Popular Post Dknapp34 Posted August 23, 2017 Popular Post Report Posted August 23, 2017 Been a busy summer. Not much woodworking, but I've been doing some shop upgrades (soundproofing insulation in the ceiling, new drop ceiling with a better sound rating, reconfigured dust collection ducting). I figured it was a good time to finally build a tool cabinet that I've been wanting to build for a while. Going to use this design from Fine Woodworking. I have some nice crotch figured walnut that I want to use for door panels and my original plan was to do the whole thing in walnut. The walnut at my lumberyard (which is usually great) was crap though. Except for a few ridiculously priced slabs, all of the walnut had tons of knots and sapwood, despite still costing a fortune. So I decided on the fly that I would pick up some butternut for the cabinet instead. I figured being close cousins with walnut, it would make a nice contrast with the crotch walnut panels, without being too much of a contrast. Never worked with butternut before. Kind of sucks, actually. My planer ate it up and left fuzzies all over the boards, despite having very sharp blades and taking shallow passes. It hand planes beautifully though. Got the boards for the main case milled and cut to size, then I surface prepped the insides of the boards to get ready for dovetailing. Few passes with my #5 to get rid of the planer fuzzies and then sanded to 220 with the ROS: I'm hoping I can start dovetailing tomorrow. 7 Quote
Popular Post Dknapp34 Posted August 24, 2017 Author Popular Post Report Posted August 24, 2017 Got a little bit of shop time last night. Did one set of tails & pins for the main case. The half tail is on the back of the case and is intended to hide a rabbet into which the back panel will fit. Tails cut in the background and pins laid out in the vice: I typically chop out the waste with a chisel, but this time I decided to try cutting it out with a fret saw (also gave me a convenient excuse to pick up a Knew Concepts saw, which I've been wanting for a while). Verdict: way better than using only a chisel! It's so much faster, plus less sharpening I have to do on my chisels. Definitely the way I will be doing dovetails from now on. The only downside is I snapped my only blade (forgot to order replacements), so I need to pick some new ones up. Any suggestions on good blades? Here's a pic of the boards, mid-dovetailing, with the pins only partially seating: After some fiddling: A little more work to do, but they're almost there. If you look closely you might see some blood. It's a new technique I'm working on. You might have heard of the pencil smudge trick for determining where more material needs to be removed, this is similar, but far more painful... 8 Quote
wdwerker Posted August 24, 2017 Report Posted August 24, 2017 I've been using scrollsaw blades in a jeweler's saw for years. Lusted after a Knew Concepts saw but haven't had a project that would justify pulling the trigger on one yet. Really wanted a titanium one but I don't think they are available anymore. I found that high tension, a light touch when cutting and maintaining a quicker stroke gets me the best results right up till it grabs and the blade snaps. That's why I keep around 2 dozen of each different blade on hand. Only practice lets you build speed and accuracy. 2 Quote
Dknapp34 Posted August 24, 2017 Author Report Posted August 24, 2017 Good idea about the scrollsaw blades. The Knew Concepts saw is pretty awesome. I have an old crappy home center saw that I have used for things in the past and it's a night and day difference. Easier to control, keeps tension better, and it just looks cool (I'll admit this was one of the reasons I got it, I am building a tool cabinet to display my tools, after all...) Sent from my iPhone using Tapatalk Pro Quote
RichardA Posted August 24, 2017 Report Posted August 24, 2017 And I'm building a cabinet to consolidate my tools. From 5 wall hangers into one decent size floor model. Quote
Dknapp34 Posted August 24, 2017 Author Report Posted August 24, 2017 You journaling it? I'd love to follow along. My previous storage method was to leave my tools wherever the hell I happened to have them last, and then spend 20 mins trying to find it later. Sent from my iPhone using Tapatalk Pro 2 Quote
bushwacked Posted August 24, 2017 Report Posted August 24, 2017 very cool, looking forward to watching this one Quote
pkinneb Posted August 24, 2017 Report Posted August 24, 2017 Coming along nicely! I made a tool chest out of Butternut and agree the power tools do leave a bit of fuzz but the hand tools work the wood beautifully. Re fret saw blades for DT's, I usually use a 12 TPI skip tooth scroll saw blade Quote
Popular Post Dknapp34 Posted August 26, 2017 Author Popular Post Report Posted August 26, 2017 Finished dovetailing the main case, which is 10" deep. The doors will be 3" deep to accommodate more storage: Found a new use for systainers; here's a shot of where the tool cabinet will hang when it's done: Ignore the clutter, missing ceiling tiles and all-around massive mess... This cabinet build is part of a larger shop upgrade, so hopefully, when it's all done, everything will be neat and organized. 3 Quote
RichardA Posted August 26, 2017 Report Posted August 26, 2017 On 8/24/2017 at 0:09 PM, Dknapp34 said: You journaling it? I'd love to follow along. My previous storage method was to leave my tools wherever the hell I happened to have them last, and then spend 20 mins trying to find it later. Sent from my iPhone using Tapatalk Pro Nah, just gonna do a finished product. Quote
