Fxguy Posted June 15, 2014 Report Posted June 15, 2014 Hello everyone! I am trying to setup a woodworking shop in my garage that is tight on space while also being tight on budget as well. I've read a few of Tauton's books as well as having taken woodshop way back in 8th grade. I've also taken precision machine tooling which introduced me to several metalorking tools including the lathe and mill. So I've been slowly accumulating tools to build a complete shop as much as possible. I'd like your advice on what I can / should do in my situation. I want to put together a shop where I can build small projects. Projects I have in mind include toys for my 9 month old (including puzzle cubes, jigsaw puzzles, building block set, etc..) as well as small jigs and maybe a workbench being the largest thing I have in mind. It would be nice if eventually I could turn pens or make jewlery boxes to generate some income down the line, but not an immediate need. I have the following tools : Table Saw - Grizzly G1022 Scroll Saw - Porter Cable PCB370SS Band Saw - Craftsman 9in Model # 137.214090 Drill Press - Craftsman 9in Model # 137.248030 Router - Ryobi R163 Jointer - Do Not Own Planer - Do Not Own Sander - finishing -- Own a Ryobi random orbit sander and ryobi palm sander, not sure of the models. So what do you suggest? Budget wise I need to stay under $400 (MIGHT be able to push to $500) but cant affoard more than that at the moment. Now I do know there are strong brand preferences, especially at my local woodworking shop (they chide and tease me about my upgrade from a craftsman table saw to a grizzly) but please refrain from such preferences here unless you have a VERY good reason why a tool should be replaced vs purchasing a tool I dont have yet. In other words please have a good reason why I should replace my craftsman bandsaw or ryobi router over purchasing a Jointer or Planer that I dont even have yet. My thoughts are that I really need at least the Jointer so that I can get a square flat edge to start with and enable me to get square cuts on the table saw as well as tight joints. So any advice / suggestions ? Thanks! Tim Quote
..Kev Posted June 15, 2014 Report Posted June 15, 2014 Welcome to the forums! We see these posts quite often so, don't think you're the only one in this situation. Ultimately, it comes down to what you want, what you need, and what your budget is. Well, you stated your budget and some of the things you'd like to do. If the tools you list are in good working order then, there's nothing stopping you from doing those projects with what you have. If you'd like to get into some bigger projects then I would suggest adding the jointer and planer to mill your own lumber. There's a lot of good choices out there at reasonable prices.. Good luck and I hope to see some of your projects! 1 Quote
wdwerker Posted June 15, 2014 Report Posted June 15, 2014 A jointer will let you clean up and square edges to be able to glue up panels. Plenty of stuff can be done without a planer but that is the next step. 1 Quote
Jim Heinbuch Posted June 16, 2014 Report Posted June 16, 2014 In my opinion, for whatever that is worth, your list of projects is on the small side.You could probably do them all with the power tools you have and maybe add some hand tools to compensate. Don't let the guys at the club raz you. If they think it is so important for you to have a better "whatever" let them buy it for you out of your budget. You have stated your budget and you must also do the other things you want to do. I get really tired of guys who look at a post that says "I have a budget for $x" and then they say the orig poster should spend more. What, didn't you read the original post that said $x? As a pastor I will end my rant with "End of sermon. Amen." 2 Quote
wtnhighlander Posted June 16, 2014 Report Posted June 16, 2014 You have as good or better selection of power tools than I had until recently. Based on that fact, I can suggest that a planer would be a very useful addition. If you get lucky as I did, you can find a previously owned Dewalt DW735 on Craigs List for $250. Or get a slightly lighter duty planer, new, for $300 -$350. The advantage for me was being able to buy rough cut lumber cheap. Making stuff from home center S4S stock is a rapidly losing proposition. Secondly, a jointer is very helpful, but if your tablesaw cuts a square, straight line, a simple sled will let you "joint" a raw edge on the saw. I didn't notice any hand tools on your list, but a decent block plane, a jack plane, and a small selection of quality chisels are worth their weight in gold. Quote
