Popular Post Jason Hotze Posted May 5, 2016 Popular Post Report Posted May 5, 2016 So I figured I would put my progress of a commissioned trestle table on here. I have been doing commissions on the side for about 6 months and this once one of those projects where my mouth agreed to more than I have done before. But without too much error I am not at the finishing stage which I will update as I start the dye stain today. Original Sketchup overview. Color will not be nearly as picnic table in the end. This is the lumber like before I started. All 8/4 VERY clear and straight grain pine. 10" wide x 12' long Due to the size of many of the pieces I had to glue up almost every component. Only thing I should have thought about was the grain on these. I just kinda slapped them together. Also had a lot of hand plane clean up as my jointer wouldn't fix many of these. Did all the tenons with my RAS and a dado stack and cut the mortise's with a hand drill and chisels. Got the wedge made from Sapele Drilled all the holes for attaching the x-beams. Going to finish the entire thing before I attach them. Plan on using one screw and filling the hole with black epoxy. Wanted to use a 1" dowel but can't find a good way to stain it black and have it cut to the right size. Got everything fitting well and the curves and rounded on the ends. For the top glued up. This thing is massive. 2"thick 8' long and 40" wide. Weighs probably 150-200 lbs. So my finishing is starting tonight in my living room. Going to be two applications of Charles Neil Blotch Control, General Finishes Dye Stain 3:1 Medium Brown to Orange, one coat of De-Waxed Shellac followed by one coat of Dark Walnut stain and General Finished High Performance Poly Satin. Thanks for looking! Sent from my iPhone using Tapatalk 4 Quote
RichardA Posted May 5, 2016 Report Posted May 5, 2016 I built a table quite like that about 25 years ago [my ex now has it] the one thing I did different was I made a wedge on the top of the upright post's that locked the table top in place when you drove the leg wedges in. The idea being it became a knock down table, easy to move as we were renting at the time, and 4 pieces were easier to move than one large piece. I've always liked that trestle design, you're doing it very well! Quote
TerryMcK Posted May 5, 2016 Report Posted May 5, 2016 Very nice work. I made one, a little smaller, many years back that looks very similar to yours out of yellow pine. I broke it down after many years of service as it became surplus to requirements and it is currently behind my lumber rack waiting to be repurposed as something else! Hopefully you get many years out of yours. Quote
Jason Hotze Posted May 5, 2016 Author Report Posted May 5, 2016 Well this was a commission piece Terry but hopefully they like it for many years. Richard the top will have slats that straddle the base assemblies and I plan on using a long decorative dowel to "pin" the top to the legs Sent from my iPhone using Tapatalk Quote
wdwerker Posted May 5, 2016 Report Posted May 5, 2016 Sometimes jumping in to find out you are over your head can be a learning experience. It's easy to deliver more than they paid for or charge less than you should have. Its looking like a nice sturdy table that should last generations . Quote
Jason Hotze Posted May 5, 2016 Author Report Posted May 5, 2016 Thanks bud. I definitely learned a lot on this project. So far it is that I need better chisels. I need to not drop them on a concrete floor directly after sharpening them... I also need to buy a drill press.. Sent from my iPhone using Tapatalk Quote
Chestnut Posted May 5, 2016 Report Posted May 5, 2016 27 minutes ago, Jason Hotze said: Thanks bud. I definitely learned a lot on this project. So far it is that I need better chisels. I need to not drop them on a concrete floor directly after sharpening them... I also need to buy a drill press.. Sent from my iPhone using Tapatalk I've learned that concrete hand tools and gravity don't = a good project. Many curse words used. I made a holder for my chisels and became diligent on putting them back when done it helped. Quote
Jason Hotze Posted May 5, 2016 Author Report Posted May 5, 2016 Yea I totally ruined my 1/4 inch chisel. Which was a cheapo but had a lot of time out in and had a very nice edge. Sent from my iPhone using Tapatalk Quote
Jason Hotze Posted May 8, 2016 Author Report Posted May 8, 2016 Got everything in my living room for finishing. If you saw my post from the finishing section I'm having trouble with the Sealcoat shellac dragging the dye round so the top of the table I'm going to take in the garage and spray the dye and shellac on. Sent from my iPhone using Tapatalk Quote
Popular Post Jason Hotze Posted May 16, 2016 Author Popular Post Report Posted May 16, 2016 So i finally finished this monster.. Color turned out perfect after many trials and I definitely learned a LOT about finishing! Sorry for the link instead of the pictures but I haven't edited them yet and they are too large to put on here. 3 Quote
..Kev Posted May 16, 2016 Report Posted May 16, 2016 Looks awesome! Thing is definitely a beast! Nice work! Quote
Jason Hotze Posted May 16, 2016 Author Report Posted May 16, 2016 Had this one on my phone if the link isn't working. Sent from my iPhone using Tapatalk Looks awesome! Thing is definitely a beast! Nice work! Thanks! 2 Quote
shaneymack Posted May 16, 2016 Report Posted May 16, 2016 Holy macaroni that thing is a beast ! Beautiful table Jason !! Sent from my SM-N910W8 using Tapatalk Quote
wtnhighlander Posted May 16, 2016 Report Posted May 16, 2016 That is one massive table, and it looks great! With a little age, I'd swear it came from the great hall of some midieval castle. You visit Terry's place for ideas?? Quote
Jason Hotze Posted May 16, 2016 Author Report Posted May 16, 2016 Thanks guys! Funny you say that because the customer wanted it to be Viking-esque Sent from my iPhone using Tapatalk Quote
Chestnut Posted May 16, 2016 Report Posted May 16, 2016 Looks really good jason it appears the finish turned out well after deciding to spray. Quote
Jason Hotze Posted May 16, 2016 Author Report Posted May 16, 2016 It did! Although I had to take the top all the way back to bare wood because I ran out of stain midway and mixed up some new stuff real quick and dorked up the mixture. Table was SUPER red. So sanded it all back down and started over. Turned out good though because the edges and chamfer between the boards kept some color and made them look aged. Thanks for your guys help on here! Sent from my iPhone using Tapatalk Quote
wtnhighlander Posted May 17, 2016 Report Posted May 17, 2016 ... the customer wanted it to be Viking-esque Sent from my iPhone using Tapatalk Nailed it. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.