep it short and not over load you with details. If you have to settle for one tool, get a planer. You can use a face jointing jig on the planer. Although not ideal, it can be done. If you want both, get a grizzly 6" jointer and a cheap surface planer. If you are getting both, you want to spend more money and get more precision with the jointer. There are easy ways to deal with snipe, and you will learn about them. Snipe is practically inevitable. No matter how big or small it is, it is pretty much always going to be there. I use an old Delta surface planer. The snipe is awful on the first and last 2.5" of the boards, but flawless and precise thickness throughout the remainder of the board. Here is the best explanation of snipe: I don't care what anyone says about tables being the reason for snipe, I am not believing it. Here is the method I use to reduce snipe dramatically: Quote
knotscott Posted June 4, 2014 Report Posted June 4, 2014 There are lots of plans to build an inexpensive air filter. They can be remarkably simple, and will save some money.....put it towards a jointer! While the DW735 is definitely one of the best, if not the best portable going, it's expensive, and it's not perfect. Other planers can perform remarkably well....I've done well with the better Delta and a Ridgid R4331. The DW734 gets good marks too. Snipe has rarely been an issue once the planer is setup well. I personally would rather have a functional planer and a jointer, than the king daddy of all planers and no jointer. I've managed with a 6" jointer for 13 years now....it'd be nice to have an 8" on occasion, but I don't have the space or the budget, and do quite well with a 6". Watch CL for an older functional jointer. Quote
mikem Posted June 4, 2014 Report Posted June 4, 2014 I have a Dewalt DW734 planer and a Grizzly G0654 jointer. I have been happy with the plane, and mostly satisfied with jointer. When I first got the jointer, not quite 2 years ago, I didn't dial it in as well as I should have. This past weekend that became apparant when I was attempting to edge joint two boards for a glue-up. It only took an hour or so, and some pop can shims, I got the jointer dialed in so that the tables are coplaner, and the outfeed is at the right height. Now that it is dialed in, it performs very well. Quote
RichardA Posted June 4, 2014 Report Posted June 4, 2014 I have a 735, and you will soon learn two things, #1 make sure you get the in and outfeed tables and set them up properly! #2 The 735's blades do not last long, no matter how light a cut you take, Use them, and hone them once then toss them, and call Infinity tools and get a set of their replacement HSS blades, you'll be rewarded with a longer blade life and better re sharpining times. 1 Quote
Pwk5017 Posted June 5, 2014 Author Report Posted June 5, 2014 Thanks, guys, great advice so far. One, I could make my own air cleaner for roughly $300 using a wynn nano filter and an inline1000cfm fan, but at that point, I would rather spend the $80 and not have to build an air cleaner that might not be as effective as the manufactured one. Plus, the extra features of having multiple speeds, a RF remote etc. I figure if I go idiotic on one aspect of this hobby, it should be dust control and mitigation. If my shop was in a shed outside, I would care, but its in the house. Seems like most are leaning towards getting a cheap jointer and a cheap planer. I really have not seen many opportunities for decent 6" jointers on CL, so that might have to be a new purchase. In Pittsburgh, all I see are horrendous looking Deltas, and craftsman jointers for $200ish. Then, anything that looks decent like this http://pittsburgh.craigslist.org/tls/4443012591.html is outrageously expensive in my opinion. And If im spending $600+ on a 6", then I might as well go another 2 months without a jointer and get the 8" for $795. That is why I was asking if I should just get a nice planer now, deal with not having a jointer for a few months, then buy Grizzly's 8". I guess I have already experienced the one side of the picture where most of my tools are inadequate. Most woodworkers would laugh at my dewalt table saw. It looks like a toy, but $275 does not buy you much saw, and I got a deal on this one. I do wonder from time to time whether it would have been better to postpone the hobby a month or two, to have $400 to spend on a saw. That is my big picture question, better to have an inexpensive and potentially inadequate version of every tool, or to postpone your involvement in the hobby while you build an adequate shop? Quote