Fxguy Posted June 16, 2014 Author Report Posted June 16, 2014 First of all thank everyone for the kind responses! As luck would have it I cam across a craigslist ad for a Rigid Jointer for $175 that I'm hoping I will hear back about tomorrow. I do not have any hand tools as several of you have mentioned, so perhaps I should look into a block plane to start. Some of my troubles are that I come from a cheap Ryobi $99 table saw to start then moved up to a craftsman 10" and now to the Grizzly. Needless to say I've had a hard time getting straight square cuts. Until I got the grizzly I haven't even been able to go through a proper table saw setup. As soon as I got it I busted the lockdown on the fence and just recently replaced the part and got it fixed. I went through the setup for the fence adjustment but still seem to struggle getting straight square cuts, although its a 1000X better than the previous saws. I'm not sure if its the saw or my technique but it seems that the wood "drifts" away from the fence a little as I'm cutting. Not sure if it's the tail of the fence giving a little or if I am feeding too fast. I still need to check the blade parallelism with the miter slot but have to pick up the gauge to check that first. With a regular tape measure the blade is parallel to 1/16 an inch so thats 0.0625 inches so less than 6 thousandths of an inch which should be ok. I think its probably either feeding to fast or too much play in the tail of the fence. I'd like to put a Biesemeyer fence on it but don't have the funds at the moment. So what are some things I can do to get straight square cuts? Also thinking I need to purchase a fence for the bandsaw to help get straight square cuts with it as well. Quote
Fxguy Posted June 16, 2014 Author Report Posted June 16, 2014 Secondly, a jointer is very helpful, but if your tablesaw cuts a square, straight line, a simple sled will let you "joint" a raw edge on the saw. I didn't notice any hand tools on your list, but a decent block plane, a jack plane, and a small selection of quality chisels are worth their weight in gold. See above about some issues with my table saw, but once I get that fixed, how do I go about making the sled to help "joint" a raw edge? Quote
AndyF Posted June 16, 2014 Report Posted June 16, 2014 It sounds like your table saw could benefit from more tweaking since you're having a minor issue with rip cuts. Check out Marc's videos on table saw tune ups. Don't assume anything on your saw is square, straight, or aligned until you've proven it to yourself. As mentioned, a planer sounds like it would be a useful tool in order to work with rough lumber and different thicknesses. A router table and fence are very useful also. You might enjoy having a larger 14" bandsaw with a 1/2" blade and a 1.5-2 HP motor to do some resawing. 1 Quote
wtnhighlander Posted June 16, 2014 Report Posted June 16, 2014 A sled for straight-line ripping is simply a piece of plywood that is straight, at least on the side that runs against the saw fence. The plywood must be wide enough to support the work piece, and have a means of clamping the work. Place the work piece so that the edge hangs over the plywood on the blade side, clamp it, and run it through the saw. Remove the work from the sled, flip it around and saw rhe other edge to get two straight and parallel edges. If your blade is sharp and the saw is tuned, nothing else is needed to make those edges ready for glue up or finishing. Here js an example. These sleds are used for tapering cutsbas well:http://www.ibuildit.ca/Workshop%20Projects/Jigs/taper-jig-1.html A word of advice about saw alignment; obtain a decent dial indicator to do the measurements. A tape rule is nowhere near accurate enough. My saw is an older model Rigid contractor saw, but it is less than 1/1000" out of parallel with the miter slot and the fence. I still use the factory fence as well, as the front and rear locking style seems more stable to me. And as for the work 'drifting' away from the fence, a couple of feather boards are a must-have item for safe work at the tablesaw. 1 Quote
Fxguy Posted June 16, 2014 Author Report Posted June 16, 2014 Thank you everyone for the quick and informative / helpful replies! I must say I think I've found a new home for woodworking! I tried posting over in the forums at fine woodworking (and no offense to them) their spam filter triggered like every time I tried to post something. Anyways, thanks everyone! Quote
Fxguy Posted June 16, 2014 Author Report Posted June 16, 2014 A word of advice about saw alignment; obtain a decent dial indicator to do the measurements. A tape rule is nowhere near accurate enough. My saw is an older model Rigid contractor saw, but it is less than 1/1000" out of parallel with the miter slot and the fence. I still use the factory fence as well, as the front and rear locking style seems more stable to me. And as for the work 'drifting' away from the fence, a couple of feather boards are a must-have item for safe work at the tablesaw. Any suggestions on a Dial Indicator? The factory fence on the Grizzly isn't "bad" as far as I can tell. Just think it may need some more adjustments. Not sure that its a front and rear locking style though. Perhaps it is an I'm just not that familiar with fence styles to know. Its supposed to "square" to the blade slot opening when locked 2/3 of the way (at which point the rear C part should be touching the rail) and have it very close, think maybe I just need to work on tweaking it a bit more. I have a crosscut sled, but don't have a sled for cutting along the length of a board. I do have a couple of feather boards but haven't used them. I think it's time I start to break the horrible habit of skimping and cutting corners on setups because I'm impatient and it takes time to do. Quote
