jmaichel Posted May 21, 2013 Report Posted May 21, 2013 Yesterday I used a dado stack for the first time! I think my heart skipped a beat when I first ran a board over the stack. I went slow and took a 1/2" in three passes. Very happy with the quality of the cut from the BORG Diablo for $99 (actually $90) I got 10% off. Just wanted to share Quote
STL Woodguy Posted May 21, 2013 Report Posted May 21, 2013 I am a fan of dado stacks/blades, and I think other than for specialized cuts like stopping dados, dados via routers are a bit overrated. I've had more problems with tearout and whatnot (even with quality bits, backers or taking minimal passes) on the router than with the dado blade, it just makes such a clean cut. The only bummer being having to swap the stack in on the saw (one argument for the router), but if you have a lot to cut, not a big deal and an efficient way of doing it. Quote
Popular Post Eric. Posted May 21, 2013 Popular Post Report Posted May 21, 2013 Dado stacks always make me nervous. They make you nervous when you're using them, or the thought of using them makes you nervous? Did you use them before they were outlawed in UK? Because until I heard other people act like they're so dangerous, I never even thought twice about them. It's just a table saw blade, only wider. I'm perfectly comfortable using a dado stack, and honestly, I get buttpucker way more often at my router table. 6 Quote
Freddie Posted May 21, 2013 Report Posted May 21, 2013 I only get nervous when my father uses the tablesaw. He launched a board off the table 15 feet across the room and went clean through the window. Although i could not stop laughing, the thought of him using that saw makes me ill. Quote
jmaichel Posted May 21, 2013 Author Report Posted May 21, 2013 It was more or less first time jitters than anything. I see how useful they are and many more uses of the dado stack in my future. Quote
dwacker Posted May 21, 2013 Report Posted May 21, 2013 It was more or less first time jitters than anything. I see how useful they are and many more uses of the dado stack in my future. Dont sweat it a little fear is healthy. You will get used to it in no time. Quote
Freddie Posted May 21, 2013 Report Posted May 21, 2013 The first time i ever used a table saw back in 2008 i was super afraid of the thing. I dont remember how long that lasted but over time it was replaced by comfort and respect for the power of the tool. Same thing went for the first steep roof i walked, i was so nervous i almost slid off. Now im a monkey up there Quote
TerryMcK Posted May 21, 2013 Report Posted May 21, 2013 Eric my experience was about 25 years ago when my step dad sliced 3 fingers off at the knuckle with a dado set. There was only hamburger meat left and nothing to sew back on. If he had the same cut on a regular blade he may have had a chance to have had them sewn back on. That's why I get nervous. Quote
Eric. Posted May 21, 2013 Report Posted May 21, 2013 Eric my experience was about 25 years ago when my step dad sliced 3 fingers off at the knuckle with a dado set. There was only hamburger meat left and nothing to sew back on. If he had the same cut on a regular blade he may have had a chance to have had them sewn back on. That's why I get nervous. Well it's certainly understandable that would stick with you. But the truth is, a dado stack is just one of many spinning chunks of sharpened steel in our shops. If we use our noodles and treat it with respect, it's no more dangerous than many of the other medieval torture devices we use without hesitation. I'm fairly certain my half inch spiral bit could turn a digit into hamburger meat, too. Quote
jmaichel Posted May 22, 2013 Author Report Posted May 22, 2013 Dont sweat it a little fear is healthy. You will get used to it in no time. Eventually I will get used to it. The Grr-Ripper is my new best friend during these dado operations. I also just placed a large order for a bunch of magswitch stuff to help keep me safe in the shop. Quote
Byrdie Posted May 22, 2013 Report Posted May 22, 2013 I use my dado on a regular basis and love using it. Much easier to set up compared a router. For me, more consistent, and, with some planning and foresight, no more or less hazardous than any other tool. Need to think about the same things you do with any other sharp tool. Consider all the exit points and how to avoid them, wait for the blade to stop spinning before approaching it, make sure it is properly fitted and prepared before turning it on and be sure to use push sticks, featherboards and other setup tools when applicable during operation. Quote
tim0625 Posted May 24, 2013 Report Posted May 24, 2013 Eric my experience was about 25 years ago when my step dad sliced 3 fingers off at the knuckle with a dado set. There was only hamburger meat left and nothing to sew back on. If he had the same cut on a regular blade he may have had a chance to have had them sewn back on. That's why I get nervous. Yep, that would do it. Sorry for dad but like others have said, use the same safety precautions and always keep that healthy respect for tools - corded AND uncorded!! and you'll be fine. I see the guys on Woodsmith shop always take the full cut in one pass. That works ok if you move slowly through it and your stack is always sharp. Quote
wdwerker Posted May 24, 2013 Report Posted May 24, 2013 I always approach a dado or other kickback possible cuts on the tablesaw by planning my path, where I am gong to put my hands , where is the push stick before I start and most importantly where will I stand out of the way . I plan an exit strategy as well, if something binds, sticks or just feels like something is going wrong I let go and step further aside in one planned fluid motion. Sure I have ruined a board , blade or sheet of plywood but it beats a trip to the hospital. Quote
dwacker Posted May 24, 2013 Report Posted May 24, 2013 I prefer push blocks just like the jointer for dados and most sheet good work. Quote
knotscott Posted May 24, 2013 Report Posted May 24, 2013 The roar of a full dado stack always reminded me of an airplane prop, and definitely freaked me out a little bit at first., Those molding head cutters are no less intimidating. The Gripper is a great tool for dados. Quote
Slick218 Posted May 24, 2013 Report Posted May 24, 2013 I always approach a dado or other kickback possible cuts on the tablesaw by planning my path, where I am gong to put my hands , where is the push stick before I start and most importantly where will I stand out of the way . I plan an exit strategy as well, if something binds, sticks or just feels like something is going wrong I let go and step further aside in one planned fluid motion. Sure I have ruined a board , blade or sheet of plywood but it beats a trip to the hospital. This is very true, there is only one wrong way to machine parts - the one where you get hurt Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.