Derek Posted January 27, 2016 Report Posted January 27, 2016 I have an older Craftsman 6 1/8" jointer Model 103.20260. I like to replace it altogether but due to the lack of space and money it's not really an option at the moment. Besides the usual inadequacies with this jointer, the motor for is sketchy at best. It's a Craftsman 113.12050 1/2hp motor. It's really underpowered, it bogs down on me while trying to face a 3" wide piece of walnut. The motor also heats up very quickly under no load. I could re-wire for 220v, reduce the depth of the cut, and slow the feed rate which would probably help with the lack of power. The temperature issue is most bothersome. The motor uses some sort of felt bearings. I am thinking about replacing it with a 2hp Dayton. They have the same rpm 3450 ( I think that's normal?). So as long as I use the same pulley confriguration would I have any issues? Any thing I might be overlooking by doing this? Here's a pic of the Dayton. Quote
Tpt life Posted January 27, 2016 Report Posted January 27, 2016 Full disclosure...engineering is a hobby interest but is not where I took in my training. RPM and pulley size are all you need. That said, if you up-power you need to make sure that all of the drive system components can deal with the higher load. You may chase the whole way around replacing bearings. 1 Quote
Derek Posted January 27, 2016 Author Report Posted January 27, 2016 That's would definitely something to look into. I know I changed out the bearings for the cutter head when I bought the jointer. Having the jointer disintegrate is a scary thought. Quote
Andy Wright Posted January 27, 2016 Report Posted January 27, 2016 Have you opened up the motor case on your existing motor? Fixing the overheating may be as simple as cleaning the old sawdust, etc in the motor. Then again it could just be a crappy motor... Quote
Derek Posted January 27, 2016 Author Report Posted January 27, 2016 1 hour ago, Andy Wright said: Have you opened up the motor case on your existing motor? Fixing the overheating may be as simple as cleaning the old sawdust, etc in the motor. Then again it could just be a crappy motor... I haven't opened it recently, it been in storage for the last two years. I did some maintenance before running it. But I remember it always ran hot. It's old, probably from the sixties. I checked the bearings I replaced a few years back, they're 99602-H. Seems like they're the equivalent of the 6302rs which are the bearings in my 3hp TS. I think they would hold up to Dayton. Quote
wareaglewoodworker Posted January 27, 2016 Report Posted January 27, 2016 One other thing you need to consider is the direction the shaft spins on the motor. Some motors are reversible, others are not. If the replacement spins the wrong way you may not be able to mount it. That motor is rated for continuous use so try to replace it with a motor with the same rating. I faced the same decision with my dad's old craftsman table saw this past year. I ended up opting to go with a replacement motor from Grizzly that matched the same specs as the original after talking to some contractor friends who informed me that no one around here worked on electric motors anymore. Quote
Brendon_t Posted January 27, 2016 Report Posted January 27, 2016 I know you said it's not in the budget, but if you're planning to drop $250 on a new Grizzly motor, proabably needs belts, and the swap and setup time, your actually well on your way. In my area, an older pm 6" jointer or delta 6" with some miles on it can be had for 250-350 with some patience. I waited and bought a 1970's 8" delta clone for less than the motor then $26 in new bearings. You have already said the jointer has other inadequacies, why throw money at it that could go toward something that fits the bill? If it's absolutely not possible, eBay can be your friend for motors. Of course getting the same rpm and direction is great but you can also use other speed motors if pullies to get it up to 5k rpm are available. Whatever you do, I would be doing the easiest thing first. Remove the motor, bow it out well, ensure it is wired correctly and under proper tension. Free is the cheapest fix. Quote
Larry Moore Posted January 27, 2016 Report Posted January 27, 2016 You also need get the same frame number, otherwise it may be longer shorter or different mount. Quote
Derek Posted January 27, 2016 Author Report Posted January 27, 2016 I already own the Dayton motor. Got it from a rusted out compressor ( I think they forgot to drain the tank ...ever). The original stand when I bought the the machine was shop made which I pitched when the jointer went into storage. Ive made a new stand so mounting the motor isn't a issue. Besides a couple of beefier pulleys and a link belt I haven't spent any money on it since getting it, along with the rest of my things, to Florida. Quote
atlinwi202 Posted January 30, 2016 Report Posted January 30, 2016 The Dayton you ave will work fine and it is reversable. I wouldn't worry too much about the extra HP as you won't really be using it so it won't tax the drive or bearings. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.