21meyer Posted September 15, 2017 Report Posted September 15, 2017 We need to replace ceiling steel in some livestock facilities. The sheets of steel are 4' x 20'. The way we have done it in the past is to use a coil nailer to secure the old sheet and then remove the pole barn screws so we can put a new sheet directly over top the old sheet. This way the attic insulation does not need to come down because it is in good shape. Hopefully my explanation of our process makes sense. The issue is having an air hose draped over gating and the animals chewing on it. We do not have the option of removing the animals or waiting until the next fill. I see that Paslode and Duo-Fast make a cordless coil nailer but was curious if anyone knew of any other manufacturers or possibly a more efficient way of replacing the steel. Quote
Tpt life Posted September 15, 2017 Report Posted September 15, 2017 Two or three nails will hold a whole sheet if this is a low pitch especially. I would hand nail unless this is majorly massive. Quote
21meyer Posted September 15, 2017 Author Report Posted September 15, 2017 51 minutes ago, C Shaffer said: Two or three nails will hold a whole sheet if this is a low pitch especially. I would hand nail unless this is majorly massive. Thanks for your reply. Just to clarify, this is a flat ceiling and not a roof. We are livestock producers and not skilled tradesmen. The floors are slats so I'm afraid that by doing it by hand we will drop nails and they will either end up falling through the slats or in the animals mouth. We have a couple thousand sheets to replace and spoken to dozens of contractors but they will not do it with animals present. Quote
wdwerker Posted September 15, 2017 Report Posted September 15, 2017 Have you looked at strip or coil fed cordless screw guns ? Quote
21meyer Posted September 15, 2017 Author Report Posted September 15, 2017 3 hours ago, wdwerker said: Have you looked at strip or coil fed cordless screw guns ? I'm not sure if the typical drywall or flooring screw guns would work because I am looking for something that would drive a fastener as flush as possible for the new overlayment. If you are referring to something different, my apologies. Quote
Tpt life Posted September 15, 2017 Report Posted September 15, 2017 11 minutes ago, 21meyer said: I'm not sure if the typical drywall or flooring screw guns would work because I am looking for something that would drive a fastener as flush as possible for the new overlayment. If you are referring to something different, my apologies. Bugle head screws wil elf dimple most steel sheet roofing and siding products if they penetrate a good ways into framing. I think you are looking for fencing nailers. They shoot ring shanked coils that bite good and don't need to be super long. I have never been in a production run where hose free benefitted enough to be worth it. Sorry. Just trying to help you brainstorm. You are likely looking into the correct tools for your application. Quote
Tom King Posted September 15, 2017 Report Posted September 15, 2017 I"d figure out a way to deal with the hose, and use a pneumatic roofing nailer. Put a couple of helpers to work as hose Grips. My bigger concern would be dropping the old screws that are coming out. Quote
drzaius Posted September 15, 2017 Report Posted September 15, 2017 43 minutes ago, Tom King said: My bigger concern would be dropping the old screws that are coming out. A good highly magnetized bit would help here. Quote
legenddc Posted September 16, 2017 Report Posted September 16, 2017 Dewalt and Ridgid have battery powered compressors that you could keep close to you and use a smaller hose. Quote
wdwerker Posted September 16, 2017 Report Posted September 16, 2017 I use standard 1/4" round shank 3" long bits in my cordless drill and then put a ring shaped strong magnet over the shank. You can slide the magnet up to the head of the screw and turn it any which way you like and the screw stays put until you take it off. With smaller screws I can have a few stuck to the side of the magnet plus one on the bit tip. https://www.kjmagnetics.com/proddetail.asp?prod=RC48 If you can only find hex shank all the way to the tip style bits then get a ring magnet with a larger diameter hole in the middle. They also offer magnets with weaker pull strength if needed. This should solve your dropping screws with animals below problem. If you are working off of rolling scaffold platforms maybe you could work from portable compressed air tanks for the nailers .It might mean more trips back and forth but you have to move a hell of a lot of 4' x 20' sheets anyway. Quote
21meyer Posted September 16, 2017 Author Report Posted September 16, 2017 5 hours ago, wdwerker said: If you are working off of rolling scaffold platforms maybe you could work from portable compressed air tanks for the nailers .It might mean more trips back and forth but you have to move a hell of a lot of 4' x 20' sheets anyway. Steve, thanks for the idea. I will give the portable air tank a try and see how many nails I can fire from one tank. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.