Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

How to prepare curly maple for finishing.

Featured Replies

Hey all, Im working on a project using curly maple. I was ready to finish the inside of a panel, so I sanded it to 150 grit. I blew it off and wiped it with mineral spirits to remove all the dust, and its as if I sanded the curl right out of the wood. I took a scrap and sanded it as well and put a couple finish options i have on to see if the curl will appear again, which it does, but not nearly to the extent it was before. 

How do you prefinish curly maple? And since im here, what finish shows off the curl the best?

  • Popular Post

 

The appearance of curly figure is the result of undulutations in the wood fibers. This means that in a flat-face board, those undulations are cut through, leaving patterns of end grain showing, creating the figure. I've heard that sanding too fine can burnish the end grain fibers and dampen the appearance of the curl, but 150 seems too low to do that.

 

 

If you have a well-honed card scraper, use it to slice cleanly through those end fibers to make them open again.

 

 

I'm not certain that's the problem here. Usually burnishing to that point means going past 320 grit. It would be unusual to get this effect at 150, unless maybe the paper was worn, and you tried to keep using it past the point where it stopped 'cutting'. Did you notice any heat building at the sanding pad?

For curly material I will sand to 220 and even beyond.  A good penetrating finish will absorb irregularly and accent the curl.  This one is done with only shellac thinned to a 1 pound cut and practically flooded on the surface.  This is sanded back and shellac'd more normally with a 2 pound cut.

5767dfc1f2d18_TylerWeddingFrame(2).jpg.4b9958985f213492814f42fa952db6f3.jpg

This one is dyed in various steps to get a similar but, different result.

58b4d4152eaad_LarryFrame(6).jpg.39c6dd23b9c181335f6c7d3798b00b63.jpg

I can't seem to find the thread showing the more involved method.  I will try to dig that up; maybe I never posted it(?).

  • Author

That looks awesome gee-dub. Before work this morning I went out and sanded a test piece to 220, the highest grit i have at the minute, and the curls seem to be more visible. Maybe its about sanding to higher grit, not lower like I had previously thought. And I may need to pick up some shellac.

  • Author

I cant be certain but its pretty hard stuff.

No stain, in fact I want as little color as possible. I may try to find a pint of dewaxed shellac here in town. I guess it pretty blonde.

A lot has to depend on the wood. Sometimes you see the curl in the wood and after staining/dye or just an oil,  it can come out blah!  Curl can disappear just by holding the board on a different angle.  

A good rule of thumb when building with figured woods ~ the outside facing part of the tree (board) gives the best face.

Hard maple sapwood is very white with tight curls. Soft maple sapwood is more of a beige color and the curl isn't as tight as hard maple. Most of the killer figure comes from the hard maple. 

When you have some killer tiger maple...you will know it, a perfect example is that top picture frame posted above. You have to play with the different grits when sanding to achieve what you want to see. It just depends.  

-Ace-

 

  • Author

Thanks Ace. Its tricky wood no doubt. This board I got isnt the curliest, but theres enough there to work with. Im gonna do some testing on scrap and see what works. I went and bought some dewaxed shellac downtown, im lucky enough to have it available in a store downtown here. 

You mention not wanting to color it and I applaud that.  Since I found it I thought I would post the dye method I used.  It is in merlau's thread here.  The clear dewaxed shellac really lets the iridescent quality shine though so, if that's your desired result, the shellac should do ya.

This mahogany and maple frame is Zinsser's Seal Coat only.  Here's the unfinished material . . .

597140f280129_11-14-frame(21).jpg.24c752f0821981a1eed10f6f8e03ce32.jpg

And with the shellac . . .

591c419d8dd26_11-14-frame(26).jpg.3f0145b0fa222b057578a668be857a2b.jpg

 

I would guess that 150 left the wood too coarse for the light ot refelct as it should off the natural grain variations - try 220 or a little finer.

  • Author

Thanks gee-dub ill check that out. Ronn W, I did take a sample to 220 grit and the curl was more visible under finish. The shellac really shines the wood up, not quite as easy as danish oil to apply though.

Woodbutcher do you use hand planes? I have found them very helpful in achieving wood chatoyance, although you do have to take very shallow cuts, with a sharp plane, so you don't induce tearout. This frame was prepped with a #5 standard hand plane and finished with a coat of shellac and sprayed with rattle can lacquer. 

IMG_2119.JPG.f8692596ec8c1c3b45899a05cdfdecdc.JPG

 

  • Author

Thats exactly the look Im going for. 

Im pretty new to hand planes. I have a no 4 smoother that I have used with some success, although the maple is a challenge with it. It doesnt tear out much, but i have a difficult time getting actual shavings. It mostly takes a little wisp and thats it. I have tried to get a finish ready surface with the plane, but im not achieving it. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.