Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Upgrade Dewalt 735 or go for PM 15HH Planer?

Featured Replies

I got to ask, why keep a spare cutter head? 

 

His great-grandson will finally use up the 4th side of the helical inserts, and then what's he supposed to do?!?!?!

I got to ask, why keep a spare cutter head?

its a good spare, in-case something goes wrong with the byrd. I know a guy who did this, and when he had to plane down a few thousand bf or re-claimed barn lumber he put the old head back in, so he didn't have to check every single board for metal or risk damaging his helical head.

its a good spare, in-case something goes wrong with the byrd. I know a guy who did this, and when he had to plane down a few thousand bf or re-claimed barn lumber he put the old head back in, so he didn't have to check every single board for metal or risk damaging his helical head.

 

 

Exactly.  Stuff happens.  cutters chip or get dull.  Even on the carbide heads you need to flip the cutters around from time to time.   You could mount the spare and use it until you get a chance to turn the carbide cutters around.     But the main point is, most people agree the byrd is better than Grizzly's knock-off.  So get the straight knife planer and buy the Byrd.  it is a better deal, even if it costs an extra $50 or so.  

Exactly.  Stuff happens.  cutters chip or get dull.  Even on the carbide heads you need to flip the cutters around from time to time.   You could mount the spare and use it until you get a chance to turn the carbide cutters around.     But the main point is, most people agree the byrd is better than Grizzly's knock-off.  So get the straight knife planer and buy the Byrd.  it is a better deal, even if it costs an extra $50 or so.  

 

I keep my Shelix heads for some reason that I haven't figured out quite yet. The grizzly is a kin to the PM but the one that was closer was the extreme series that they don't sell any longer. They were about $500 more expensive and are still that for the 20". For $500 your getting better service, and 4 years extra warranty. With the PM it usually pretty easy to get free shipping which puts you at about $350 apart for the warranty and service. One thing Grizzly can't compete with is WM service and warranty.

I'm in western NY. Not sure what the shipping cost would be. I assume you wouldn't want to come pick it up.

Wasn't sure where you were at. Probably not going to New York anytime soon. Would love to have a nice planer like that though.

its a good spare, in-case something goes wrong with the byrd. I know a guy who did this, and when he had to plane down a few thousand bf or re-claimed barn lumber he put the old head back in, so he didn't have to check every single board for metal or risk damaging his helical head.

 

Well I guess but I can't see doing it. 

  • Author

Thanks to all for your help. I sold the 735 this morning and ordered the PM 15hh this afternoon. 

Thanks to all for your help. I sold the 735 this morning and ordered the PM 15hh this afternoon.

Good choice. I got my 15hh a couple days ago. Set up to a 30 amp breaker. It it very quiet and the finish is amazing. Definitely produces snipe though. I havent had a chance to play around with any adjustments yet though. I also realised that i didn't lock down the table which might help a bit with the snipe. If i cant get the snipe eliminated completely then a pass or two through the supermax should remedy that so im not overly concerned.[emoji1]

I rarely get snipe and it's been a while since I put my planer together. IIRC my rollers are barely above the table and infeed/outfeed table ends are a little higher than main table.

I rarely get snipe and it's been a while since I put my planer together. IIRC my rollers are barely above the table and infeed/outfeed table ends are a little higher than main table.

Do you also have the 15hh? I will follow your recommendations. The manual says .006" above the table for the rollers. Are yours even lower than that? I have some time to play around with tuning this weekend so i will try to get it snipe-less!

I have the Shop Fox 15" which is the Grizzly twin brother. I'll check the measurements this weekend. Remind me if I forget.

Snipe – Resistance is Futile!   :)

 

 

There are some who adjust their way to a snipe-free existence, but I suspect they inhale a little too much solvent lacquer... It’s true that some individual planers consistently produce snipe-free stock, but I’d bet these are less than 1%... If you want to spend north of $15K, we can talk snipe-free (much of the time)… But for most, a little snipe is the norm… If you can’t adjust your way to snipe-free milling, just be happy you're not planing by hand… Leave your stock a little long and use the off-cuts to test your finishe schedule…

 

If you don't have an extra $15K or $20K sitting around... Get yourself a drum sander, then you won't care about snipe...

 

 

Always remember: Death... Taxes... Snipe...

The bed roller height adjustment is for milling rough stock. Generally with face jointed material they are level with the bed. Waxing the beds helps more than anything else. Wax the bed when you think they are slick and nicely waxed wax them again.

If my planer didn't snipe, what would I use in my smoker?  

BTW: the one workflow that largly eliminates snipe is to feed the stock line a railroad train – one stick right on the heels of the next… If you use a sacrificial stick on the front and one of the back of the train (locomotive and caboose), the keepers in the middle will be snipe free…

BTW: the one workflow that largly eliminates snipe is to feed the stock line a railroad train – one stick right on the heels of the next… If you use a sacrificial stick on the front and one of the back of the train (locomotive and caboose), the keepers in the middle will be snipe free…

Ya i always did the choo choo train. But that was with my old dewalt 735 and 20" general planer. Thought the powermatic might be able to be tuned in to have no snipe. I do have the supermax 19-38 so the 3" of snipe on either end will disappear. ....i can live with a little snipe

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.