JohnG Posted February 8, 2025 Report Posted February 8, 2025 Glad you are liking it. Similar story from me, the form factor will be a problem in many shops, but it was just right for mine. 1 Quote
Beechwood Chip Posted October 22 Author Report Posted October 22 On 1/30/2025 at 10:40 AM, Beechwood Chip said: Wanted to follow up now that I've had a chance to use the Harvey G-700. So far, I've been very happy with it. 18 months later, I'm a little less happy. The weird footprint and layout works great in my shop, and it would have been difficult for me to fit a standard cyclone. My main annoyance is with the startup time. I'm thoroughly conditioned to do all my setup and positioning, turn the tool on, make the cut, and turn the tool off immediately. if I'm batching parts out I might leave the tool running, but that's rare. I use the iVac system to automatically turn on the DC and open the appropriate blast gate when it senses the tool start up. That takes a second or two. As a result, when I use the table saw (for example) I'm usually turning the saw off just as the Harvey hits 1/2 power. I think it works best in a shop that leaves it running all the time. I tried dialing back the power to a quieter setting, but couldn't find one where I was satisfied with both the power and the noise. One solution would be to carry a remote and train myself to turn on the DC when I start setting up the tool. I'm not going to replace it, because it works well and fits in my shop nicely. But I wanted to pass that along. 2 Quote
pkinneb Posted October 22 Report Posted October 22 On 10/22/2026 at 1:09 PM, Beechwood Chip said: ... One solution would be to carry a remote and train myself to turn on the DC when I start setting up the tool. That's what I do and have found it to work well in my work flow. (not that it would matter but mine is an Oneida system) 1 Quote
Beechwood Chip Posted October 22 Author Report Posted October 22 On 10/22/2026 at 2:27 PM, pkinneb said: That's what I do and have found it to work well in my work flow. (not that it would matter but mine is an Oneida system) Thanks for the encouragement! I'll see if I can reprogram my brain. 2 Quote
Popular Post gee-dub Posted October 23 Popular Post Report Posted October 23 On 10/22/2026 at 11:09 AM, Beechwood Chip said: One solution would be to carry a remote and train myself to turn on the DC when I start setting up the tool. I've got a remote in my apron pocket and one velcro'd to the top of each bandsaw. The bandsaws are each centralized near a group of machines so just in case I don't have my apron on I can just reach up and slap the remote that is closest. This does nothing for your startup time issue. I do tend to leave the cyclone running if I am milling parts. I just open and close gates as I move from machine to machine. It always feels good though when I shut things down and pull off the ear muffs. 3 Quote
Mark J Posted October 23 Report Posted October 23 Would it be easier to wait a few seconds before beginning the cut? Quote
Popular Post Beechwood Chip Posted October 23 Author Popular Post Report Posted October 23 On 10/23/2026 at 8:46 AM, Mark J said: Would it be easier to wait a few seconds before beginning the cut? Absolutely! I could put a sign to remind me until it becomes habit. But, I think I found a better solution. It's mostly a problem on my table saw, and I just hot glued an iVac remote next to the Sawstop power switch. So, I'll turn on the saw and the DC, and the DC can spool up while the saw is booting. I have to wait for the saw to boot anyway. 4 Quote
Popular Post Ron Swanson Jr. Posted October 23 Popular Post Report Posted October 23 On 10/23/2026 at 8:41 AM, Beechwood Chip said: Absolutely! I could put a sign to remind me until it becomes habit. But, I think I found a better solution. It's mostly a problem on my table saw, and I just hot glued an iVac remote next to the Sawstop power switch. So, I'll turn on the saw and the DC, and the DC can spool up while the saw is booting. I have to wait for the saw to boot anyway. Funny how the simplest solutions are usually the most effective. 3 Quote
Beechwood Chip Posted October 23 Author Report Posted October 23 On 10/23/2026 at 3:09 PM, Ron Swanson Jr. said: Funny how the simplest solutions are usually the most effective. And the most obvious ones are often the hardest to come up with. 1 1 Quote
Popular Post wtnhighlander Posted October 24 Popular Post Report Posted October 24 11 hours ago, Beechwood Chip said: I have to wait for the saw to boot anyway. ... said Roy Underhill, never. 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.