prov163 Posted March 4, 2017 Report Posted March 4, 2017 I'm going to bite the bullet and order a new Shelix head for my DJ-20. The best price I have found so far is from Grizzly at $425 plus shipping. I'll buy new bearings while I'm at it. Anyone know of a better place to buy? Also, have any of you made the change on a DJ-20 and if so, any suggestions? I don't foresee any problems, but always good to ask. Quote
Dknapp34 Posted March 5, 2017 Report Posted March 5, 2017 Thinking about upgrading to a helical cutter head on my griz G0490 too, so I'd be interested in what people have to say. Sent from my iPad using Tapatalk Pro Quote
Just Bob Posted March 5, 2017 Report Posted March 5, 2017 A couple of months ago I upgraded my planer to a Byrd head. It's just fantastic. I ordered it directly from Byrd. In an attempt to save my POS Rikon jointer, last Monday I ordered a spiral head directly from them. Their web page listed my model so I thought it was a done deal. That day they contacted me and said that because of low interest in that particular head they would have to setup their tooling to make it. They told me that there would be at least a 4 month delay. I asked them to cancel the order and refund my money. They apologized and immediately refunded the money. While I was disappointed, and I am now looking for a new jointer, I can't say enough about Byrd. Their products are amazing, and customer service is stellar. I will never buy another tool with straight knives, the difference in cut quality is worth every extra dollar. Quote
RichardA Posted March 6, 2017 Report Posted March 6, 2017 On 3/4/2017 at 1:27 PM, prov163 said: I'm going to bite the bullet and order a new Shelix head for my DJ-20. The best price I have found so far is from Grizzly at $425 plus shipping. I'll buy new bearings while I'm at it. Anyone know of a better place to buy? Also, have any of you made the change on a DJ-20 and if so, any suggestions? I don't foresee any problems, but always good to ask. Be sure it's a Shelix... they also sell the non Byrd type. Quote
Coop Posted March 6, 2017 Report Posted March 6, 2017 With all of this hype, and I'm sure it's warranted, about the Shelix head, what happens when, like any other cutting edge, it gets dull? Do you replace the entire head and how long do they last, and I'm sure the longevity is relative to the amount of use, but say, with us hobbyest? Quote
RichardA Posted March 6, 2017 Report Posted March 6, 2017 Just now, K Cooper said: With all of this hype, and I'm sure it's warranted, about the Shelix head, what happens when, like any other cutting edge, it gets dull? Do you replace the entire head and how long do they last, and I'm sure the longevity is relative to the amount of use, but say, with us hobbyest? Uh, you loosen a screw, and turn the cutter 90*. 2 Quote
wtnhighlander Posted March 6, 2017 Report Posted March 6, 2017 Uh, you loosen a screw, and turn the cutter 90*. Of course, you have to it like, 400 times. Still worth it, IMO. And I don't even have one (yet). Quote
Unknown craftsman Posted March 6, 2017 Report Posted March 6, 2017 On March 4, 2017 at 11:27 AM, prov163 said: I'm going to bite the bullet and order a new Shelix head for my DJ-20. The best price I have found so far is from Grizzly at $425 plus shipping. I'll buy new bearings while I'm at it. Anyone know of a better place to buy? Also, have any of you made the change on a DJ-20 and if so, any suggestions? I don't foresee any problems, but always good to ask. Hope you current head is parallel with your tables.Because if it isn't you will have to shim the head or adjust the tables to be parallel. You cannot adjust the inserts like you have been doing with straight knives. Good luck hope it works out. Aj Quote
prov163 Posted March 6, 2017 Author Report Posted March 6, 2017 A few more advantages: quieter. If one or two cutters get nicks, you just change them and get back to work. You don't have to check height, adjust, etc. leaves a smoother finish. I love the one in my planer. 1 Quote
djhb20 Posted March 20, 2017 Report Posted March 20, 2017 It's super easy to do. Mark had a video of installing one in his powermatic and while it'll be somewhat different, the basics of it will be the same. The one I put in my 6" POS jointer involved basically the same process. Very straightforward. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.