Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Polyurethane over BLO

Featured Replies

Im finishing up a countertop that Ive made out of Maple.  Id like to get a little more color out of it, but it not to be too dark. BLO is the closest ive gotten to the color I want over some of the stains that I have tried.  I also want a protective finish over it.  Can I poly over the BLO once I apply?  It will be an oil based poly so they are compatible-my issue is with the color that BLO has made, will that be "locked in" by the poly or will it fade over time?  any hlep and or suggestions would be greatly appreciated.  Ive seen back and forth remarks regarding this.  I have a few days to allow the BLO to "cure" or dry, but I dont have months.  Any help?  Thanks

I've never used pure BLO, but I use Deft's Danish oil often.  Whenever I want to wipe on oil-based poly over it, I usually wait a few weeks - until I can't smell the Danish oil anymore.  That's what I read somewhere, and I forget the reason why.  If I had to guess, it might be the extra mineral spirits in the wiping poly would redissolve the danish oil if I didn't wait until it fully cured.  I'll let someone else chime in.

Edited by nerdbot
Unsurprisingly, I was wrong about BLO never curing.

19 minutes ago, dscealf said:

  I have a few days to allow the BLO to "cure" or dry, but I dont have months.  Any help?  Thanks

Blo can take significantly longer than a few days to "fully cure" by the nose test

The last end table I used blo in was still off gassing slightly three weeks later.

Have you tried any of the Tried and true polymerized oils?  In the few times I've used it on hard maple,  I believe it was a far superior finish to blowith much less nasty

Isn't there a nice mix of BLO mineral spirits and oil poly that dries faster but looks similar? I finished a small box that i made for my dad with that combination (i think) a couple years ago.

Still took a long time to dry before i top coated with pure poly.

  • Author

Brendon, 

Any of the "tried and true" polymeralized oils that you recommend?  Im not sure Im familiar with them.  Ive heard of people mixing BLO/Poly with a 50/50 mix and applying it. I wonder how they got around to the BLO drying or curing beforehand. Im ok with using another finish other than BLO, just not sure whats out there versus the color I want to achieve really.

The only one I've tried is the tried and true  original wood finish. Can't speak to the others in the line. 

  • Author

So is the suggestion to use just the tried and true and no polyurethane over

or that the polymeralized BLO dries quicker and thats what I should use if im going to poly?

I dont see or know how much different the Lowes version of BLO is different than tried and true-if anybody knows, speak now.

The lowes version of BLO is processed so that it dries quicker than Raw Linseed Oil- I would think that tried and true is not much different unless somebody knows otherwise

Thanks for all the help

BLO DOES fully cure, it just takes weeks.

I see no advantage of putting BLO on top of stain.  What's the point?

Stain (if you must), let the stain dry completely, then move on to poly.  The BLO adds nothing in this case.

T&T is great but I don't think I'd use it on a countertop.  It's a PITA to apply on large areas, and it won't offer nearly as much protection as poly.  A countertop will need mucho protection.

  • Author

Stain was never part of the equation.  I cannot find a stain that I like, but I like that antique patina that BLO adds. So I was going to BLO, then poly over that for protection.  Is there something else that I can use to get the same effect as BLO that I can poly after?

Oh, sorry, I misread.

Yeah, BLO on raw maple will give you banana colored counters.  Trust me.

If you want to maintain the stark white of maple, look into water-based finishes.

If you want a little amber color to your maple, go with Arm-R-Seal.

If you want very little protection and like to torture yourself, use T&T.

If you like the color of bananas, use BLO.

Blonde shellac (zinsser seal coat) gives maple a little color without turning into a banana and you can put anything on top of it.   

General Finishes endurovar is another good option.  It will give you some color but not as much as oil.

Eric is correct.  BLO might look good on a small sample.   But it will be very yellow and very blotchy (uneven coloring)!on a large maple countertop.   Shellac and EnduroVar won't blotch on maple like BLO does.  

55 minutes ago, Eric. said:

 

If you want very little protection and like to torture yourself, use T&T.

 

I didn't remember this was on a countertop when I said that. 

Agreed that t&t doen not have enough built in protection for a countertop.

Agreed, would not be my first choice for a counter top either..

How about tung oil under the poly? Isn't is less yellow than BLO?

Yes but it's still a gratuitous step.  What benefit would it add?

No idea, the poly itself is going to lend a warm tone.

I guess my question was partly self serving. I need a finish for my as yet incomplete workbench & want something that will warm up the maple, but don't want it to look like it's made of lemon peel. And I don't want to use poly on it.

10 minutes ago, drzaius said:

No idea, the poly itself is going to lend a warm tone.

I guess my question was partly self serving. I need a finish for my as yet incomplete workbench & want something that will warm up the maple, but don't want it to look like it's made of lemon peel. And I don't want to use poly on it.

Danish oil.  Doesn't yellow, doesn't build a thick film.  Just quenches the wood's thirst and offers a touch of protection.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.