wtnhighlander Posted December 4, 2014 Report Posted December 4, 2014 I had thought about the shelix upgrade for my dewalt a couple of times, but I could never justify putting that cutter head on that machine when it costs about as much as the machine itself. Womp Womp Freddie, when I looked last week, shelix heads for the 735 could be found for $410. That's only about 3/4 the cost of the machine. What a bargain! 1 Quote
Freddie Posted December 4, 2014 Report Posted December 4, 2014 Freddie, when I looked last week, shelix heads for the 735 could be found for $410. That's only about 3/4 the cost of the machine. What a bargain! In that case, the left over savings can put some spinners on the mobile base and make the whole thing even more ridiculous! 2 Quote
Vyrolan Posted December 4, 2014 Report Posted December 4, 2014 In that case, the left over savings can put some spinners on the mobile base and make the whole thing even more ridiculous! Clearly it needs a sound-triggered laser light show to dazzle you as the boards pass through. 1 Quote
Freddie Posted December 4, 2014 Report Posted December 4, 2014 Clearly it needs a sound-triggered laser light show to dazzle you as the boards pass through. -It needs a laser light on the mobile base so you know where the base will land once you drop the 3rd wheel. -Or: dual in feed and out feed lasers to show a clear path and work around any obstructions in the shop. Quote
Vyrolan Posted December 4, 2014 Report Posted December 4, 2014 I dig the way you do business Freddie. Quote
RichardA Posted December 4, 2014 Report Posted December 4, 2014 Oh wow. Like it that much huh? Then that seems like a definite top couple on the list for planers Is the dewalt pretty much a unbox and go or does it have a long setup time? Set up time is as long as it takes to plug it in!... However, adjusting the in and out feed tables should be a priority, to eliminate or cut down on snipe... That only takes a minute or two! Quote
RichardA Posted December 4, 2014 Report Posted December 4, 2014 I always thought dead nuts was a reference to all the old guys that you find on woodworking sites ! < evil grin > Hey... I resemble that remark!!!!! Quote
pghmyn Posted December 4, 2014 Report Posted December 4, 2014 If it were my money, I would go with the Grizzly floor standing unit. You said you have the room, so that isn't a problem. If you have time to wait, maybe a 10% off Grizzly coupon will pop up somewhere for you. Or, you can do exactly as I did with my big purchase - although not favored by many people. I planned on purchasing my G0715P, and G0656P at the same time. Little over $2,000 in purchases including freight. I had a 10% off coupon at my disposal, but I also remembered getting a credit card offer in the mail. $100-$150 (can't remember which) cash back if you spend $500 in the first 3 months. Plus, 1% cash back on top of that. So, that was about $120-$170 additional off the cost. I had the cash, paid the card off in full once the bill came, bingo bango - saved more money! I actually kept the card and I still use it as a dedicated gas card. This card has rotating cash back categories and usually 6 months of the year is 5% cash back on gas. By year end, I usually get about $100-$150 cash back total. Works for me, it's set to auto-pay to take out what I spend in the month. Just another option to save you some money Quote
ottacat Posted December 4, 2014 Report Posted December 4, 2014 I used to own a General International 6" dovetail jointer and it was awful. I was never able to get it adjusted and it never was able to joint a board properly. It was a truly frustrating tool to own. It was also too small. When I bought another jointer I bought a Busy Bee 8" parallelogram straight knife jointer (Busy Bee is a Canadian company owned the brother of the owner of Grizzly and sells essentially the same machines). I set it up following Marc's video which required also buying a long straightedge and feeler gauges. The setup was a bit frustrating but I got it done and it works beautifully. I would never buy less than an 8" jointer again. If I had more money at the time I would have bought the helical head version. When my blades get dull I'll probably switch to ESTA. The end result will be a bit more $$$ than having bought a helical head in the first place but I had limited financial resources at the time. I've had the jointer 1 1/2 years so far and the existing knives are still quite sharp. I could also upgrade to a helical head but the ESTA solution is simpler, less expensive and I don't use much figured wood and noise isn't really an issue. For a planer, I didn't want a 15" planer with traditional knives. It was either the 735 DeWalt or a 15" with helical head. The cost difference between the two was quite large so I went with the 735 and got a package that included the stand, a spare set of knives and the extension tables. So far it has worked beautifully. Again 1 1/2 years in I'm still on the first set of knives but I'm just a hobby woodworker. So I got both machines for < 2k and they work great for my volume of use. I considered the Hammer 12" jointer / planer as it has a good reputation and the extra jointing width. However its cost was over twice what I paid and I needed the other money at the time for other tools. I also enjoy having two separate machines that I don't have to change over. Our shops and tools are also part of this hobby and what we buy is often beyond our realistic practical requirements given the volume of work we do as hobby woodworkers and the fact that our time isn't measured in dollars as is a commercial woodworker. To me an 8" parallelogram jointer and 735 were a great functional start and I'm still quite happy with them. Quote
bushwacked Posted December 4, 2014 Author Report Posted December 4, 2014 ya i signed up for their emails ... hoping to get one of the 10%. also hoping the christmas sale TIODS keeps mentioning is worth it, or at least on the tools I am wanting. the CC thing is a nice. Although, the CC I want does not offer that $100 back. I will get the 1% cash back off my CC and I already have some cash back $$ I can use toward the payment as well. Quote
pghmyn Posted December 4, 2014 Report Posted December 4, 2014 ya i signed up for their emails ... hoping to get one of the 10%. also hoping the christmas sale TIODS keeps mentioning is worth it, or at least on the tools I am wanting. the CC thing is a nice. Although, the CC I want does not offer that $100 back. I will get the 1% cash back off my CC and I already have some cash back $$ I can use toward the payment as well.Again, probably not advised, but you could find a reputable one that does offer the lump sum cash back following a certain purchase amount. If you don't want to keep it, cancel it. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.