Popular Post Beechwood Chip Posted September 17, 2025 Popular Post Report Posted September 17, 2025 I'm making some cambered clamping cauls for a glue-up where I can't get a clamp into the middle of the piece. I figure I'll keep these around for future glue-ups. 9 out of 10 YouTubers (including Marc) say to just cut a straight sloped line from the center out to either end, using a table saw, jointer, or hand plane. A couple people used a jig to bend the caul slightly and cut a straight line on the bent caul. When the caul is released from the jig, it will be curved, and the curve will become straight when it is clamped and bent again. It seems to me that the straight line method will only apply pressure at the center and ends. I'm inclined to go with the bending jig method. But maybe I'm just wasting time and effort. 9 out 10 YouTubers can be wrong, but it's just as likely that I am. Any thoughts? 4 Quote
Von Posted September 17, 2025 Report Posted September 17, 2025 I'm no expert but what I did was do to more of a curve with a hand plane from the center out. So a little near the center, only a little more at first and then a lot more close to the edges. Just what seemed to make sense to me for the reason you give. 2 Quote
Popular Post gee-dub Posted September 17, 2025 Popular Post Report Posted September 17, 2025 On 9/17/2025 at 3:30 PM, Beechwood Chip said: I'm making some cambered clamping cauls for a glue-up where I can't get a clamp into the middle of the piece. I figure I'll keep these around for future glue-ups. Absolutely useful for me. I made some out of leftover pecan from a kitchen project. Every bit as useful as they say they are. 5 Quote
Popular Post Beechwood Chip Posted September 17, 2025 Author Popular Post Report Posted September 17, 2025 I was going to use 1-1/2" square whitewood, because that's what I have and I'm trying use up my lumber stash. How important is it to use hardwood? 3 Quote
Popular Post wtnhighlander Posted September 18, 2025 Popular Post Report Posted September 18, 2025 The 1-1/2 whitewood may flex a bit more than a stiffer hardwood, but that just means the clamping force should be distributed across the entire span with less effortfrom the clamps at each end. 4 Quote
Popular Post Mark J Posted September 18, 2025 Popular Post Report Posted September 18, 2025 I'm thinking one could use a belt sander (preferably a stationary one) to make the cauls. Draw a curve on the wood, then sand down to the line. 3 Quote
gee-dub Posted September 18, 2025 Report Posted September 18, 2025 On 9/18/2025 at 6:28 AM, Mark J said: I'm thinking one could use a belt sander (preferably a stationary one) to make the cauls. Draw a curve on the wood, then sand down to the line. Quite true. I still have a smaller set made this way at the edge sander out of maple. 2 Quote
Mark J Posted September 18, 2025 Report Posted September 18, 2025 By the way, @gee-dub, how did you use the router table to make your call? Free hand or is there a jig? 1 Quote
Popular Post Immortan D Posted September 18, 2025 Popular Post Report Posted September 18, 2025 3 Quote
Popular Post Beechwood Chip Posted September 18, 2025 Author Popular Post Report Posted September 18, 2025 I'm probably over-thinking this, but I figure that if I want even pressure along the entire length of the caul, then the curve has to match the curve that the wood takes when it is bent. So, I'm reluctant to cut an arbitrary curve. I was going to use a jig like this. The screw in the middle pulls the stock into a curve, then I'd cut a straight edge in the curved stock. That way, the edge is curved when the caul is straight, but the edge is straight when the caul is bent (if that makes sense). https://www.lumberjocks.com/threads/how-to-make-cambered-cauls.304986/ 3 Quote
Popular Post gee-dub Posted September 18, 2025 Popular Post Report Posted September 18, 2025 @Beechwood Chip I agree that this is another valid method. It is easy to overthink some things. Back when Bowclamp was around I pulled my arc from their well tested products. I have a lot of clamps and prefer to use multiple clamps when the situation allows since I have more control over the tension along the line. I primarily use bowed cauls to reach out into deep areas on carcasses and they work great for this. They also allow you to clamp a long line with only a couple of clamps but in practice I do not do this much. I would be glad to measure mine if anyone is interested. Just more blah-blah to factor into your decision-engine from a guy who talks too much 3 Quote
Popular Post pkinneb Posted September 18, 2025 Popular Post Report Posted September 18, 2025 On 9/18/2025 at 8:28 AM, Mark J said: I'm thinking one could use a belt sander (preferably a stationary one) to make the cauls. Draw a curve on the wood, then sand down to the line. That's how I di mine. 4 Quote
Popular Post Von Posted September 19, 2025 Popular Post Report Posted September 19, 2025 On 9/18/2025 at 10:17 AM, Beechwood Chip said: I'm probably over-thinking this... I don't know you are overthinking it, but you have put in more thought that I did. Just a data point :-) 2 1 Quote
Von Posted September 20, 2025 Report Posted September 20, 2025 On 9/18/2025 at 10:17 AM, Beechwood Chip said: I figure that if I want even pressure along the entire length of the caul... I thought about it more :-) When I made my cauls, my thinking was I absolutely needed the caul to apply pressure in the center because that is where I couldn't reach with other clamps. If it wasn't consistent out to the edges, I could always apply more clamps there easily enough. So I think it's ideal if you get even pressure, but when I made it I err'ed on the side of getting pressure in the center. Semi-related: I watched Shannon Rogers's bench build video recently and for his lamination he did a kinda of spring joint by taking a couple of passes with his hand plane in the center of his boards so that the edges would connect well without gaps. If you did something like this, then center pressure becomes more critical and more sufficient since the edges will kinda take care of themselves when you get the center pulled tight. 2 Quote
Popular Post Beechwood Chip Posted September 20, 2025 Author Popular Post Report Posted September 20, 2025 I am gluing 4' x 8' sheets of OSB and particle board together to make a thicker sheet. I figured that I'd need 48" cauls since my clamps would only work close to the edges. Usually, cauls are used to keep a panel flat, and the gluing pressure is side to side, across the panel. In my case the gluing pressure is through the thickness of the panel. But, I just realized that I was thinking about this all wrong. I'm cutting the sheets down to 2' x 4', so I only need 24" cauls. At 24", the exact distribution of the pressure is less of an issue. I'll just pop a couple playing cards under the center of the caul and call it done. 5 Quote
Von Posted September 20, 2025 Report Posted September 20, 2025 I wasn't thinking about something that would flex and needed to be kept flat as well as clamped together. I agree with your thinking. As I get older (and hopefully a little wiser) I find it is worth spending more time getting the problem well defined. Caveat: do as I say, not as I do... 1 Quote
Ron Swanson Jr. Posted September 20, 2025 Report Posted September 20, 2025 @Beechwood Chip What is the project going to be? 1 Quote
Popular Post Beechwood Chip Posted September 20, 2025 Author Popular Post Report Posted September 20, 2025 On 9/20/2025 at 11:42 AM, Ron Swanson Jr. said: What is the project going to be? I have a Centipede that I use for breaking down sheet goods. With my arthritis, I don't want to work on the floor. I used to use a sheet of OSB to create a work surface, but accidentally set my circular saw depth wrong and cut through it. Plus, it was a pain to haul the big sheet around. I also had four 2' x 4' x 3/4" sheets of particle board, so my plan is to glue the particle board to the OSB to make a thicker panel that I'm less likely to cut through. I figure the 2' x 4' pieces should be easier to haul around. 3 Quote
Ron Swanson Jr. Posted September 20, 2025 Report Posted September 20, 2025 Sounds like a good plan, sir. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.