knotscott Posted June 5, 2014 Report Posted June 5, 2014 When I suggested a shop made filtration system, I was actually thinking in very simple terms and low cost. Most that I've seen can be built for < $50 with a box fan and a furnace air filter, and are quite effective. Also, you might be surprised at how well cast iron will clean up. A dirty, slightly rusty tool often poses an opportunity to pick up something below market value. The plus side about buying a decent used tool at a good price is that it maintains its value very well. A decent $150 to $200 planer or jointer will still be worth $150-$200 in a year or two. Cleaned up and running well, they might even be worth more. (I did see a couple of Delta tools that looked to be viable options). Ultimately, you have to buy what you're comfortable with, and I don't want to persuade you to do something you're not comfortable with, but did want to point out realistic low cost options that represent good value (IMHO). Quote
Coop Posted June 5, 2014 Report Posted June 5, 2014 I have a 735, and you will soon learn two things, #1 make sure you get the in and outfeed tables and set them up properly! #2 The 735's blades do not last long, no matter how light a cut you take, Use them, and hone them once then toss them, and call Infinity tools and get a set of their replacement HSS blades, you'll be rewarded with a longer blade life and better re sharpining times. Richard, Was not aware of these replacement blades. Thanks Quote
Pwk5017 Posted June 5, 2014 Author Report Posted June 5, 2014 When I suggested a shop made filtration system, I was actually thinking in very simple terms and low cost. Most that I've seen can be built for < $50 with a box fan and a furnace air filter, and are quite effective. Also, you might be surprised at how well cast iron will clean up. A dirty, slightly rusty tool often poses an opportunity to pick up something below market value. The plus side about buying a decent used tool at a good price is that it maintains its value very well. A decent $150 to $200 planer or jointer will still be worth $150-$200 in a year or two. Cleaned up and running well, they might even be worth more. (I did see a couple of Delta tools that looked to be viable options). Ultimately, you have to buy what you're comfortable with, and I don't want to persuade you to do something you're not comfortable with, but did want to point out realistic low cost options that represent good value (IMHO). No way, man, you didn't offend me or make me uncomfortable. I admitted in the first post that I am young, up to my eyeballs in student loans, and I have the pending doom of buying an engagement ring in the near future! That's why I was asking if I should just hold off on buying all this stuff at once, and make do with what I have. If a $200 jointer isn't as much of a piece of crap as I envision it being, then that's cool, I will look for one. But if it is junk, and I am only going to use it for 6 months before I slap it on CL for $50, then I would rather do without for a few months, and get something worthwhile. After all, it is summer, and theres plenty of fish to be caught. That is why I was asking you all. I have never used a planer or jointer in my life. I haven't the faintest clue what is the right course of action. I can read reviews until my eyes bleed, but its hard to find reviews on used CL jointers that are 20 years old. They might be in a magazine somewhere, but they aren't reviewed online, and therefore impossible for me to gauge. Quote
knotscott Posted June 5, 2014 Report Posted June 5, 2014 ...I have the pending doom of buying an engagement ring in the near future!.... Ha, ha....I sold my 1976 Suzuki GT750 to buy an engagement ring for my wife back in 1980. Best investment I ever made! I wouldn't mind having that bike back, but I traded up for sure! It's hard to tell from the pics on CL whether or not a tool is in functional shape, but the two Delta jointers I saw looked like they had potential. With floor standing cast iron jointers, check that the infeed and outfeed tables are co-planer with each other...you can do that by raising the infeed table to the same height as the outfeed table, then lay a long straight edge across both tables. Check that the fence is flat and square to the the tables. Also spin the cutterhead and listen for bearing noise. It should run quietly with little to no vibration, but even some vibration is likely belt or pulley related, so check those too, but know that they're easily replaceable. If there is unusual vibration or noise, ask the owner to remove the belt and run just the motor....it'll help isolate the source. Light rust on cast iron cleans up pretty easily....it just looks bad! I wouldn't suggest buying a used benchtop jointer....or even a new one if space constraints aren't forcing you to. It's harder to evaluate planers, other than overall condition. Have the owner run a piece of wood through....if it sounds normal (which is loud, but there shouldn't be grinding squealing or otherwise unusual metallic or grating sounds), feeds the wood, and leaves a reasonable surface, they should be ok.....ridges on the boards mean nicks in the knives, which is common, and is fixable with new knives or sharpening....check that new blades are still available if the knives are the disposable types. Even if the wood doesn't feed all that well, it's often just a matter of cleaning the rollers....just be sure they're not cracked or damaged. I was faced with an unexpected planer purchase a couple of weeks ago, as I managed to damage mine.....there wasn't much that was overly enticing on CL at the time, so rather than spend $250 on an older unit, I opted to spend $310 shipped on the Ridgid R4331 refurb with a 1 year warranty from Tyler Tool....it's no DW735, but has worked fine so far, plus I have some recourse if there's an issue. In that case, spending $60 more for the refurb made sense to me, and was still $100 less than new from the local store. You've probably already noticed that there's really no universal correct approach to this...it's largely a matter of opinion, and doing what suits our needs and circumstances, which is why I mentioned that you'll need to do what makes sense to you in the long run, even if those of us with more experience don't necessarily agree. Do the research, use your head, but follow your gut too....if it doesn't feel right, don't bother. Good luck! Quote
Pwk5017 Posted June 5, 2014 Author Report Posted June 5, 2014 A crappy jointer will be the bain of your existence. The whole reason to get a jointer is to make your surfaces precisely flat and square. No, you do not need to spend thousands to get one. People have had good luck with the entry level Grizzlies, so I would start there. Like I said before, it you are patient and mechanically inclined, rehabbing an old jointer might work out for you. For me it would be a trail of WD40, grease, dust and tears. I'd pull my hair out and be pissed off I was playing with wrenches and not shaping wood. This is precisely what has me so apprehensive about the CL deals on some tools. I haven't used a jointer before, let alone restore and tune one! In addition, I drive a hatchback. It isn't the most conducive vehicle for transporting a floor model jointer. I think I could take the table off the cabinet of a 6"er and fit it into the car, but otherwise it would be renting a truck/uhaul to get it back to my place. Yet another vote for ordering new... Assuming most benchtop planers perform the same, what brand should I go with? Looks like it shouldn't be too hard to get a Delta planer(varying models), or a Dewalt 733 for $200. I have seen a few in the past, and I believe there are a couple within an hour's drive at the moment. Any reason to go with one over the other? If it is going to perform just about as well as a new dw735, no reason to spend the additional $300-350. I can put that towards the future jointer purchase. And I haven't let not having a certain tool keep me from working on projects! I just admitted to being willing to use a router and a jib to face joint boards haha. It even sounds nonsensical, let alone how I will feel after doing it a few times. Ive built a 3'x7' shop table to hold my router table and table saw. The bottom has a shelf to organize my router, circular saw, bits, squares, drills etc.Then, I have been working on all my etsy stuff, so I can afford more tools. However, now I want to build a closet built-in for myself, and I want to tackle a cheap version of the roubo bench. Clamping work pieces, so I can rout dados and mortises has been a pain so far. Also, looking forward to having a dedicated assembly area that isn't a 3' by 3' card table. These two projects are what sparked the interest in milling lumber. All my other projects were produced using construction grade kiln dried studs and MDF. I might make my roubo out of the same construction grade wood to save on money, but I would like it to be one of my first hardwood projects. Agreed. Everyone should read Bill's site once, and then not be allowed to visit it anymore. Its like WebMD, you will convince yourself you have cancer or some incurable disease if you read it too long. Im spending more on dust control than any other tool, but I don't want to expose my girlfriend or I to a ton of dust. Quote
knotscott Posted June 5, 2014 Report Posted June 5, 2014 The key features are at least as important as the brand name. It's well worth getting a planer with some form of snipe reduction designed into it....either a cutterhead lock or a 4-post screw design. A dust port is another feature worth having that not all have. Some entry level models don't have a cutterhead lock and are more prone to snipe.....PC 305TP, Grizzly G0505, Ryobi AP1301, former Delta 22-540, TP300/TP305 come to mind. The Delta 22-560, 22-580, TP400, current 22-590, former Ryobi AP1300, Ridgid TP1300, DW734 and at least some of the Steel City models have them. The former Ridgid R4330 had a 4-post screw design that only worked marginally well. The DW735 has an effective 4-post screw design and newer Ridgid R4331 now has a cutterhead lock....both go as far as to include a chip ejector blower in the unit too, so you'll get some chip removal even without a dust collector. Quote