Dknapp34 Posted September 2, 2017 Author Report Posted September 2, 2017 Update time: Finished the frames for the 3" deep doors: Also finished the face frames for the doors. Frames are dominoed together. Had a little bit of a resawing issue with the crotch walnut panels I was planning on using. Thought I was going to be able to get 4 panels out of two boards, but it looks like I am only going to be able to get 2. Since I only have 2 of the heavily figured crotch panels, I either need to try and find some similar crotch boards, or use this other piece I have (the one on the left below), which also has some crotch figure at the bottom. The original plan was to have both doors look like the one on the right (bottom panel is darker because it has mineral spirits on it). I'm still trying to figure out if I like the look of the two different doors together. Love to hear others' thoughts... 1 Quote
Eric. Posted September 2, 2017 Report Posted September 2, 2017 Can you resaw the crotch piece into veneers? Can't say I'm a fan of those two boards together. They may as well be two different species. Quote
Dknapp34 Posted September 2, 2017 Author Report Posted September 2, 2017 Think you're probably right about that. Unfortunately, I don't have capacity on my band saw to resaw them. I'll look around online and see if I can find something with a similar grain pattern. Might just have to save those panels for another project and get something different entirely. Worst case scenario, I can buy some veneer and make veneered panels. Quote
Popular Post Dknapp34 Posted September 5, 2017 Author Popular Post Report Posted September 5, 2017 Ordered some interesting looking crotch figured veneer for the panels from VeneerSupplies.com. We'll see how it looks in real life when it arrives. In the meantime, I did some test fitting of my planes on the plane till: 4 Quote
bushwacked Posted September 11, 2017 Report Posted September 11, 2017 coming along!! Cant wait to see more Quote
Popular Post Dknapp34 Posted September 12, 2017 Author Popular Post Report Posted September 12, 2017 Veneer came over the weekend. Wasn't sure what to expect, since I've not worked with veneer before, but it is some pretty beautiful stuff. Very happy with my purchase. The veneer was pretty wonky when it arrived, so I sprayed it down with veneer softener and have been pressing it between melamine, with layers of paper towels and fiberglass window screen material, pressed between some cauls. I put a slight convex curve on the cauls using a hand plane so that when I clamp the ends there is good pressure in the middle: Here's the veneer, mid-flattening (still feels cold to the touch, so it needs a little more drying time): Here's the pattern I am thinking about using for the door panels: Should be dry in another day or so, after which I will glue them to a plywood substrate with a cheaper veneer on the back of the panels to balance it out. 7 Quote
wdwerker Posted September 12, 2017 Report Posted September 12, 2017 That looks wicked ! Fresh paper helps w drying. What kind of glue did you decide on? You might want to do a little test run if you have some spare veneer. Quote
pkinneb Posted September 12, 2017 Report Posted September 12, 2017 That looks sweet! Definitely the right choice. Quote
Eric. Posted September 12, 2017 Report Posted September 12, 2017 Way to go the extra mile. Totally gonna be worth it. Quote
Dknapp34 Posted September 12, 2017 Author Report Posted September 12, 2017 1 hour ago, wdwerker said: That looks wicked ! Fresh paper helps w drying. What kind of glue did you decide on? You might want to do a little test run if you have some spare veneer. Was thinking about using Titebond Cold Press Veneer Glue. Have never used it before, but they carry it at my local woodcraft. My plan was to glue up the back side of one panel first as a test run. Quote
wdwerker Posted September 12, 2017 Report Posted September 12, 2017 Smart move. Going to use the same clamps & cauls ? Quote
Dknapp34 Posted September 12, 2017 Author Report Posted September 12, 2017 9 hours ago, wdwerker said: Smart move. Going to use the same clamps & cauls ? Nope. Planning on using 4 cauls across the top and bottom, and the panel will be sandwiched between two layers of 3/4" mdf on each side. Hopefully that will give me enough evenly-distributed clamping pressure. Quote
wdwerker Posted September 12, 2017 Report Posted September 12, 2017 Should work I think. Don't overtighten the clamps. Even pressure is what you want. If overtightened you can get lumps where the glue is forced out from under the cauls and glue starved stripes under the cauls. Apply the glue as evenly as possible. Quote
Popular Post Dknapp34 Posted September 16, 2017 Author Popular Post Report Posted September 16, 2017 Glued up the panels, here's the set up I used: Here's one of the panels with a coat of ARS: Two of the panels have slight cracks in the veneer that didn't quite glue up perfectly. You wouldn't notice unless you were looking closely, but I have two extra sheets of veneer so I'm just going to glue up two more panels. Might as well do it right. In the meantime, I started cutting the mortises for the hinges. Doing this the old fashioned way with a chisel, because I'm making a hand tool cabinet and it just seemed like the right thing to do. 5 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.