Andrew Pritchard Posted June 14, 2012 Report Posted June 14, 2012 I am a hobbyist on a *VERY* tight budget for new toys equipment. One of the things I've been looking at is a dado blade for my table saw. I've seen a cheaper blade - a wobble dado blade and was wondering what the differences are between that and the stacking dado sets that seem more popular. Obviously wobble blades are cheaper - I've seen one for about $50 CDN. The cheapest stacking dado I've seen is $99 CDN. So I guess my questions are: What is the difference in outcome? Am I more likely to stress my table saw with one type more than another? Are wobble blades prone to failure in a way the stacking blades are not? Quote
PaulMarcel Posted June 14, 2012 Report Posted June 14, 2012 I haven't used a wobble, but wasn't interested in one. If the blade is basically oscillating side to side to make the groove, it is leaving a rounded bottom on that dado. If the end of the dado is exposed (say, at the shelf-side joint), you'll see a crescent-moon shaped gap. I know Oshlun makes a less expensive 6" dado stacks. A 6" stack is less load than an 8" so if you have a smaller contractor saw, you'll get better performance. I got one long ago on a black friday sale for $25 (which is nuts). Another thought. I have an 8" stack, but only use it in 2 configurations: 1/4" and 1/2" stack because I use a KM-1 to exactly size the groove to the tenon or captured stock. You use two passes to get the exact fit. It is a heck of a lot faster than monkeying with other chipper blades and shims to get it exact; that only pays off if you then run many many grooves to amortize the time spent on the monkeying process. The KM-1 isn't cheap, either, but the idea is that you could just get a 1/4" blade set and do your grooves in 2 passes. If they are wider than 1/2" (two 1/4" passes), do a third to clean the middle. You can get finger-joint or box-joint blades from Freud (IIRC) that are basically the outer blades of a dado stack; oriented one way, you get a 1/4" kerf, reversed, you get 3/8" kerf. That's a cheaper possibility. To answer your last question, wobble blades to me are nearly 99% prone to failure because I wouldn't want to accept a rounded-bottomed dado being exposed. Quote
knotscott Posted June 14, 2012 Report Posted June 14, 2012 The terms "wobble" and "table saw" just don't seem like they should be used in the same phrase together. You'll nearly always get better results from a stack for the reasons Paul mentioned. Even the HF stacked dado set for $30 should do better. Sometimes Ebay has cheap sets. Whichever you get, get one with carbide teeth....steel is cheaper but won't hold up long at all. A router bit is a cheaper way to go if you own a router. Quote
Guest Posted June 14, 2012 Report Posted June 14, 2012 I actually have both types. My first was the wobble type and if memory serves, and at times that is a stretch, it left the bottom of the dado a little uneven. After spending a great deal of time tuning my table saw and working with a new link belt to remove all the vibration possible, I just could not bring myself to put that wobble thing back on it. I think if you go with a 6" stack set you will be much happier. I also like the router as often as possible. Quote
Lgifford46 Posted June 14, 2012 Report Posted June 14, 2012 If you wait for the sale,Canadian Tire puts their 8" set on sale for half price every couple of months. Not professional grade but pretty decent cuts in plywood and solid . I use mine quite a bit and am always content with the results. Quote
Jim Heinbuch Posted June 15, 2012 Report Posted June 15, 2012 I got a Canadian Tire 6" set on sale for about $50. I don't know if I've seen a Canadian Tire 8" set, but that doesn't always mean much. I haven't seed any at Princess Auto but it might not hurt to check if price is an important part of the consideration. BTW, I used 6" Craftsman wobble blade until a screw reconfigured the carbide teeth. Quote
Jerry_in_SD Posted June 16, 2012 Report Posted June 16, 2012 If you own a router, you can always clean up a wobble dado blade cut using one of those clean up bits. I would say use a router plane (hand tool) but the only ones I am familiar are the Lie Neilson and they alone cost as much as a stacked dado set. Quote
wdwerker Posted June 17, 2012 Report Posted June 17, 2012 I have an interesting scar on my fingernail thanks to a wobble dado! Cheap stacked sets have drawbacks as well. Some of the sets leave a raised rougher area between the outer blades. Shop wisely! Quote
SandSWoodcraft Posted June 18, 2012 Report Posted June 18, 2012 I tried the HF dado stack when I first got my table saw and it was absolute garbage (took it back). I've currently got the Freud Diablo set sold at home depot. I don't think it's all that good after seeing the flat bottoms I'm getting with my infinity flat tooth blades, but even I can't bring myself to spend the $300 for a dadonator (yet). I think if I had to do it all over again it would just use a pattern bit and Marc's perfect fit dado jig with a router, saving my money for the dadonator. Quote
knotscott Posted June 18, 2012 Report Posted June 18, 2012 I tried the HF dado stack when I first got my table saw and it was absolute garbage (took it back). I've currently got the Freud Diablo set sold at home depot. I don't think it's all that good after seeing the flat bottoms I'm getting with my infinity flat tooth blades, but even I can't bring myself to spend the $300 for a dadonator (yet). I think if I had to do it all over again it would just use a pattern bit and Marc's perfect fit dado jig with a router, saving my money for the dadonator. Good news! The Dadonator is currently $210 for the 8", and $190 for the 6"....free s/h. I marvel at the cuts every time I use it. Quote
Gary Posted June 19, 2012 Report Posted June 19, 2012 +1 on the Oshlun dado set. I am very happy with the quality of this set for the money. Very flat bottoms, but there is a slight bat ear issue... Nothing out of the ordinary, though. Quote
Andrew Pritchard Posted June 23, 2012 Author Report Posted June 23, 2012 I've decided to get some bushings for my router instead. I feel at this stage dado stacks are a bit of a one trick pony, and bushings will let me do more aside from cutting dados. Dado blades are still on my list, but for now a set of bushings will let me cut dados as well as learning to do inlays, etc. And the bushings were cheaper than the wobble blade. Bonus! Quote
JMort847 Posted July 8, 2012 Report Posted July 8, 2012 Peachtree runs the Fulton set for half off periodically. I picked up a set for around $60 with carbide-tipped blades. I've used them a few times on veneered plywood and was pleased with the results - nice cut with no tearout. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.