Fxguy Posted June 16, 2014 Author Report Posted June 16, 2014 It sounds like your table saw could benefit from more tweaking since you're having a minor issue with rip cuts. Check out Marc's videos on table saw tune ups. Don't assume anything on your saw is square, straight, or aligned until you've proven it to yourself. As mentioned, a planer sounds like it would be a useful tool in order to work with rough lumber and different thicknesses. A router table and fence are very useful also. You might enjoy having a larger 14" bandsaw with a 1/2" blade and a 1.5-2 HP motor to do some resawing. Andy, thanks for the link! Going to check it out as soon as I have some time. As for a router table and fence, I do have Ryobi's table and fence that come with the table, currently mounted on a mobile cabinet top so it slides onto a mobile cabinet base anytime I need it. I'm currently finishing up working on a Mobile routing and sawing center for my table saw and router to increase the surface area I have to work with while saving on space in the garage. Its the plans I got from here : http://www.woodstore.net/mosaroce.html I'm thinking once it's finished I may have to upgrade my router to one that will work with a router lift insert that I have still yet to purchase for that table. 1 Quote
wtnhighlander Posted June 16, 2014 Report Posted June 16, 2014 I use a dial indicator from Harbor Freight, but HF quality can be suspect. You can order indicators at a similar price from places like Mcmaster-carr or Grainger. Look at Matthias Wandel's site (woodgears.ca) to see the indicator jig he uses for blade alignment. I patterned mine after his. See it in use here:http://woodgears.ca/table_saw/fence_micro.html Also, Steve Ramsey, at woodworking for mere.mortals on youtube, just posted a video about using a sled to edge-joint boards on the tablesaw. Jig for edge jointing on a table saw | Mere Mini …: http://youtu.be/vrYjc3G1vgo Quote
Fxguy Posted June 16, 2014 Author Report Posted June 16, 2014 Ok, so I got a dial indicator today, brought it home and noticed a few things about my saw. First off, while making a jig to hold the dial indicator in the miter slot, as I was sanding the slot piece of wood to be flush with the table top, I noticed that there is quite a bit of rust on the top. Not unusable, but the surface needs a good sanding to remove the surface rust and bring back the shine and smooth as glass surface of the cast iron top. Not a bad thing, just needs some elbow grease! Secondly, I measured a tooth of the blade in front and back and got 0.230" for the front reading and 0.243" for the back reading, so what is that, a difference of 0.013" or 13 thousands of an inch if I'm not mistaken. Thats more than the 0.004" the manual calls for so I guess I have some adjusting to do! I'll let you know how it goes! Quote
..Kev Posted June 16, 2014 Report Posted June 16, 2014 Measure the same tooth each time. Put a mark on the tooth you measure on the front of your saw and then rotate the blade to measure the same tooth on the back of your saw. If the blade varies from tooth to tooth that will throw your measurement off. Quote
AndyF Posted June 17, 2014 Report Posted June 17, 2014 Andy, thanks for the link! Going to check it out as soon as I have some time. As for a router table and fence, I do have Ryobi's table and fence that come with the table, currently mounted on a mobile cabinet top so it slides onto a mobile cabinet base anytime I need it. I'm currently finishing up working on a Mobile routing and sawing center for my table saw and router to increase the surface area I have to work with while saving on space in the garage. Its the plans I got from here : http://www.woodstore.net/mosaroce.html I'm thinking once it's finished I may have to upgrade my router to one that will work with a router lift insert that I have still yet to purchase for that table. That sawing/routing center looks useful. I've never used a router lift, but I don't see much of a need for one. There are routers designed to adjust the bit from above the table. I get by with a plunge router and the spring removed for now. The Bosch 1617EVS has a new fixed base which allows above-table adjustments, and that's what I plan to get. Quote
