Ronn W Posted June 5, 2017 Report Posted June 5, 2017 Help!! I have tried to calibrate the horizontal position gauge on my new unit. Instructions on page 17 of manual where you mark 2 boards at the same time and see if the lines are still in alignment after drilling the 2 mortises and putting the pieces together. I am within 1/4 mm (about 1/2 of a pencil line width. I had to shave the edge of the plastic gauge to get it this close and am now restricted by the screw against the edge of the hole. In your experience, will this 1/4 mm make a difference even on the tight setting when drilling double tenon joints? Appreciate your input. My alternative is to send the unit back to Festoolproducts.com and put my entire project on hold. The guy on the phone says that there are other calibrations that they do in their repair shop that could fix the problem. Festool is sending a new plastice gauge but the guy doubts that that is the problem. Quote
Eric. Posted June 5, 2017 Report Posted June 5, 2017 I'd say you're probably close enough. When I need a little wiggle room I'll just shave the rib off one or both sides of the Domino with a chisel. That gives you plenty of latitude when you're talking half of a pencil line width. Mine came perfectly calibrated and hasn't moved. It's odd that yours wasn't. Quote
bgreenb Posted June 5, 2017 Report Posted June 5, 2017 Mine wasn't even close from the factory. Honestly probably 1/8" off. I got it to within about a half pencil line, same as you Ronn. I have to shave the ribs off on the right setting, which is annoying, but it doesn't affect my work. Quote
BillyJack Posted June 6, 2017 Report Posted June 6, 2017 It will irritate you..I use two units and both irritate me...One is spot on and he other isn't. If you can, I would send back. The Domino isn't perfect ..... Quote
Guest Posted June 6, 2017 Report Posted June 6, 2017 i had no idea this could be calibrated. Mine also came perfectly calibrated and it would never occur to me it could go out of calibration. Quote
bgreenb Posted June 6, 2017 Report Posted June 6, 2017 The clear plate is held down by a single torx screw and with enough vibration I could absolutely see how it comes out of calibration over time. But I was annoyed mine came from the factory that way. Quote
Eric. Posted June 6, 2017 Report Posted June 6, 2017 11 hours ago, BillyJack said: It will irritate you..I use two units and both irritate me...One is spot on and he other isn't. If you can, I would send back. The Domino isn't perfect ..... Do you send your happy meal back, too, if some of the fries are at the bottom of the bag? Quote
Pwk5017 Posted June 6, 2017 Report Posted June 6, 2017 I almost always use the medium setting on 1 of the 2 mortises. I dont think you sacrifice much strength, and you have plenty of room for error when lining things up/machine out of calibration. The tight setting gives you the warm and fuzzy feel of a perfectly fit M&T, but if your project relies on the strength of that extra little bit of surface area ont he sides of a 8mm tenon, then i think its time to reconsider the joint design altogether. Never considered shaving the glue ribs off the sides before, i really like that trick. That is probably 1-1.5mm of play. Quote
Eric. Posted June 6, 2017 Report Posted June 6, 2017 Just now, Pwk5017 said: That is probably 1-1.5mm of play. I wish FT would have designed the Domino with a slop setting for about that much...just a mm or so...that's usually all you need. The two settings they give you are just way too much unless you're using it for wood movement issues - e.g. faux breadboards. And that's why I stick with the main setting and use the rib-shaving trick. Doesn't take long and gives you just enough play without sacrificing too much joint strength. I do agree that most of the strength is in the Domino faces...but it just doesn't sit right with me to have that much slop at the edges. Quote
Guest Posted June 6, 2017 Report Posted June 6, 2017 sometimes I use a chisel to shave away the edges, sometimes I just run it over 80g paper. But I agree, a tighter slop feature would be nice. That being said, the ribbed edges do allow you to pound them into a slightly tight hole. Quote
bgreenb Posted June 6, 2017 Report Posted June 6, 2017 10 minutes ago, Mike. said: sometimes I use a chisel to shave away the edges, sometimes I just run it over 80g paper. But I agree, a tighter slop feature would be nice. That being said, the ribbed edges do allow you to pound them into a slightly tight hole. Ribbed for her pleasure indeed. 1 Quote
Ronn W Posted June 6, 2017 Author Report Posted June 6, 2017 I like the suggestion of shaving the tenon if needed, The had occurred to me as a plan B. Just cut the double mortises for my leg to base table connections using the tight setting....After I take the dogs for a walk we'll see much shaving I have to do. I will post pics and results in my journal. I like the idea of a smaller slop feature. BTW - I took a closer look at the plastic gauge and it looks like the "Zero" line is not prependicular to the machine or to my layout line so I am hpoing that the replacent gauge will solve the problem. I also chekc the marking on the base of the machine. That mark is dead on the nuts. I appreciate all you comments. Quote
BillyJack Posted June 6, 2017 Report Posted June 6, 2017 10 hours ago, Eric. said: Do you send your happy meal back, too, if some of the fries are at the bottom of the bag? If you like sloppy work, go for it.... Quote
Eric. Posted June 6, 2017 Report Posted June 6, 2017 7 minutes ago, BillyJack said: If you like sloppy work, go for it.... It's something you can calibrate. It's not an irreconcilable problem. Quote
Popular Post wtnhighlander Posted June 6, 2017 Popular Post Report Posted June 6, 2017 It's something you can calibrate. It's not an irreconcilable problem. I feel that if my Happy Meal cost $1k and came in a grey & green box, the fries should stay in their carton, thank you very much. 4 Quote
Ronn W Posted June 7, 2017 Author Report Posted June 7, 2017 4 hours ago, wtnhighlander said: I feel that if my Happy Meal cost $1k and came in a grey & green box, the fries should stay in their carton, thank you very much. That's kinda what I was thinking. You just said it better than I ever could. I dry fit the double tenon joints. See my journal = Kym's Table. (Shameless plug) Quote
Eric. Posted June 7, 2017 Report Posted June 7, 2017 12 hours ago, wtnhighlander said: I feel that if my Happy Meal cost $1k and came in a grey & green box, the fries should stay in their carton, thank you very much. Yeah...but a happy meal is like three bucks and it comes in a greasy red and yellow box. My point was - while slightly annoying because it's a new tool - some calibration is usually expected. I guess I got lucky with mine. But it would be like returning a table saw because you had to align the table to the blade. The headaches of tool maintenance and calibration are just part of being a woodworker. Unfortunately. My least favorite part. I'd rather sand than work on tools. But it comes with the territory. Quote
Guest Randy Posted June 7, 2017 Report Posted June 7, 2017 By now, I suspect that you have done whatever you are going to do with this problem, but I didn't see the post till now. My recommendation for anyone who buys a Festool and isn't satisfied with it's accuracy or any other aspect of its use, is to either return it within the 30 days or send it to Festool Service. My Domino was dead on when I bought it a couple of years ago and has never given me any problems. If it had, I would just have sent it to service. It's what I did with my track saw when I felt there was a bevel angle calibration problem. These tools are just too expensive to do anything else. Plus, the Domino is so easy to use and setup that there should be no difficulties in making it work for you and your projects. It should just work as long as your setup on the wood is correct and you reference the correct faces. Quote
Ronn W Posted June 29, 2017 Author Report Posted June 29, 2017 Update. I got the replacement plastic horizontal position gauge from Festool. Now that I want to use it again I installed the new guage. Removed the old one and installed the new one. Bang! Spot one first try. Problem solved!! I should note that I touch file a couple of rough spots in the metal around the opening that the guage fits in, just in case there were any rough spots that could impede the adjustment of the gauge. Don't know if that was part of the problem. Quote
BillyJack Posted June 30, 2017 Report Posted June 30, 2017 Good deal..... I need to take the time and adjust. Making benches for a courthouse in Virginia and there off a bit. Keeping my mallet busy, Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.