Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Makita 2012NB portable planer - chatter marks

Featured Replies

Hi,

I have a Makita 2012NB planer in my garage. I use it rather sporadically as I'm just a hobbyist. It has worked pretty well for me when I needed it, except that the wood always comes out with chatter marks all along it. The marks are very subtle, and mostly visible under bright light (applying Poly will make them more noticeable to the eye). Not big deal as the marks come off easily with a bit of sanding. But I keep wondering whether this is just another trade-off that come with this type of top-bench planers, such as snipe, or there is actually something wrong with my unit.

I appreciate anyone who might be able to cast some light on this issue. 

 

 

  • Author
43 minutes ago, wtnhighlander said:

The nature of the cutterhead means that the knives make a scooping cut as the board passes under. A slower feed rate (if possible) can help, but will never totally eliminate such marks. Remember, the planer is a rough milling tool, not a finishing tool.

Thank you for the clarification.

I have the older version of this one. Sharp knives obviously help as well as running with the grain. Running the boards through the other way there is always a better side to running the boards. 

I have the same unit. Haven't had this issue much, but yeah I'd certainly think about replacing the blades, then I'd be watching my depth of cut and trying to get the grain direction right (I struggle with this). As I'm dialing in my thickness, I tend to get where I'm taking off 1/4 turn of the crank at a time, or so. I do this to get the thickness and surface right and also, when removing some specific defect, I don't want to over-cut and waste material. At least in my process, running boards through a bunch of times, ultimately doesn't add much overall time to a project.  

Does the board go thru the planer at a constant rate? you can clean the rollers with mineral spirits to give them a better grip on the board and +1 to the above, sharp knives and a light pass will help.

Wood coming off the planer, or jointer, is NOT ready for finishing. Even the best planer still leaves a surface that needs sanding.

Welcome to the forums

Like everyone mentioned you still need to sand.  The surface that comes out of my planer is pretty nice and I still start at 80 grit and work through my grits to 180 before finish.

  • Author
3 hours ago, treeslayer said:

Does the board go thru the planer at a constant rate? you can clean the rollers with mineral spirits to give them a better grip on the board and +1 to the above, sharp knives and a light pass will help.

Yes it does run at a constant speed. I failed to mentioned that I did go through all the basic troubleshooting steps, such as cleaning rollers, changing knives, etc. What I'm getting from comments here is that it is normal to have a bit of chatter, which is what I suspected. I just wasn't sure as I'm no expert. 

If your taking about a wavy surface that's uneven then it might be from a board that's not pushed flat on the beds. If your taking about evenly spaced knife marks then it's normal. 

My planer will give me the weird wavy surface if it don't flatin the face first.

Aj

 

6 hours ago, Unknown craftsman said:

If your taking about evenly spaced knife marks then it's normal. 

I don't think thats normal, or i've been lucky with the planers that i have owned. the boards that come out of my DeWalt 735 are flat with no knife marks at all.

I've ran the Makita also and never had that problem, i think there is something going on that is causing the problem.

  • Author

I'm confused now, some people claim that's the way it is with planers, some claim they don't have this issue at all. Which one is it? <_<

  • Author
1 hour ago, treeslayer said:

I've ran the Makita also and never had that problem, i think there is something going on that is causing the problem.

Assuming you sand after using the planer, is it possible that you haven't noticed it? These marks are not evident unless you are really looking for them. 

11 hours ago, Chet said:

It might help if you post a picture of a piece that you have run through your planer so we can see what you are talking about.

This again.  If we can see what you are referring to, it would be a lot easier to help you determine if it is normal or unusual.

  • Author
6 minutes ago, Chet said:

This again.  If we can see what you are referring to, it would be a lot easier to help you determine if it is normal or unusual.

Good point. Will post one today when I get home

1 hour ago, danik4343 said:

These marks are not evident unless you are really looking for them

if they were there i would have seen them, i start sanding at 150 grit and work to 180 usually.

I think I have the same planer.  Yeah, they leave a bit of scalloping and the feed rate is not adjustable, just the nature of the beast.  I just use it how it was intended, to make thick stuff thinner and to get the opposing faces parallel.  Not too much gets put together right after the planer (maybe shop projects).  It is a machine used more at the start of the process, many steps to go after it goes through the machine.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.