Fxguy Posted June 17, 2014 Author Report Posted June 17, 2014 That sawing/routing center looks useful. I've never used a router lift, but I don't see much of a need for one. There are routers designed to adjust the bit from above the table. I get by with a plunge router and the spring removed for now. The Bosch 1617EVS has a new fixed base which allows above-table adjustments, and that's what I plan to get. I'm hoping it's useful! The Ryobi router I have adjusts from above the table, so maybe I just need a plate for it and I can get by for now. Quote
Fxguy Posted June 17, 2014 Author Report Posted June 17, 2014 Well I guess my table set up and restore is going to have to wait for now. I tried loosening the rear two trunion bolts and adjusting but the closest I can get is 0.008" front to back variance. Also noticed that my dial indicator jig is not steadfast and so I'm going to get the magnetic base for it. Problem is with the Grizzly that I have the adjustment instructions involve removing the motor, wings, and sheet metal surround then turn the saw upside down to access the trunion underneath the table. Due to the weight looks like I'm going to have to wait until a friend can come assist me with squaring up the blade to the miter slot. What do you guys think? Is 0.004" or less pretty good and accurate to get square cuts? Quote
wtnhighlander Posted June 17, 2014 Report Posted June 17, 2014 4 thou is certainly better than 13, but I'd bet you can get it a mite closer. Tedious work, but well worth it in the end. O, and don't obsess too much of rust stain on the table. As long as it is smooth and flat, discoloration won't hurt anything but your sensibilities. Clean off the surface, rub on some paste wax and buff it slick. Quote
knotscott Posted June 17, 2014 Report Posted June 17, 2014 Once you get it that close, sometimes it's just easier to fine tune that last couple of thousandths by adjusting the fence instead of the trunnions. Quote
Fxguy Posted June 17, 2014 Author Report Posted June 17, 2014 Once you get it that close, sometimes it's just easier to fine tune that last couple of thousandths by adjusting the fence instead of the trunnions. I plan on getting it as close as possible. I've never truly done a setup of a saw, so this will be an experience. Hope to get the trunnions as close as possible and then fine tune the fence as well. Needless to say after working with the Ryobi $99 table saw where the table was maybe 18" and now working with the grizzly the quality has improved tremendously. One I'm done with the setup this will be the best quality cuts I've been able to get ever. Anyone have any opinions on a good Table Saw book? I love books and learn from them quite easily if they are well written and illustrated. I was thinking about the Tauton publishing Table Saw book. Any thoughts? Or maybe some DVD's on woodworking and tool setup might be a little more suited to my novice needs? Quote
knotscott Posted June 17, 2014 Report Posted June 17, 2014 The Table Saw Book by Kelly Mehler is excellent. So is Table Saw Magic by Jim Tolpin. Quote
Fxguy Posted June 17, 2014 Author Report Posted June 17, 2014 The Table Saw Book by Kelly Mehler is excellent. So is Table Saw Magic by Jim Tolpin. Thanks! Really like the Kelly Mehler book, at least from the preview available on Amazon. Looks very thorough! Quote
knotscott Posted June 18, 2014 Report Posted June 18, 2014 I'm paraphrasing, but a well respected woodworker who frequents many of these wwing forums told this story a few years back....AFAIK, it's true. "Dave" had been shopping for a table saw, had done his research, and was feeling pretty confident when a Ridgid contractor saw came up for sale in his area. He went to look at it, liked it, looked it over very thoroughly, then proceeded to point out reasons that it wasn't worth the full asking price to the owner. The owner accepted a counter offer from Dave, and agreed to accept a personal check from him. When asked who the check should be made out to, the owner replied "Kelly Mehler"! Dave bought the saw that's featured on the cover of Kelly's book! I about spit coffee on my PC when I read that story from Dave. Quote
Harrington Posted June 18, 2014 Report Posted June 18, 2014 From the sound of things you are doing everything right and that is giving each purchase very careful consideration. It sounds as though you are thinking of a jointer as your next major purchase and a jointer is a very good tool for a complete shop. However to get a nice straight and square edge on a piece for gluing or whatever you can also use a router table with a offset fence. I admit a jointer would do a quicker job but with proper set up I don't think it would be any better. A router table also is a very versatile tool and can open up a lot of other options. With budget and space restrictions it could very well be less expensive and take up less room. U-Tube is full of very good suggestions for shop built router tables. Good luck in your future with wood working. It is a great way to spend your time and as your experience grows so will the satisfaction you get from it. Dave Harrington Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.