dwacker Posted December 23, 2014 Report Posted December 23, 2014 Not really power tool but I have a bunch of cutters that have been sitting. Now that I'm taking them out to organize and use I'm finding they are all magnets. Its making it difficult to get them aligned in the head. Anyone have a way to cure this without heat or a hammer? Thank you These are an example. They are all HSS. Quote
Beechwood Chip Posted December 23, 2014 Report Posted December 23, 2014 Try holding them next to a spinning electric motor (the biggest one you can find), and then slowly move them away a few feet. If the magnetic field put out by the motor is strong enough and "rapidly fluctuating", then this will work. 2nd idea: Take a powerful magnet and attach it (hot glue will work) to something that spins, like a drill bit. You want to spin it so that the north-south orientation of the poles is changing when it spins. While it is spinning, hold the cutter close for a minute then slowly move it a few feet away. Quote
dwacker Posted December 23, 2014 Author Report Posted December 23, 2014 I think the motor is what caused the issue. They were sitting in a wooden box on top of a 20hp rotary air compressor for almost 6 months. Quote
Llama Posted December 23, 2014 Report Posted December 23, 2014 Not ideal, but you could heat them up a bit. Quote
tim0625 Posted December 23, 2014 Report Posted December 23, 2014 Not ideal, but you could heat them up a bit. And hit them with a hammer. I know how to build a magnetizing apparatus which could be used in reverse to demagnetize, but I don't know if it would work for this. Try the other suggestions first. That cat that was on WTO would know....the guy who built his own rotary phase convertors....can't remember his name. Quote
TerryMcK Posted December 23, 2014 Report Posted December 23, 2014 A tape head demagnetizer will do it. http://www.amazon.com/Universal-DEMAGNETIZER-Cassette-Recorder-Track/dp/B003ZKLP4W Just don't hold it near any of those old 1970s 8 track tapes you have. And keep it away from your computer hard disk. These things demagnetize anything. Quote
drzaius Posted December 24, 2014 Report Posted December 24, 2014 Do you have a soldering gun (not iron), the kind that uses a heavy copper wire type tip? If so, you can take about 2' of 14 ga. copper wire & form it into a loop with 3 or 4 turns. Then remove the tip from the soldering gun & connect the loop in its place. Pull the trigger on the gun & slowly pass the cutter head through loop. The AC current generates an alternating magnetic field that will remove the magnetism in the cutter. Done it lots of times & it's very effective. 2 Quote
Beechwood Chip Posted December 24, 2014 Report Posted December 24, 2014 As I recall, the trick is to slowly move the item out of the field before shutting the field off. If you shut off the field while the item is in it, it might keep whatever orientation the field was in when it was shut down. And if you remove the item too quickly, it might keep whatever orientation the field had just before the item was removed. Maybe in practice it doesn't matter, but that's what I was told. Quote
dwacker Posted December 24, 2014 Author Report Posted December 24, 2014 Thanks guys. I think I found the answer. I noticed while separating out the knives that the ones with red templates didn't turn into magnets only the knives with the white templates. The red ones are ground knives and the white ones are cut on a water jet. I'm no scientist but just taking the water jet knives over to the blade service and having them lightly sharpened took care of the problem I have no clue why but it worked or why ground knives didn't have the same issue. Thanks All Sent from my iPhone using Tapatalk Quote
Firehawk Posted December 24, 2014 Report Posted December 24, 2014 The blade service likely has a demagnetizer that they run them through after sharpening them. Quote
dwacker Posted December 24, 2014 Author Report Posted December 24, 2014 The blade service likely has a demagnetizer that they run them through after sharpening them. No he said it had something to do with the grinding vs water jet. Just a little grinding to sharpen got rid of the problem. Sent from my iPhone using Tapatalk Quote
wtnhighlander Posted December 24, 2014 Report Posted December 24, 2014 Maybe the waterjet uses a magnetic table to hold the work while cutting? Grinding may work a bit like pounding with a hammer to disorient the magnetic fields at a molecular level? Just guessing. Quote
tim0625 Posted December 25, 2014 Report Posted December 25, 2014 Do you have a soldering gun (not iron), the kind that uses a heavy copper wire type tip? If so, you can take about 2' of 14 ga. copper wire & form it into a loop with 3 or 4 turns. Then remove the tip from the soldering gun & connect the loop in its place. Pull the trigger on the gun & slowly pass the cutter head through loop. The AC current generates an alternating magnetic field that will remove the magnetism in the cutter. Done it lots of times & it's very effective. That was what I was referring to....just doing it with a light bulb Quote
drzaius Posted December 26, 2014 Report Posted December 26, 2014 Chip: That is exactly right, I just didn't explain clearly Tim: The loop completely surrounds the object with the alternating magnetic field & using a soldering gun provides a very high current & therefore a strong field. Quote
tim0625 Posted December 26, 2014 Report Posted December 26, 2014 Chip: That is exactly right, I just didn't explain clearly Tim: The loop completely surrounds the object with the alternating magnetic field & using a soldering gun provides a very high current & therefore a strong field. That's right...Most of mine just magnetize a screwdriver shaft so a few loops do it. It's interesting to read about creating an electromagnet...really easy but I don't know what the heck I'd use it for. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.