Recommended Posts

Posted

I know I have another one of the bandsaw posts but figured this deserved it's own in case someone has the same issue it will be easier to find.

So I tried to veneer a few strips for my new project. Will be posted in the project section shortly.

Anyways I have a slight tilt in the cut from top to bottom. I thought I have leveled it decently but I guess I can't go off the level? And just need to keep tweaking the surface plate?

18cb4c657430de521ffe343f9867f3fb.jpg

55ece9f1c9e4dd500995f5db36bf83a2.jpg

6193cccafb50cfe505d88d3151f8d6ab.jpg

Posted

Table needs to be 90 degrees to the blade. Fence needs to be 90 degrees to the table. If either of those are out you're gonna get that tilt. Loosen your tilt lock and adjust the table tilt until your square shows no gap between the blade and the square face. 

  • Like 1
Posted

Have you checked the 90 degree stop under the table to make sure it can reach 90?

Table needs to be 90 degrees to the blade. Fence needs to be 90 degrees to the table. If either of those are out you're gonna get that tilt. Loosen your tilt lock and adjust the table tilt until your square shows no gap between the blade and the square face.

Ok thanks!!

Going to give it another go after lunch

Posted

There should be a bolt or some sort of screw sticking up from the frame of the saw that the table comes into contact with when you tilt it and then return it to the 90 degree position.  Most likely it will also have a locking nut on it so that once it's set to 90 you can return there every time (or very close) without having to do the trial and error thing.  The gauge is probably not going to be accurate - parallax error alone is enough to make you ignore it. 

Posted

I does help to joint a really flat bottom and 90 degree face before you start cutting thin veneers on a bandsaw. Table , fence and blade still need to be square but if the block you are cutting from is wobbling the cut will be off.

  • Like 2
Posted

I does help to joint a really flat bottom and 90 degree face before you start cutting thin veneers on a bandsaw. Table , fence and blade still need to be square but if the block you are cutting from is wobbling the cut will be off.

 

Good point. I was just assuming that he had milled the board.

  • 4 weeks later...
Posted

This thread is pretty old, but I never trust the stops or angle gauge. I just set the table with a square against the blade each time the table moves, or the machine moves (tugging on the table moves it out of whack)

  • Like 1
Posted

I've seen this and like the idea but it really should be said that the test piece should be at least 3-4" tall to give you a good reference

i would assume the taller the better, using a full height piece should make your saw crazy accurate?
Posted

i would assume the taller the better, using a full height piece should make your saw crazy accurate?

I'd also keep it close by to check often if you move your saw. I roll my saw forward from the wall about 8 inches to use it and I guess that little movement kicks the table out of square often. I have to level it about every two weeks

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 43 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined