Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Candle holder... The perfect gift I was trying to figure out

Featured Replies

My one-day finish for stuff as big as say, a coffee table:

Cut Bullseye sealcoat by 50% with alcohol. Apply with a clean cotton rag, wiping it so as to leave no runs. Wait 5 minutes and re-apply. Repeat until there is a consistent, but barely noticeable film, usually 3-4 coats. Wait 30 minutes, scuff lightly with 320 - 400 grit paper. Remove dust with a tack cloth. Wipe on a thin coat of wiping poly, and I mean something like Minwax poly cut by 40% or so with spirits. Allow to dry overnight. Avoid heavy use for another day or two, if possible.

The shellac is suoer fast to seal the wood and build a slight film, then one coat of poly provides wear and spill protection. Certainly not as much as using poly from bare wood, but doesn't take a week, either.

  • Replies 60
  • Views 9.5k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Slick as a ribbon.... nice job!

  • If you do manage to get a Forstner bit of the right size use it to make a routing template. Otherwise if you just use the Forstner to make the recess you will be left with a location hole in the centr

  • Yes I'm with Eric. I would guide the piece with paddles (I value my fingers too much) on the router table only after removing the most waste I could. There is a likelyhood the piece could grab and spl

  • Author

After the first one received a beat down I made another one. This time to level the feet I went to woodcraft and leveled it on their 10" disc sander. I then bought a 10" disc/belt sander before I left.

 

Round 2 Candle holder almost finished. First coat of Arm R Seal top coat on it. This stuff goes on so easily.

 
 
IMAG2264.jpg
  • Author

Just put on the second coat of Arm R Seal. Hit the first coat lightly with 320 grit. Shop is sitting at 78 degrees (it's miserable in there) I sweat just thinking about it. Third and last coat will be thinned per Eric's recommendation and brushed on with a foam brush. I won't have 2 days to buff with wax. I'm giving it as a gift Wednesday night. 

 

Cure time is 2 weeks, so I won't have a chance to buff it out. 

With respect, why?

 

Should be smooth as a baby's bottom without the wet sand and be a perfect gift.  

  • Author

With respect, why?

 

Should be smooth as a baby's bottom without the wet sand and be a perfect gift.  

 

I just realized wet sand would be after it cures, I won't have time for that so no wet sanding will happen. I usually wet sand finishes to make them smooth. I've never worked with Arm R Seal. I'm looking forward to seeing how it comes out.

You'll be fine for a gift..  I'm quite sure the finish will be better than anything they own.

Just put on the second coat of Arm R Seal. Hit the first coat lightly with 320 grit. Shop is sitting at 78 degrees (it's miserable in there) I sweat just thinking about it. Third and last coat will be thinned per Eric's recommendation and brushed on with a foam brush. I won't have 2 days to buff with wax. I'm giving it as a gift Wednesday night. 

 

Cure time is 2 weeks, so I won't have a chance to buff it out. 

 

I'd put that third coat on with an old shirt made into a pad.  A foam brush is gonna be too wet and you'll run the risk of leaving drips.  It's kind of defeating the purpose of the thinned final coat...you want it thin, just so it covers up the scratches from the previous round of sanding.  It will dry faster so fewer nibs will settle on the surface.  I apply my first coat with a foam brush...but only the first coat.  You have a lot more control with a fat wad of cloth barely wet.  Thin, light, even strokes.

  • Author

The thinned stuff dried with the quickness. Faster than shellac! I noticed a couple of little drip spots from the second coat. Lesson learned, second coat is not brushable.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.