davewyo Posted December 27, 2016 Report Posted December 27, 2016 I just wanted to give the heads up that this 30 tooth Freud glue line rip blade will not give you a square cut for things like splines and such. The cut looks like this: http:// because , as shown in one of the photos on the amazon link, every other tooth has bevels on it and those teeth stand proud of the FTG teeth. Like this: http:// Quote
gee-dub Posted December 27, 2016 Report Posted December 27, 2016 I have a Carbide Processors rip that is designed the same way. I can definitely feel the difference between FTG and FTG/TCG on thicker stock. It does remove the multipurpose of your rip as a FTG but, gives better rip performance for me on my 3HP saw. An FTG rip will give good flat bottom grooves but, crosscuts can be a challenge. I have a 50T ATB with a flat top raker for cutting flat bottoms with or across the grain. Quote
Chet Posted December 27, 2016 Report Posted December 27, 2016 That is my go to rip blade and I guess in a down and dirty would it gives a pretty good glue line rip. But for nice stuff I still run my hand plane over it or take it to the jointer. Quote
davewyo Posted December 27, 2016 Author Report Posted December 27, 2016 9 minutes ago, gee-dub said: I have a Carbide Processors rip that is designed the same way. I can definitely feel the difference between FTG and FTG/TCG on thicker stock. It does remove the multipurpose of your rip as a FTG but, gives better rip performance for me on my 3HP saw. An FTG rip will give good flat bottom grooves but, crosscuts can be a challenge. I have a 50T ATB with a flat top raker for cutting flat bottoms with or across the grain. 7 minutes ago, Chet K said: That is my go to rip blade and I guess in a down and dirty would it gives a pretty good glue line rip. But for nice stuff I still run my hand plane over it or take it to the jointer. Yeah, I have no problem with the quality of the cut. I wasn't looking for a "glue line" cut off the saw despite the name of the blade. I have a couple of ATBs for general purpose use. I was trying to get a dedicated FTG rip blade for using on my tenon jig and for splines in box corners, etc but I messed up and got the thirty tooth blade. Apparently the 24 tooth Freud rip blade has a true FTG. I should have looked closer and not assumed that any rip blade would give flat bottomed cuts. Quote
Popular Post shaneymack Posted December 27, 2016 Popular Post Report Posted December 27, 2016 Apparently the 24 tooth Freud rip blade has a true FTG. It is Sent from my SM-N910W8 using Tapatalk 4 Quote
davewyo Posted December 27, 2016 Author Report Posted December 27, 2016 1 hour ago, shaneymack said: It is Thanks Shane! I have one on order. 1 Quote
knotscott Posted December 29, 2016 Report Posted December 29, 2016 On 12/27/2016 at 9:42 AM, gee-dub said: ...I have a 50T ATB with a flat top raker for cutting flat bottoms with or across the grain. Only a true Flat Top Grind (FTG) will leave a truly flat bottom. An ATB/R combination grind won't leave flat bottoms either, because the ATB teeth stand proud of the flat raker much the same way a chamfered tooth stands proud in a Triple Chip Grind (TCG). The teeth that are proud wouldn't really do anything if they weren't proud of the raker. Most true FTGs are found in bulk rip blades. Some good FTG options are the Freud LU87(TK)/LM72, Infinity 010-024/010-124, CMT 201.024.10/202.024.10, and Amana RB1020 or 610240. Note that the Freud Diablo, Oshlun, and Irwin Marples rippers (among others) are ATB grind. ATB/R: TCG: FTG: 1 Quote
Tom Cancelleri Posted December 30, 2016 Report Posted December 30, 2016 I have the Ridge Carbide TS2000. Every fifth tooth is a flat raker and leaves a flat cut, after the 4 previous ATB teeth. Cut quality is great, there's a lot of carbide on each tooth. http://ridgecarbidetool.com/10-ts2000-super-blade.html 1 Quote
Isaac Posted December 30, 2016 Report Posted December 30, 2016 On 12/27/2016 at 0:41 PM, shaneymack said: It is Sent from my SM-N910W8 using Tapatalk Just bought the thin kerf cut version of this one on Amazon, haven't even tried it yet, but will let you know if I see anything other than FTG. Great price btw, only $38.99 USD right now. 1 Quote
knotscott Posted December 30, 2016 Report Posted December 30, 2016 6 hours ago, Tom Cancelleri said: I have the Ridge Carbide TS2000. Every fifth tooth is a flat raker and leaves a flat cut, after the 4 previous ATB teeth. Cut quality is great, there's a lot of carbide on each tooth. http://ridgecarbidetool.com/10-ts2000-super-blade.html Great blade, but the kerf isn't flat. It'll have minor bat ears on each edge from the ATB teeth. I'll say again....only an FTG blade will leave a truly flat bottom. The TS2000 has an ATB/R grind. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.