Recommended Posts

Posted

==>Here is the link to the jig Marc built.

Thanks for finding it... Took a quick look -- it'll get the job done, but not the one I was thinking of -- it was a bit more elegant... If I get the chance, I'll do some poking around --- For some reason I'm thinking William Ng... But I seem to remember Marc had gen2 version -- maybe behind the paywall... Anyway, I'll take a quick look...

Posted

I have cut plenty of 3/4" dados with a Porter-Cable 690, so your router will work fine. There are a number of videos on making exact fit router guides for dados, so, it just needs a little searching. By the way, if you are cutting dados in 3/4" ply, 3/8 is fairly deep. 1/4" deep will give significant holding capability and won't unduly weaken the support piece. In the book shelves I have built, 1/4" dados support heavy loads - the limiting factor is the strength of the shelf, not the depth of the dado.

 

Thank you.  I wondered about the depth.  These are not to hold a load, the dados will be the support for the box sides - still 1/4" is probably very appropriate.

 

I agree on 1/4" deep dados being plenty. I got undersized plywood bits at Rockler, they work well, just keep them clean. As you see resin build up on bits the time spent cleaning is well worth it.

If your router will accept ring bushings you can build a jig that makes routing dados much easier. My version is shown in my Mahogany Library stair Project Journal.

 

I don't know if it will or not, but it sounds like a great thing to check today.  I do have the undersize bits on the shopping list.

 

 

www.thewoodwhisperer.com/videos/exact-width-dado-jig/

Here is the link to the jig Marc built. I prefer using the router with dados.

 

Thank you!  I have more than a few conference calls today where that will be good entertainment for me. :)

 

c6d38601989e58c9fd816c8aa0c3f7df.jpg

 

Now that's just hard core.  I appreciate hand carpentry but I don;t see me doing much of it.

Posted

Now that's just hard core.  I appreciate hand carpentry but I don;t see me doing much of it.

 

Never say never.. I always use mine after using my dado stack

Posted

Now that's just hard core.  I appreciate hand carpentry but I don;t see me doing much of it.

 

 

Never say never.. I always use mine after using my dado stack

 

I agree with TIODS...never say never.

 

I am going to buy a Veritas router plane and Lee Valley has free shipping.

Posted

I mean I will not do many (if any) hand woodworking projects. The whole axe to planer thing. I appreciate it of course, it's just not for me. Now cleaning up after machines, that's what ya gotta do sometimes.

Sent from my iPhone using Tapatalk

Posted

I mean I will not do many (if any) hand woodworking projects. The whole axe to planer thing. I appreciate it of course, it's just not for me. Now cleaning up after machines, that's what ya gotta do sometimes.

Sent from my iPhone using Tapatalk

 

The router plane isn't being used to cut them in this case though, it is for cleaning them up and making sure the depth is consistent and so on.  It isn't about dimensioning lumber and the like, but cleaning up and fine tuning fit.  I don't think it would have ever been the tool to cut a dado, but clean it up after using other tools such as stair saws and chisels to remove the bulk of the material.

 

So as a clean up tool it is useful even when using power tools.

  • Like 1
Posted

Gotcha.  I've never even seen one, but I have used blocks of wood and sandpaper in an (ineffective) attempt to clean up a rabbet or dado.  That makes sense.

Look into Marc's hybrid woodworking.  It isn't about the joy of hand tools but about finding the best tool for the job, sometimes that is power and sometimes that is a hand tool.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 41 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined