Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Shop Light Layout

Featured Replies

Any strong opinions on how I should layout my shop lights before I hang them tomorrow?

Option A

83413b062b12a92a7822e6a93c8c1432.jpg

Option B

04a8b3bed8c9f2bb2629495b732011c2.jpg

Sent from my iPhone using Tapatalk

If they're halfway to scale, I'd say 8'.

Probably the reason I don't win at roulette. If I bet black, it will be red!

I'd opt for "A"

  • Author

Haha. Not even close to scale. I was over exaggerating the light size in the drawing because I was texting a pic to my father in law.

Sent from my iPhone using Tapatalk

That's a tough one. If you go with option 1 you're gonna get shadowing on the long walls. If you go with B you might get some dim areas.

If you will have work areas along the long walls, then perhaps dedicated lighting for that area?

Option C might be your ticket! Don't know your fixture but if this one is close 110 FC is good lighting!

post-8178-142690552309_thumb.jpg

Is the ceiling rocked? Can you move them later after the tools are located if need be?

I'd be tempted to hang them temporarily until you get the shop layed out like you like it or be prepared for shadows as Tom mentioned.

  • Author

Ceiling is already closed in, I'll be running the electrical in flex conduit. Other than the hassle of moving them, it'll be easy to move them later.

161b2bq.gif

Put the 4 fixtures end-to-end down the middle of the space - with tube lamps the light comes out the sides, not the ends - what this will do is put the majority of the light over the most used work surfaces of the tablesaw and work benches, plus with 4-tube fixtures and a 14' mounting height you'll still get plenty of light bouncing off the walls and ceiling to minimize shadows.

Any specific reasoning why you went with 4-tube fixtures? If I was doing it, I'd go with 4' 2-tube, 8 fixtures, end-to-end in two continuous rows mounted 4' out from the long walls.

Either way, I think with such a small space, you're going to have enough light, maybe even too much to the point where it's uncomfortable to work in, but you can always take out a tube or two in each fixture to get the light level where you want it.

Tony

--

BYW, here is my shop following that tool. At first I didn't agree with it but very happy that I followed it.

post-8178-142691090672_thumb.jpg

I'm a little lukewarm about the T5 bulbs.  They're super bright, which is awesome...but they kind of make me feel like I'm made of plastic when I'm under them.  A very artificial feeling light (I do have "low" ceilings - 10 feet - if that makes a difference).  I prefer the color of the T8s but they're not as bright.

 

My shop lighting is a mess...no rhyme or reason for their placement, a mix of T8 and T5...a lot of lights but still not enough.  They get dirty and I don't clean them.

 

Lighting is a science and I never dug into it.  All I know is I still need more...even though my neighbor says it's like looking at the sun when I have my garage door open at night.

==>^^^

Suppose it depends on how long ago you installed the lighting… I had T-12 for years, and then changed-over to T-8s maybe six/seven years ago. I’m not sure I’ve saved a dime, but I do think it’s an improvement… Better ballasts and the quality of the daylight tubes seem better… Don’t really know if that’s true, but it's what I tell myself… :)    My next shop will be T5s…

 

Anyway, I changed-over to T8s because I hated the T12’s mechanical ballasts and (crazy as it sounds) it was about the same cost to replace the entire fixture as re-ballasting the existing T12 setup… Of course, I needed a complete re-tube and that was not exactly cheap (three cases of 4’ T32 Daylight tubes – about 100 tubes)… But I really do think the quality of light is better… :)

Plus they don't sound like ten zillion cicadas and they come on when it's cold.  T12s are stone age.

==>they don't sound like ten zillion cicadas and they come on when it's cold

Yea. I did the shop, garage, outbuildings, etc.. I just couldn't stand the T12 ballasts anymore... Now, I'm totally T8...

Plus they don't sound like ten zillion cicadas and they come on when it's cold.  T12s are stone age.

 

Yep, I need to replace all of mine for this very reason. When it's cold, my garage looks and sounds like the set of horror movie with all the flickering and buzzing lights. I half expect some crazed dude in a bloody lab coat to step out of the corner wielding a rusty scalpel.

Am I the only one using T-12s in my shop? 18x23 with 10 banks of 2 for a total of 20 bulbs.

 

Nope, I have them too.... mostly because that's what I've always had. When I get around to re-doing my lighting, I'm considering going T8.

My t-12s don't make any noise, I run daylight bulbs. Been installed for a year. How long they stay quiet and last, we'll see. But for now it's great.

I always thought it was the ballasts that made the noise.  Honestly the noise wouldn't bother me much since there's always music on...IF they put out enough light...but for me they just don't.  I feel poorly lit with almost a dozen T8 and T5 ballasts.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.