BuilderBill Posted June 6, 2014 Report Posted June 6, 2014 Second post here, and I am looking for some advice on what tool purchases to make early on. I became recently involved with woodworking, and going on month #5 now. Started out with a dewalt miter saw that I used for trim carpentry when remodeling the house. Then, decided I needed a table saw, but budget was super tight, so I went with the dewalt portable model. Next, I decided I needed a router, and I purchased a new bosch plunge and fixed base on CL for $125 with a new in box guide. Then came the aluminum bosch router table. Then Bill Pentz's site gave me nightmares, because my shop is in the basement of my girlfriend and my house. I purchased a 1.5hp shopfox on CL for $150, bought the wynn canister for it. I plan on going with the Oneida super dust deputy as a separator to protect that super expensive filter. To finish out the dust control, I want to get an air cleaner to catch the inevitable escapee dust. I should add that I have been wearing a 3M respirator the whole time, but still the dust had to eventually make it into the upper living space. So, this is where I need some help. I have a pretty low end setup, and funds are tight, since im two years out of school and swamped with student loans and a car loan. A few things that im considering: Air cleaner - should I go with the Jet model or the new JDS air tech? Looks like the JDS might have a slight advantage in filter efficiency and the RF remote, but its more money as well. Milling lumber - I have wanted a dewalt 735 since I got started based off all the stellar reviews. Also, didn't take me long to realize finished lumber at the big box stores is extremely pricey. Finding a 735 on CL is like a needle in a haystack. 4-5 months of checking CL daily has returned one opportunity, and I missed that opportunity last night by ten mins. I called the guy, and he said somebody called ten minutes before me, and wanted it no questions asked. Bummer. Now I am wondering if I should settle for a dw733 or delta 12.5" planer for closer to $200-250 instead of buying a new dw735x in the $540 range. I also don't want a piece of crap that is going to provide endless headaches dealing with snipe etc. I don't want milling lumber to become an incredible PITA. Finally, how crucial is a jointer at this stage? I purchased a $20 freud 1.5" straight bit to serve as a poor man's face jointer after watching marc do it on his roubo bench. I also plan on building a bench for my next project, so I will need it for flattening the bench. I have seen plenty of old deltas and craftsman 6" jointers in the $200-250 range, but they all seem like 20 year old garbage. Plus, I have read 100 times that I should just save my money and get the 8" as my first jointer. So do I buy a new dw735 planer, and use jigs to joint for the next 6-12 months before I purchase an 8" jointer, or do I buy a used dw733 and a used 6" jointer for the same price? Lastly, holy cow is this hobby pricey!! Thankfully, I have been selling various things made in the shop to cobble together the $1400+/- that I have spent thus far, but it has been a rocky adventure of coming up with the money necessary to get a shop together. You think this hobby is pricey? Really? Try collecting vintage Martin guitars or watch collecting. Or acquire the taste for taking pictures of itty-bitty birds at long distances. Woodworking is cheap at twice the price in comparison, trust me on this. OK, so here you are: limited funds and the desire to progress. A planer won't flatten a face or square an edge, you need a jointer for that. Then you need a planer to surface the other face parallel. So I'd recommend a decent jointer you can afford whether it's 6" or 8" and the DW 735. Craigslist for the jointer, crap-tons of them out there, may take some tinkering(hopefully you're mechanically inclined if not double the budget for new). Buy what you can afford and make do, there's no end to the progression. Sooner or later(if the hobby sticks) you'll acquire an 8" or 12" or 16" jointer depending on the depth of your addiction and the size of your shop(and your ability to transport machinery => 1/4 ton in weight). So get something that works well and is affordable.The DeWalt is a decent planer, there are deals on it everywhere, get the Infinity HSS blades when you wear out the ones it came with. If you have some spare change, put a Byrd head in it. Or not if you find it too slow, too small or too noisy, deal with the shortcomings and save the bucks for a real planer. You'll know after a few months whether this is something you want to stick with or not. Get decent but not extravagant tools to start with, upgrade if/as you feel the need. Take small steps, don't spend more than you can realistically afford until you know you're hooked. The resale market for entry-grade tooling is dismal, don't think you can get anywhere near close to your money back for the stuff you've outgrown. After the first round and you decide this is something you want to stick with save your money for tooling that will last you a lifetime. Take it slow and easy, a piece at a time as your needs grow and the budget allows. You'll get there, just not tomorrow. And if you decide along the way woodworking isn't your thing you'll minimize your losses. HTH, Bill Quote
