bleedinblue Posted December 20, 2016 Report Posted December 20, 2016 Sooner rather than later I need to rectify my biggest "big five" deficiency and build a decent router table. My current table has a Craftsman in it and the router it's self does just fine, however I can not make above the table bit changes. Bit changes require removing the router motor completely. The router has a spindle lock button and a single nut. Is it possible to use this router in a table and do above the table changes? Quote
Just Bob Posted December 20, 2016 Report Posted December 20, 2016 Google muscle chuck, or the much less expensive option of a bit extension. Both will reduce your routers's depth of cut but they will allow for above table changes. ' Quote
bleedinblue Posted December 26, 2016 Author Report Posted December 26, 2016 Not much action. I looked into the Muscle Chuck, the craftsman isn't listed as compatible. I'm a bit concerned that any sort of extension would reveal problems with the router that aren't apparent as is. I'd assume an extension would amplify any slop or run-out, if run-out is a thing with a router. We are talking about a $150 router... Perhaps I should replace the router after all. Quote
gee-dub Posted December 26, 2016 Report Posted December 26, 2016 The Musclechuck, Eliminator and the like are cool but, I don't know that tossing $60 to $120 at a router that could be re-purposed as a hand router is the way I would go. If you are rectifying a deficiency I would fall back and assess what your goal is. Don't get me wrong, I have tools and assemblies that I have cobbled together that still do their job. I also have been known to throw money at a problem until I exceed what a better solution might cost . Some C-man routers are made by the folks who make Bosch routers so finding a fit should be doable if that is the direction you want to go. I have several hand held routers even though I am just a one man shop. Over time, having a trouble free dedicated router table AND a small stable of hand held routers makes my limited shop time more efficient and more enjoyable. 1 Quote
Brendon_t Posted December 26, 2016 Report Posted December 26, 2016 I have a craftsman in my table and have the same issue of no in table changes. Honestly, it annoyed me for about a week but I don't even think about it any more. I can drop the motor out, change the bit and reinstall in under a minute without rushing. It's not a huge time suck or inconvenience. Just part of my work flow. Quote
Isaac Posted December 26, 2016 Report Posted December 26, 2016 On the positive side, if you do get another route, having an extra free one is never a problem. I find have extra routers reduces the hassle of to switch bits, bases and gives the option of dedicated jigs, such as compass one for cutting large diameter circles. 1 Quote
Elroy Skimms Posted December 27, 2016 Report Posted December 27, 2016 I bought this (http://www.sears.com/craftsman-12-amp-2-hp-fixed-plunge-base-router/p-00927683000P?redirectType=SKIP_LEVEL) a few years ago and it worked well. The plunge base has above table micro adjustments. IIRC, I could also do above table bit changes too. But I couldn't find an aluminum plate for it when I wanted to upgrade to an Incra table. I moved the Craftsman over to be a dedicated handheld tool and bought a nice Triton TRA001 router for the table. The Triton also includes above the table micro-adjustment and bit changes, and more power than my Craftsman. The Triton never leaves the table and the Craftsman gets plenty of use freehand. -E Quote
bleedinblue Posted December 27, 2016 Author Report Posted December 27, 2016 On 12/26/2016 at 0:02 PM, Brendon_t said: I have a craftsman in my table and have the same issue of no in table changes. Honestly, it annoyed me for about a week but I don't even think about it any more. I can drop the motor out, change the bit and reinstall in under a minute without rushing. It's not a huge time suck or inconvenience. Just part of my work flow. I have dropped the router for bit changes for a few years now. About five weeks ago, I was changing the bit in my Makita trim router (it has the same button spindle lock) and the wrench slipped, crushing the tip of my finger between the wrench and the body of the router. Not a huge injury, but I'm not convinced my finger wasn't (or isn't) broken. It was just the tip so I didn't bother going to the hospital. That got me thinking about this more. I've busted my knuckles on the Craftsman more than once during bit changes, it's not difficult and it is quick, but things happen. On 12/26/2016 at 1:01 PM, Isaac Gaetz said: On the positive side, if you do get another route, having an extra free one is never a problem. I find have extra routers reduces the hassle of to switch bits, bases and gives the option of dedicated jigs, such as compass one for cutting large diameter circles. No doubt about it. 3 minutes ago, Elroy Skimms said: I bought this (http://www.sears.com/craftsman-12-amp-2-hp-fixed-plunge-base-router/p-00927683000P?redirectType=SKIP_LEVEL) a few years ago and it worked well. The plunge base has above table micro adjustments. IIRC, I could also do above table bit changes too. But I couldn't find an aluminum plate for it when I wanted to upgrade to an Incra table. I moved the Craftsman over to be a dedicated handheld tool and bought a nice Triton TRA001 router for the table. The Triton also includes above the table micro-adjustment and bit changes, and more power than my Craftsman. The Triton never leaves the table and the Craftsman gets plenty of use freehand. -E That looks to be the exact router. It's a decent enough router and I'm glad I bought it no matter what I end up doing with it. It might become a dedicated mortise setup since the small Makita shines at edge treatments. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.