Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

I can tune a guitar and now I can tune a plane

Featured Replies

With ack to Joe ...

This week I watched the videos of Cosman and Sellers on plane sharpening. Cosman certainly was more practical, reducing the steps involved and getting to the end product quicker. But Sellers emphasis on precision I also found insightful. So I gleaned from both. Now my Sargent's cuts an even, thin slice. Almost pretty.

Approach: clean everything first, 2 stones, shoulder action, no microbevel. I removed the final burr by pulling back once, turning over and pulling against the bevel, and the once again on the flat side. It's not sharp enough to cut hair but it is sharp enough to cut skin. And, obviously, wood.

655d0937604da0e436df8e8e3560b823.jpg

Sent from my MotoE2(4G-LTE) using Tapatalk

  • Author

Also got the Craftsman cutting nicely.

dfab9dd20a76c2ed5699f9a72dd8ad0a.jpg

Sent from my MotoE2(4G-LTE) using Tapatalk

The old Stanley #3 is going to take a bit more work for a precise cut as the edge is questionable. But for now, for winter practice, it will do. f18cb53ba894a460ba56c2939c3e8c07.jpg

I think I'll call it "Spring Training"

Sent from my MotoE2(4G-LTE) using Tapatalk

A couple of those curls, look so thin that they only have one side!    Good work!

  • Author

Thanks guys.   Cosman's principle of first backing off the blade and then bringing it into the wood made perfect sense. 

Unfortunately the old Stanley #3 has a lot of play in the knob-lever connection.  It's a pain to get set.  The Craftsman is nice and tight but the knob is plastic.  Will probably last long enough for my use but I can't imagine that being used in any production situation.  The Sargent was easy to work with all the way around.  It's a nicely-constructed plane.

A local collector told me that Sargent planes are generally ignored.  That makes them a bit cheaper to purchase, which I found when I got this one.

**

I'd be curious to hear the opinions of others regarding the various approaches to sharpening and if there are other approaches to be gleaned from.)

I sharpen to 8000 grit, secondary bevel, back side microbevel (the ruler trick), sharpening jig, diamond stones, until I can shave my arm with the blade.

 

  • Author
11 hours ago, Immortan D said:

I sharpen to 8000 grit, secondary bevel, back side microbevel (the ruler trick), sharpening jig, diamond stones, until I can shave my arm with the blade.

 

I guess that will come over time with more practice.  At least I've got it doing a "very good" job.  Getting these fine shavings is definitely going in the right direction.  But I won't rush it.  Practice, practice, practice.

Something I did notice was the difference in the metal quality between the three.  The old Stanley as much harder and less flexible than the Sargent and Craftsman.  It was more difficult to sharpen.  I ended up using a very coarse stone to deal with some edge nicks. Even then it was a slower sharpen and still it needs more time. 

**

On Saturday we went antiquing (just walking, not buying) and a local shop had an old Reliable brand, in pretty good shape. for a little < $50.  #7-sized.  I passed on it, but maybe I'll go back another day. 

17 minutes ago, collinb said:

Something I did notice was the difference in the metal quality between the three.  The old Stanley as much harder and less flexible than the Sargent and Craftsman.  It was more difficult to sharpen.  I ended up using a very coarse stone to deal with some edge nicks. Even then it was a slower sharpen and still it needs more time. 

Exactly. And for the hard metals, the secondary bevel will help you maintain the edge with less effort, because you only have to hone that bevel and not the primary one.

  • Author
7 minutes ago, Immortan D said:

Exactly. And for the hard metals, the secondary bevel will help you maintain the edge with less effort, because you only have to hone that bevel and not the primary one.

Gotcha. It's not like a router or shaper piece where a second bevel would ruin the output.  More like a kitchen knife where beveling both side adds to the sharpness and usefulness.

11 minutes ago, collinb said:

Gotcha. It's not like a router or shaper piece where a second bevel would ruin the output.  More like a kitchen knife where beveling both side adds to the sharpness and usefulness.

You got it right. The secondary bevel is only there to speed up the honing process, it is the only reason of its existence. Basically you only use your coarse stone for the primary bevel, and the higher grit stones only for the secondary.

Now the higher you hone your end bevel (secondary or primary if you don't have a secondary bevel), the smoother your wood will end up being. With 300 grit your plane will cut, but if you want a smooth cut, you need 1000 and up. Some folks suggest going up to 16000 grit, others use leather with polishing compound as the final step, a third group would use diamond paste on  MDF, etc.... lots of different schools of sharpening.

  • Author
11 minutes ago, Immortan D said:

You got it right. The secondary bevel is only there to speed up the honing process, it is the only reason of its existence. Basically you only use your coarse stone for the primary bevel, and the higher grit stones only for the secondary.

Now the higher you hone your end bevel (secondary or primary if you don't have a secondary bevel), the smoother your wood will end up being. With 300 grit your plane will cut, but if you want a smooth cut, you need 1000 and up. Some folks suggest going up to 16000 grit, others use leather with polishing compound as the final step, a third group would use diamond paste on  MDF, etc.... lots of different schools of sharpening.

My final is 1200, but I can see where the cut would be better if I sent to 4K.

I have have the jig for doing the bevel but though I'd give Cosman's shoulder action approach a try.  It worked OK but perhaps not as well as it needed to, at least for me.  Still, it was a successful first serious attempt.  I'm happy and the wood is smiling back.  Next time, better.

I'd try going higher than 4k if you have the stones for it. Not only does it give you a sharper tool that cuts easier but i feel like the edge lasts longer the better i sharpen it.

  • Author
48 minutes ago, Llama said:

Can you Tuna Sammich? 

Something's fishy here.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.