Pwk5017 Posted June 6, 2014 Author Report Posted June 6, 2014 Haha this is true, I do not know the price required to take photos of birds at long distances. Really, if this were my only hobby it wouldn't be too bad, but I am also consumed with fly fishing(gotta have that top line gear, right?), bonsai, and Mont Blanc fountain pens. And yes, this hobby has a steep buy in cost. I would say I'm already hooked. I just love building things, so this was a natural pairing for me. You guys have helped me make my choice. I'm gonna get the dw735 and keep an eye out for a decent 6" jointer on craigslist. If a jet, grizzly, delta of decent quality pops up for $300-400, then I'll grab it. If not, then I'll save my money for a new 8" grizzly. Thankfully, these are the last two pieces of the puzzle I need for a solid workshop. I just need to be patient and make the right additions instead of getting something cheap to fill the void. I appreciate everyone's input. 1 Quote
Jasahan Posted June 6, 2014 Report Posted June 6, 2014 EDIT: replied before I read your last reply, wherein you made your decision. Don't know if you've made your choice yet, but here's what I have to offer from my limited experience. I work in a shop. We had a 12" planer (old foley-belsaw). When it ran, it ran all day. But it consistently had belt and bushing issues. We bought a 6" jointer from Harbor Freight. If I remember right, we got that before we got the planer, and actually iused it as a planer (we use all pallet wood). The cheap jointer sucked so bad. It never stayed square, and I couldn't get the two tables set up to save my life. The jointer is now another horizontal catch-all surface. We just bought a Grizzly 15" planer. Love it. Weekly, I find one of us saying, "If we had a jointer..." We have to try to get stuff "straight" with the planer and table saw. It does not work well, and it affects glue-up (and other things), which is especially bad because we make a lot of table tops. I'm convinced the best way to avoid snipe is to plan ahead and cut it off. Quote
Pwk5017 Posted June 6, 2014 Author Report Posted June 6, 2014 EDIT: replied before I read your last reply, wherein you made your decision. Don't know if you've made your choice yet, but here's what I have to offer from my limited experience. I work in a shop. We had a 12" planer (old foley-belsaw). When it ran, it ran all day. But it consistently had belt and bushing issues. We bought a 6" jointer from Harbor Freight. If I remember right, we got that before we got the planer, and actually iused it as a planer (we use all pallet wood). The cheap jointer sucked so bad. It never stayed square, and I couldn't get the two tables set up to save my life. The jointer is now another horizontal catch-all surface. We just bought a Grizzly 15" planer. Love it. Weekly, I find one of us saying, "If we had a jointer..." We have to try to get stuff "straight" with the planer and table saw. It does not work well, and it affects glue-up (and other things), which is especially bad because we make a lot of table tops. I'm convinced the best way to avoid snipe is to plan ahead and cut it off. Yeah, I know the question kinda lends itself to the response, "dumby, you need both, not one", and I realize that, but it's either get two tools that are going to be questionable performers--like your HF jointer--or get a tool that does it's job well, and will continue to do that job for a decade. Then, save for the next tool. That's why I'm leaning towards buying the nice thicknesser now and saving for the jointer. In the meantime, I have a friend that has a full powermatic workshop. For the few projects I'll do this summer, I can always joint an edge and a face then take it home to finish the rest of the project with. He lives an hour away, but I visit often. I have a 800sqft deck that I'm about to work on, so that will scratch the wood itch for a little bit as well. I am sort of kicking myself a little bit. Earlier this week, I had an opportunity to buy a dw733 and a rigid 6" jointer for $400. Might have been the best scenario to set myself up for a year or two until I upgraded. Oh well, it's spilled milk now, no sense crying. Quote
