Popular Post TerryMcK Posted June 12, 2014 Popular Post Report Posted June 12, 2014 I've just finished a keepsake box for my nephew and his soon wife to be. They are marrying in June 2014 so I've had to work fast on this one. The design of the box is roughly following a recent project in the WoodWhisperer Guild where Marc showed a humidor box being built. I didn't do a direct copy of this but used some of the techniques like veneering and accenting with a different wood. My wife and I also thought it would be good to incorporate some inlaying so we have chosen, with the help of one of Elly's Chinese colleagues, to have some Chinese characters in the design. This is essentially the dual happiness character used at many Chinese weddings. My nephew and his fiancée are not Chinese by the way. This is what I had to work with but it was simple to transfer to mother of pearl and cut out with a jewellers saw. I've done this many times in the past and it is very satisfying to do. It was then inlayed it into some ebony with some CA glue. The ebony was to be cut to a square shape and then finally inlayed into the box front. The box itself had to fit a regular magazine that was available on UK bookstore shelves. So the internal dimensions dictated the overall size. The outside dimensions are 370x270x160 high I also incorporated a sliding till to put small items. The hardware is all Brusso, quadrant hinges, jewellery box feet and jewellery box latch. All joints are simple rabbets and the base is plywood set into a groove. So here is the finished article in all its glory. Front view of the box showing the inlay, feet and latch. Sliding till made from mahogany, inside lined with sapele and felt baize. Hinges are Brusso quadrant hinges The finished double happiness in pearl inlayed into ebony Book matched oak burr veneer The entire box is English oak, sapele and mahogany. The veneer on the top is oak burr bookmatched in quarters making up the diamond. This is overlaid over 3/8" mdf that has sapele stabilizing veneer in the inside. The box is finished inside and out first with two coats of shellac. Onto that is pore sealer that was rubbed out to 320 grit. On top are several (12 I think) spray coats of General Finishes Enduro Var satin (semi gloss). This has been rubbed out finishing off with 0000 grade wire wool and has a nice shine that isn't too glossy. We're giving it to the bride and groom this Sunday. 6 Quote
Eric. Posted June 12, 2014 Report Posted June 12, 2014 Ebony inlaid with mother of pearl? You can't beat that. Very nice job, Terry! They'll treasure that for sure. 2 Quote
Janello Posted June 12, 2014 Report Posted June 12, 2014 Very nicely crafted, and a great gift! Terry, I've never used quadrant hinges and would love to know what technique you used for making the mortises? They came out nice and clean! Quote
Coop Posted June 12, 2014 Report Posted June 12, 2014 The top is fantastic. Heck, the whole thing is fantastic! Lining the inside w/ sapele is a good idea. I have always just cut a groove in the sides and glued a ledge for the tray to slide on. I like your idea much better. Great job 1 Quote
..Kev Posted June 12, 2014 Report Posted June 12, 2014 Super nice piece and awesome gift for the happy couple! 1 Quote
wouldwurker Posted June 13, 2014 Report Posted June 13, 2014 A fine wedding gift indeed. A cuisinart can't hold a candle to it! 1 Quote
TerryMcK Posted June 13, 2014 Author Report Posted June 13, 2014 Very nicely crafted, and a great gift! Terry, I've never used quadrant hinges and would love to know what technique you used for making the mortises? They came out nice and clean! HI Janello. There are many ways to make the mortises. Brusso sell a routing template but that is quite expensive if you are doing a few. You can also make your own shop made template using a few scraps of plywood. You can use chisels but cutting the radii is difficult. What I did was use a combination of a Dremel in a router base to hog out the waste, chisels to straighten up to my knife line and then used the Dremel to carefully shape the radii. You do need good eyesight for that so I use magnifying goggles. As I was only doing 4 mortises that was the easiest and quickest thing for me as I already have the equipment. When drilling the pilot holes for the screws either use a Vix bit or drill the holes centred towards the mortise (the radius). That way when you screw in the countersink screws the hinge pulls into the mortise. If I was batching these out I would definitely buy the Brusso routing template, a 5/16" router bit and use a regular router. One thing that you have to do is cut sufficient clearance slots for the quadrant to go - both into the carcass and the lid. Also when you fit the quadrant the ends are slightly different. The captive end needs to go into the lid. If you get it the other way around the quadrant falls out when you open the lid. I got my magnifying goggles here and Dremel base here from StewMac. Quote
RichardA Posted June 13, 2014 Report Posted June 13, 2014 Now, that's a beautiful gift, extremely well done! Quote
Janello Posted June 13, 2014 Report Posted June 13, 2014 Thanks Terry, that's some useful information. I had used standard rail hinges on my last box project because I chickened out cutting those quadrants! At the time It got me thinking, it would be nice if there was a tool designed for this, similar to a domino cutter. Albeit, it would probably be to expensive for a one-off task that's uncommon. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.