Recommended Posts

Posted

They seem to be all the rage. Every video I see of a dude cutting a mortise, he uses a Forstner bit to remove the initial material before he switches to chisels.

Now, from what I understand, the purpose of a Forstner bit is to drill a flat-bottomed hole. Is the flat bottom really that important when making a mortise?

Are there other advantages over the ordinary lip and spur bit that makes it more suitable for that task? I don't know, I just can't imagine that the holes left by the brad point at the bottom of the mortise would compromise a mortise and tenon joint in the slightest.

Posted

Most forstners have a brad point, too, so that's not really an advantage.  And no, the little holes don't compromise the joint.  You can use any bit you want to waste out a mortise, but the advantage of a forstner is making a clean, flat-bottomed hole in larger diameters.  They remove waste quickly and tend to stay cooler while they do it.

 

That said, I never use a drill bit to waste out a mortise...tends to be too sloppy for my taste, though it does work.  I prefer a router and straight bit most of the time.

Posted
Aha, thanks. It looks like another advantage might be that it is better at cutting overlapping holes.

That said, I never use a drill bit to waste out a mortise...tends to be too sloppy for my taste, though it does work. I prefer a router and straight bit most of the time.

I've wondered about this. A router just seems like a better tool for the job, yet most videos and discussions I'ev seen uses a drill press to remove material. Do you use a plunge router or a router table? I'd imagine you would cut deeper in increments as you can't plunge the bit its full length and then cut sideways? You wouldn't have a link to a video or articles or something that explains your technique?
Posted

You can use a plunge router or the router table.  I prefer the plunge because I'm not a huge fan of dropping and lifting pieces on the table.  I've done it many times without problems, but it induces some pucker.  Yes you make several passes at increasing depth.  I'll see if I can dig up a couple of Marc's free videos...I'm sure there's several that show him using both techniques.  Hold please...

 

Plunge technique starts around 7:40...

 

http://www.thewoodwhisperer.com/videos/sitting-bench-step-stool-pt-1/?category_name=marcs-projects

Posted

You can use a plunge router or the router table.  I prefer the plunge because I'm not a huge fan of dropping and lifting pieces on the table.  I've done it many times without problems, but it induces some pucker.  Yes you make several passes at increasing depth.  I'll see if I can dig up a couple of Marc's free videos...I'm sure there's several that show him using both techniques.  Hold please...

Cool bananas. Don't bother. I found this one and its part 2. Tells everything I need to know.

 

 

Or you could get a domino....just saying ;)

I was waiting for that one. Somehow I still think a Forstner bit works out a bit cheaper :)

Posted

I've found that even with a drill press & fence using a forstner bit to hog out the waste there is still lots of cleanup required.

 

If you are buying forstner bits, you want to get the high speed steel as opposed to carbon steel.  The cutting edge isn't ruined by heat nearly as easily.  Most I've seen are carbon steel, but Lee Valley sells a high speed steel set.

Posted

Unlike other bits a Forstner bit is guided by its circular rim and not by the centre point. It will bore any arc of a circle and its direction is unaffected by knots or the run of the grain. The holes bored are flat-bottomed, true and clean. You can also bore overlapping holes without difficulty.

  • Like 1
Posted

Unlike other bits a Forstner bit is guided by its circular rim and not by the centre point. It will bore any arc of a circle and its direction is unaffected by knots or the run of the grain. The holes bored are flat-bottomed, true and clean. You can also bore overlapping holes without difficulty.

As long as you use it in a drill press, anyway. Forstners are notoriously difficult to keep straight in a hand drill. On the flip side, you can actually bore a curved hole with one, if necessary.
  • Like 2
Posted

Or you can make a "router press", aka a pantarouter, ala Matthias Wandel: http://woodgears.ca/pantorouter/xl.html . That thing excels at cutting mortices AND tenons. I enjoy the hand work of joinery too much to bother building one, but that thing is slick!

 

I think his slot mortising machine is better for this, no need for building accurate scale guide templates, for both the mortise and tenon then.

Posted

Yes, for a purpose-built machine.

I have some ideas of combining that with a tilting table like the one Stumpy Nubs made for raised panels could be a useful maching.  After all if you lock the Y axis you have a basic horizontal router.  And micro adjustable stops feels like it gives more easily attainable accuracy.  Of course some of that might be it conforms to my expectations of how cutting machines work from working in a metal stamping company.

Posted

Aha, thanks. It looks like another advantage might be that it is better at cutting overlapping holes.

I've wondered about this. A router just seems like a better tool for the job, yet most videos and discussions I'ev seen uses a drill press to remove material. Do you use a plunge router or a router table? I'd imagine you would cut deeper in increments as you can't plunge the bit its full length and then cut sideways? You wouldn't have a link to a video or articles or something that explains your technique?

YouTube new Yankee workshop how to use a router. He goes over a ton of info. Not sure if it's video one or 2 that he talks about your issue though. Just watch it all cause it is time well spent :D

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 47 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined