Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Memorial Box for Friend's Golden Retriever

Featured Replies

Looks awesome Tom.  A worthy home for what I'm sure was a great pooch.

 

Where did you get the maker's mark?

  • Author

Looks awesome Tom. A worthy home for what I'm sure was a great pooch.

Where did you get the maker's mark?

Bought it from rockler. They send you a coupon code and a site to enter it to have your brand made.

Nicely done!

 

For the complex glue up you mentioned, I always clamp a carpenter's square to the base, make sure it's perfectly aligned to the pencil marks. That makes alignment a non-issue during glue up.

  • Author

Nicely done!

 

For the complex glue up you mentioned, I always clamp a carpenter's square to the base, make sure it's perfectly aligned to the pencil marks. That makes alignment a non-issue during glue up.

 

The problem with that is the chamfer on the base, and the piece I'm gluing on is only 1/4" thick so the square was getting in the way

The problem with that is the chamfer on the base, and the piece I'm gluing on is only 1/4" thick so the square was getting in the way

oh ok. Looks bigger in the pics [emoji41]

Be honest, did you clean the jointer for the pic or do you have someone come in every night to clean your shop?

 

Tom, Did you get the electrically heat iron?

  • Author

Be honest, did you clean the jointer for the pic or do you have someone come in every night to clean your shop?

 

Tom, Did you get the electrically heat iron?

 

I keep my tops as clean as possible. My jointer is the dirtiest cast in the shop. 

 

I have the electrically heated iron.

  • Author

Base with 1/4" plate for centering box. 

 

IMAG3369.jpg

 

 

Debating if I'm going to put chamfered feet on the bottom, or just clear rubber feet.

 

Screen_Shot_2015_05_21_at_12_56_13_AM.pn

  • Author

Drilled some bird's eye maple with countersinks and glued it to the sides to give the top some more glueing surface (even though it's end grain) and some screws to hold the top on. Too much gluing and such, it's ok to use screws from time to time. 

 

IMAG3374.jpg

  • Author

So tonight was loads of fun. I kept trying to get the top of the box walls completely flat so the top would sit nice and flush. Block plane, smoother, disc/belt sander combo. seems I just made it worse and worse. So I finally gave in and did the tape the sandpaper to the table saw trick. Grueling, torturous, miserable sanding. I figured I'd keep track with my Polar Loop fitness band which I didn't put on all day. It measures motion, and to see if it was accurate, I counted for 100 strokes and it counted 100 strokes. I can't believe how low on full size sheets of sandpaper I am. I've got plenty of 220, 320, 400, 600. I managed to find 1 piece of 80 grit gator red resin paper, which surprisingly lasts a long time. 

 

6377 strokes in about an hour. Makes you a sweaty mess. Tomorrow morning I'll pick up some more sandpaper so I can finish it completely. 

 

Here's some of this daunting task.

 

Tom, I've never tried it, but are you limited by size as to what you can run thru the drum sander, kind of like you are with the planer?

  • Author

Tom, I've never tried it, but are you limited by size as to what you can run thru the drum sander, kind of like you are with the planer?

 

Correct, the case is almost 5" thick and my drum sander can only fit 4".

Sorry, I asked the question before watching the video. I thought you were trying to flatten the lid/top.

Tom I have corrected this issue by taking very light passes on the planer, sending it through diagonally and beveling all the edges before each pass.  It's risky on an almost finished piece of course, but I got to the same point you did where I was just making it worse and worse and just figured screw it I need to get this done.  It worked very well.

  • Author

Ok, break from the Roubo for some odds and ends of finishing the box before putting finish on.

You would think putting the bottom block on after attaching screws would be a better idea. Was interesting doing that with an angle screw driver and an off set head.

78e31d0a4d47d661e24ab0fc01dce122.jpg

I need 1 3/4" screws to attach the base to the box. Before I can put the finish on.

c7de2d070b22ffbcb36e5c3ccfa0ce3a.jpg

  • Author

Drilled for the attachment screws

c5c074f0943fca6db3d6e1a6d32f0ea6.jpg

 

Pressing in t nuts with a C clamp and a block
dfdfd4c7cf4f5611427432332f15ba0b.jpg

 

 

 

 

Danish oil flooded, awaiting wipe off.

b829b2caecf7f66e4a9a975405886e22.jpg

That's going to be one fine, final resting place!

I like that sapele as well. I'm going to get me some tomorrow.

Nice job, Tom. That turned out really well. [emoji4]

Sent from my iPhone using Tapatalk

It's obvious a lot of time, effort and craftsmanship when into the box. Very well done !

A urn I turned for my Aunts Boston Terrier was placed in her casket when she passed a couple of years ago. I thought that was a very nice touch. Our 4 legged friends really do add a lot to our lives.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.