Recommended Posts

Posted

All this talk about dust collectors on the forum lately has got me redesigning a few problem areas in my shop. Task one is to improve the DC on my router table. I currently use only the 2.5" port on the fence.

I want to encase the router table on all sides (and the bottom), and put a plexiglass door on the front panel to access the router. The back panel will get a hole (either 4 or 5 inches) to accept an appropriate adaptor. Then I will collect from both the cabinet and fence at the same time. This should really capture the dust.

My questions is, should I totally enclose the cabinet or should I leave gaps/intakes for air? I am worried if I totally seal the cabinet it will it choke the dust collector as it tries to suck the dust from the cabinet box.

Posted

You should fabricate some type of adjustable vent to moderate air flow based on your operations. Take a look at the box unit Rockler offers for sale as an idea. I mounted one in my table and have been happy with the results. Good luck!

  • Like 1
Posted

I built a dustbox around my router. Has a 4" port to the box. There are two 2.5" ports on the box as well so I hookup a short stub of hose from the box to the fence; the other hole has a "blast gate" for 2.5" hose (cannot remember where I got it, likely Rockler). Use that to modulate the airflow. The two 2.5" equal the 4" more or less so the air flow to the fence and modulation hole flow through the box to grab the dust. The box is always clean and I never have anything to speak of on the table.

I did a video tour of the DC hookups on my tablesaw, which has the router table in the right wing. You'll see some details there though I did add the second 2.5" port w/modulation later and it made a big difference. Router never gets warm in there either with that airflow. Put tape over the switch to keep dust out and squelch the manufacturers repair profit center :)

  • Like 2
Posted

I am pretty sure it is like a unicorn.... it just doesnt exist.

Don't you DARE say Unicorns don't exist. That's just not right!

  • Like 1
Posted

One thing to keep in mind, is once you enclose the router, make sure you always use it with dust collection running. This is to keep the router from over heating.

Posted

I tried putting the shop vac exhaust into the front of my router table cabinet to help blow the dust out the back. Suction was split between the fence and the back . The concept worked great but the router and the lift plate got hot pretty quick, so end of that experiment. Might try and find some powerful little computer fans to mount in the door. I think incoming air is important to dust collection and router cooling.

At the IWF show I saw a flexible collar that fits between the router and the bit with a hose and a tee for the fence hose. Got on the mailing list, I think he had some in production and patent pending on one for the miter saw.

Posted

You know the deal there Steve....not enough air flow and the router heats and suffers. I use a Grizzly 1.5 HP DC that I found at a flea market for about half the price of a new one and it was basically new. I've since looked on Craig's list and DCs are everywhere and they're cheap. I'm toying with making a Thein separator that fits on a trash can and use a fan unit (squirrel cage) out of a package unit air conditioner. A HVAC guy you know would give or sell you one for $10 out of a defective unit. You could recirculate the air or blow it outside.

  • 3 weeks later...
Posted

Well I decided not to enclose my router table (for the time being). After watching Marc's video on the new Festool router table, I decided I would try something similiar. I attached the dust shroud under the table, and combined it with the fence port on the table. I think this will work well, so I'm going to try it for a while and see how it goes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined