collinb Posted August 3, 2017 Report Posted August 3, 2017 I'm rebuilding my back porch. The original was done well and I want to do just as well plus add some improvements. One thing he did was made the 2x4 cross pieces fit nicely with the 4x4 posts. It makes for a nice tight fit and flat joint. I'm wondering about a simple way to make that cut. If I really want to spend the time. Or I could just fill it with caulk and paint over it. Quote
Rapid Roger Posted August 3, 2017 Report Posted August 3, 2017 I would notch the post about 1/4" deep to fit the 2 x 4. A 1/2" or larger router bit in the router with a depth stop and a template with some careful measuring should do the trick. Quote
mat60 Posted August 3, 2017 Report Posted August 3, 2017 How big of a gap? Could you just rip a little off the 2 by 4 cross piece on the table saw. Quote
collinb Posted August 3, 2017 Author Report Posted August 3, 2017 1 hour ago, mat60 said: How big of a gap? Could you just rip a little off the 2 by 4 cross piece on the table saw. My pic shows two pieces separated. Consider the 2x4 cross piece abutted to the 4x4 upright. At this point I can't find an easy way to make that end. I think I'll just trim off the edges of the 2x4s to provide some relief to the structure's appearance. That's probably no more work than just abutting a flat end and filling with caulk to cover the end grain. 1 Quote
wdwerker Posted August 3, 2017 Report Posted August 3, 2017 1/4" dado in the post like Rodger said. 1 Quote
wtnhighlander Posted August 4, 2017 Report Posted August 4, 2017 If the structure is made from PT pine, don't worry about it. Gaps will appear, no matter what you do. 1 Quote
collinb Posted August 4, 2017 Author Report Posted August 4, 2017 56 minutes ago, wtnhighlander said: If the structure is made from PT pine, don't worry about it. Gaps will appear, no matter what you do. A combination of cedar (2x4s) & douglas fir (4x4s), plus trim pieces. To be painted. Quote
Jean [Fr] Posted August 4, 2017 Report Posted August 4, 2017 @collinb I understand your initial question. I don't know much about your porch construction, but I'm afraid this is not the way to go. PU or epoxy glue won't help that much with a poor construction. I agree with @wtnhighlander about pine is going to wear anyways, even under many coats of paint. I believe paint will bring extra moisture to the wood and as the wood will dry, you can experience some cracks into the paint. Through, the thin wooden wings meant to match the rounded corners of the 4x4" will make a weak point. Tight fit and flat joints does not last that much outdoor. I'm very classic in the way I do outdoor construction. I usually use tongue and groove because it allows wood shrinkage. I don't use screws but dowels with drawboring tenons. It's the only way I know to have assemblies that last outdoor. About outdoor stuff, assembly is more important than finishing. Quote
collinb Posted August 4, 2017 Author Report Posted August 4, 2017 1 hour ago, Jean [Fr] said: @collinb I understand your initial question. I don't know much about your porch construction, but I'm afraid this is not the way to go. PU or epoxy glue won't help that much with a poor construction. I agree with @wtnhighlander about pine is going to wear anyways, even under many coats of paint. I believe paint will bring extra moisture to the wood and as the wood will dry, you can experience some cracks into the paint. Through, the thin wooden wings meant to match the rounded corners of the 4x4" will make a weak point. Tight fit and flat joints does not last that much outdoor. I'm very classic in the way I do outdoor construction. I usually use tongue and groove because it allows wood shrinkage. I don't use screws but dowels with drawboring tenons. It's the only way I know to have assemblies that last outdoor. About outdoor stuff, assembly is more important than finishing. Thanks. The screen porch I'm replacing is 30+ years old. As I was tearing more down last night it appears that the builder didn't use that technique for the whole porch. I would suspect that he gave up on it because of the time involved. It was assembled with nails and held to the slab with a mixture of concrete screws and bolts. I'm just going to cut them off flush and replace with new ones. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.