Brendon_t Posted January 3, 2016 Report Posted January 3, 2016 Recently while jointing I've had a bit more vibration than I think is normal, I should have done the bearings when I first got the jointer but ooh well. Being that it is an 80's clone, is the best bet to pull the bearings, mic them and search or is there a universal size? Any recommendations for sourcing? Quote
Cliff Posted January 4, 2016 Report Posted January 4, 2016 I pulled the cutterhead off and looked at the numbers. It was 6004RS and 6005RS. So I put them in the amazon search and picked the ones sold by VXB because I saw that brand mentioned on here multiple times as a great source. The bearings are made in China but they specify that the bearings are made to their specifications. Cost me about $15 and took two business days. I found myself wishing I had bought a bearing puller off of amazon too. The ones they sold here in town were all just a little wrong. Like the part that goes behind the bearing was too big, and one where it would fit - the steel was flimsy and bent, plus the rod that you twist to pull them off was too short. Quote
Coop Posted January 4, 2016 Report Posted January 4, 2016 I bet Grainger would have them. Me, I'd just turn the music up higher and you'll have "Good Vibrations". Quote
Eric. Posted January 4, 2016 Report Posted January 4, 2016 You can "rent" bearing pullers from Auto Zone. You basically pay for the cost of the puller, and when you return it they give you a full refund. Or you can call it "borrowing" for the untrustworthy. Either way you don't have to buy one. Quote
Brendon_t Posted January 4, 2016 Author Report Posted January 4, 2016 I cannot for the life of me figure out why the would have been making noise. Possibly because the bearing suffered a catastrophic failure. I'm good in the bearing puller dept. That's a mandatory tool in a mechanics box. Unfortunately I'm going to have to dig out my race puller as well as the bearing puller since they are set so close to the housing. Quote
Coop Posted January 4, 2016 Report Posted January 4, 2016 bearing grease or WD-40 and you're good for another 100,000 Quote
Brendon_t Posted January 4, 2016 Author Report Posted January 4, 2016 1 minute ago, K Cooper said: bearing grease or WD-40 and you're good for another 100,000 If I put wd40 on those, I'm afraid the bearings would fall out. Quote
Coop Posted January 4, 2016 Report Posted January 4, 2016 Then you would have a sleeve and not a bearing, not good Quote
minorhero Posted January 4, 2016 Report Posted January 4, 2016 OH golly whatever you do don't put something like WD-40 on them. That will destroy whatever grease is left in there and make them fail completely. When bearings fail badly they do so by wearing away the shaft they are attached to requiring a complete part replacement instead of simple bearing replacement. I buy my bearings off of ebay. Regardless of what shielding your bearings have now you will want ones with rubber shields on both sides. In the bearing world that means "2RS" So if your bearings have numbers on them like 6203-ZZ then you have a 6203 sized bearing with ZZ meaning you have double metal shields. What you would want then is 6203-2RS. A search on ebay will show you a lot of options. You do not need to spend a lot on this. I try to get bearings that are ABEC3 bearings as they are built to higher tolerances. Either way you should be under 5 dollar shipped for each bearing. 2 Quote
Coop Posted January 4, 2016 Report Posted January 4, 2016 I was just kidding about the WD-40, but You provided some great info. Thanks! Quote
Brendon_t Posted January 4, 2016 Author Report Posted January 4, 2016 33 minutes ago, minorhero said: OH golly whatever you do don't put something like WD-40 on them. That will destroy whatever grease is left in there and make them fail completely. When bearings fail badly they do so by wearing away the shaft they are attached to requiring a complete part replacement instead of simple bearing replacement. I buy my bearings off of ebay. Regardless of what shielding your bearings have now you will want ones with rubber shields on both sides. In the bearing world that means "2RS" So if your bearings have numbers on them like 6203-ZZ then you have a 6203 sized bearing with ZZ meaning you have double metal shields. What you would want then is 6203-2RS. A search on ebay will show you a lot of options. You do not need to spend a lot on this. I try to get bearings that are ABEC3 bearings as they are built to higher tolerances. Either way you should be under 5 dollar shipped for each bearing. That are on there are 6203z and 6204z. Are you saying those are inadequate? Quote
minorhero Posted January 4, 2016 Report Posted January 4, 2016 That likely means they have a single metal shield on one side and the other side is open. And yes, those are not as good as 2RS bearings. Rubber shields are better at keeping out dust then metal shields and most bearings on woodworking machines die from dust getting into them and gunking up the grease. I have done a lot of woodworking machine restorations and it is common wisdom on websites like owwm.org (old wood working machines) to replace with 2RS bearings every single time you replace a bearing. BTW if your motor dates from the same time as your machine you may want to replace those bearings as well. I tend to replace bearings on any machine that has been used for 20+ years. Some folks say 10 years but the only time I find 10 year old bearings in need of replacement is when that machine is been really used hard. Quote
Trip Posted January 4, 2016 Report Posted January 4, 2016 ==>replace with 2RS bearings every single time you replace a bearing +1 So they cost a little more... What's you time worth? Quote
Cliff Posted January 4, 2016 Report Posted January 4, 2016 Wish I had read that about 2RS before I did my bearings. I had no idea that is what it meant. I assumed that old bears said "RS" and that's what I had to replace with. Quote
Trip Posted January 4, 2016 Report Posted January 4, 2016 ==>^^^ I looked for an 'Intro to Bearings', but can't find anything that doesn't get quickly into the weeds... There are some guys on WTO who deal in bearings, maybe they have something... Quote
Brendon_t Posted January 9, 2016 Author Report Posted January 9, 2016 Not the bearings in the mail 2RS type. It is now abundantly clear to me that the bearings on this thing were smoked well before they exploded. Reassembly took all of 20 minutes including re shimming the fence. First run and it's soo darn quiet. Quote
CraigW Posted January 11, 2016 Report Posted January 11, 2016 On 1/4/2016 at 4:52 AM, hhh said: ==>^^^ I looked for an 'Intro to Bearings', but can't find anything that doesn't get quickly into the weeds... There are some guys on WTO who deal in bearings, maybe they have something... minorhero has got it bang on as far as the sealing arrangement goes for woodworking gear. I will try to expand on his info a little (without getting into cray amounts of detail): I sell bearings for a living, and almost every woodwork machine I have been asked to supply bearings for came with steel shields (commonly called ZZ or 2Z) from the factory. These have 2 things going for them: they are cheap to buy; and they typically tolerate higher speeds. I prefer to replace these with 2RS (rubber sealed) bearings as stated by minorhero, they are far more effective at keeping dust from entering the bearing. The major difference between the two types is that the 2RS bearings have a rubber sealing lip that contacts the inner ring of the bearing. This is great at keeping crap (dust/water etc) out of your bearing, but generates friction and therefore heat. Too much heat and your grease starts to cook and the rubber seal breaks down, rendering them both useless. ZZ bearings use a steel shield that doesn't contact the inner ring, there is a tiny gap between the two that stops the bulk of contaminants reaching those nice shiny balls. This results in far less friction and heat, but fine dust will find its way in and eventually turn your grease into muck. A lot of reputable bearing companies are now producing a low friction rubber seal bearing, trying to give you the best of both worlds. I have attached a chart from NSK outlining the features of all 3 types (Note they call their 2RS "DDU") It depends greatly on what machine these are going into, a table saw for example should always get 2RS bearings as it is relatively low speed and low use, but you may be better off with 2Z if the machine is very high speed (20,000rpm plus) and runs for extended periods as the heat will wreck the bearing faster than dust ingress. If in doubt, check with the manufacturer if you can for their recommendation. Hope this helps! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.