Southwood Posted August 2, 2016 Report Posted August 2, 2016 I just got the boom arm attachment for my CT26 and was wondering about the outrigger. (Guess that is what we should call it.) Anyway, I have mine set up to swing to the left and not the rear. Does anybody really use the thing? Anybody ever had one flip over if they don't use it? Quote
..Kev Posted August 3, 2016 Report Posted August 3, 2016 I typically don't use them. I have had it tip a few times but, I've always caught it before it went all the way over. I will kick them out if I've got it out in the middle of my floor rather than under my work table. Quote
wdwerker Posted August 3, 2016 Report Posted August 3, 2016 I made my own version and did tip the whole thing over once trying to move it over a shop floor with lots of air hoses and cords. No harm to the arm or vac. I am just a little more cautious now. Quote
Eric. Posted August 3, 2016 Report Posted August 3, 2016 Nope, don't use it. It's in the basement in a box. The CT with boom on it is already a monster in a small shop...the outrigger makes it straight up ignorant. I don't find I need it anyway unless I'm really tugging on it by the hose...which I don't. Quote
Southwood Posted August 3, 2016 Author Report Posted August 3, 2016 That's where I am at. It almost doubles the foot print of the thing. I put the side pieces on and folded them forward tucked up close. Guess I will just swing one of those out if I feel I need to. Quote
davestanton Posted August 3, 2016 Report Posted August 3, 2016 I think the boom arm was aimed at the automotive repair industry to stop hoses rubbing against vehicles. I know my green plugit lead is a non-marking lead designed for the automotive industry. So, if I was working on a car and had the vac beside the car I would want the stabilizing arms. 5 minutes ago, Southwood said: That's where I am at. It almost doubles the foot print of the thing. I put the side pieces on and folded them forward tucked up close. Guess I will just swing one of those out if I feel I need to. The problem with the arms against the vac is the front wheels don't like to turn to steer anymore. Quote
TerryMcK Posted August 3, 2016 Report Posted August 3, 2016 I hang my vac hose over one of the many exposed beams I have in the ceiling of my shop. No need for a boom arm. Quote
Eric. Posted August 3, 2016 Report Posted August 3, 2016 I find the boom very handy. I keep my CT near the middle of my shop, and with the boom I can get the end of my hose to every work surface I have without having to drape it over my shoulder or having it rub and catch against the edges of my workpieces. I wish there were a more compact solution, but I've grown accustomed at this point to how much space it takes up. Quote
midtnwoodworker Posted August 3, 2016 Report Posted August 3, 2016 I haven't had mine very long, but it doesn't ever move from where I have it so I didn't even put the outriggers on. It is ridiculous how much room they take up. Quote
Southwood Posted August 3, 2016 Author Report Posted August 3, 2016 10 hours ago, davestanton said: The problem with the arms against the vac is the front wheels don't like to turn to steer anymore. I noticed that as well. If I keep this arrangement, I will cut an inch or so off so that doesn't effect the wheels. Quote
wtnhighlander Posted August 3, 2016 Report Posted August 3, 2016 If your shop is small, would a bungee from the ceiling work as well as the boom arm? Quote
Tom Cancelleri Posted August 4, 2016 Report Posted August 4, 2016 I've tipped my CT48 3 times. Twice by opening the garage door and it catching on the hose holders (I've since rotated them to the side and this isn't an issue anymore. The third time I was trying to reach something and I was pulled the hose a bit too much. I have the legs installed on the side but they are parallel to the body of the CT. I turn them out if I need to, but I never installed the cross braces. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.