BuilderBill Posted June 7, 2014 Report Posted June 7, 2014 Haha this is true, I do not know the price required to take photos of birds at long distances. Really, if this were my only hobby it wouldn't be too bad, but I am also consumed with fly fishing(gotta have that top line gear, right?), bonsai, and Mont Blanc fountain pens. And yes, this hobby has a steep buy in cost. I would say I'm already hooked. I just love building things, so this was a natural pairing for me. You guys have helped me make my choice. I'm gonna get the dw735 and keep an eye out for a decent 6" jointer on craigslist. If a jet, grizzly, delta of decent quality pops up for $300-400, then I'll grab it. If not, then I'll save my money for a new 8" grizzly. Thankfully, these are the last two pieces of the puzzle I need for a solid workshop. I just need to be patient and make the right additions instead of getting something cheap to fill the void. I appreciate everyone's input. Oh, yeah, I forgot fly fishing, thanks for the reminder. I do that too: That's just the 3 and 4-piece rods with a couple of bamboo exceptions, the 2-piece rods occupy a corner of their own. It's a lot like woodworking though, once you have enough tools you have enough tools. So the real expense is in going somewhere to fish. Haven't bought a rod or reel in years, occasionally a new line or some leaders and flies, the big bucks go to the Yellowstone trips and others scattered here and there. I've heard you never want to fish salt, I've managed so far to heed that advice. I have Sages in 8-9-10 wt and a couple of Ross Big Game reels, they keep trying to talk me into a Florida trip but I resist the urge by going bass fishing. Kudos on your next-to-last sentence, quality beats quantity any day of the week. Best, Bill Quote
Pwk5017 Posted June 7, 2014 Author Report Posted June 7, 2014 Ok, I may have found my jointer. A 1960s powermatic 50. Apparently the guy that has it buys old tools and restores them. He's swamped so doesn't want to relaint this one, but he replaced the knives and says everything operates well. $250 for this thing. Does this sound like a good idea or a nightmare? Bill, you have far too many rods, you should send me one of those 8-9 weights : ) my 7wt g loomis is a little light for the salmon runs in New York. It makes things interesting. Quote
knotscott Posted June 7, 2014 Report Posted June 7, 2014 If it runs as he says, has new knives, and is setup well, it should be worth $250. It's worth a look anyway.... Quote
Pwk5017 Posted June 15, 2014 Author Report Posted June 15, 2014 Had a pretty good week on craigslist. Rigid 6" jointer thats a couple years old for $250. Came with 3 sets of new freud blades, and checked out to be perfectly aligned with a good fence. Then, finally got my hands on the dewalt 735. New in box 735x(extra blades, and tables) for $400. I hope to sleep easier tonight knowing that my shop is finally capable of finishing rough lumber. Time to attach the wynn canister to my dust collector and build a thien tophat. Quote
Pwk5017 Posted June 15, 2014 Author Report Posted June 15, 2014 It wasnt bad. Goes to show that if you are obsessive with CL for a few months, you WILL find what you want. I have a feeling me upgrading my jointer to an 8"+, and a cabinet saw wont be as easier, but for entry level tools like I was looking for, they do come along every so often. You just need to be the first person in line when they do! Quote
JoshC1501 Posted June 16, 2014 Report Posted June 16, 2014 I bought Grizzly's lowest price 6" jointer and a Dewalt Planer last year. I don't regret it at all, both have seen a lot of use and perform adequately. Plan to upgrade both someday but but they get the job done. 1 Quote
Bill Tarbell Posted June 21, 2014 Report Posted June 21, 2014 It wasnt bad. Goes to show that if you are obsessive with CL for a few months, you WILL find what you want. I have a feeling me upgrading my jointer to an 8"+, and a cabinet saw wont be as easier, but for entry level tools like I was looking for, they do come along every so often. You just need to be the first person in line when they do! Craigslist has some awesome deals, but as you say, the best ones tend to sell pretty quickly. I started using a little Chrome browser plugin that lets me save my CL searches when i'm on the hunt for something. It will check for updates every 5 minutes and then pop up a little alert whenever there's a new post. It works great for me since i work at a computer all day. Helped me get a Craftsman 6" jointer for $200, and an dewalt 734 planer for $150. Both were practically in new condition, which was a nice bonus. The plugin i use is called CraigsHunter, though there are other ones out there, including some for your phone. It helps to read up on how to do advanced CL searches too. Here's a search i always have being monitored to find deals on lumber in the Materials category: "rough cut" | lumber | hardwood | "hard wood" | maple | oak | cherry | board -fiberglass -window -windows -anderson -patio - laminate -doors -engineered -door Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.