rodger. Posted July 7, 2013 Report Posted July 7, 2013 I have read a lot about the bevel up smoothers, and about their pros (easy angle changes) and cons (harder to adjust on the fly). I was looking for a few opinion on a smoother, specifically. I have the LA block, and LA jointer from veritas and really like them. I was wondering if the smoother was worth the investment, as I already have the standard veritas #4. I like my smoother, but I am not "wowed" by it like I am with the BU jointer plane (probably an unfair comparison). Quote
jhl.verona Posted July 7, 2013 Report Posted July 7, 2013 I can't help directly because I don't yet own one. I'm seriously thinking of getting the Veritas Bevel Up Smoother, with an extra two blades. I think the size puts it in the 4 1/2 category, rather than a 4. My reasoning is that it's a 'big' block plane, and I've had a lot of success on awkward woods with the block, using a high angle blade (50°). I can tell you that they sell second hand for very high prices - I've been trying on ebay.co.uk for months and they all seem to keep about 75%-85% of their price. Every time I get sniped... I apologise for being on the wrong side of the fence, but I'd like to hear those opinions too! John Quote
TerryMcK Posted July 7, 2013 Report Posted July 7, 2013 I have the small Veritas bevel up smoother. It's about the size of a #3 and is fairly light weight. It is awesome despite being small. I have only the stock blade, giving around 37 degrees, have found it very useful for end grain and general smoothing. I have yet to buy the additional blades that give higher angle bevels for more difficult timbers. I think the additional weight of the larger one would lessen the risk of chatter but I've not seen much, if any, chatter anyway on the smaller model. Overall it is a good buy and is up there with the best. 1 Quote
rodger. Posted July 7, 2013 Author Report Posted July 7, 2013 I have the small Veritas bevel up smoother. It's about the size of a #3 and is fairly light weight. It is awesome despite being small. I have only the stock blade, giving around 37 degrees, have found it very useful for end grain and general smoothing. I have yet to buy the additional blades that give higher angle bevels for more difficult timbers. I think the additional weight of the larger one would lessen the risk of chatter but I've not seen much, if any, chatter anyway on the smaller model. Overall it is a good buy and is up there with the best. I think I may get this conversion kit to convert my block into small smoother as well. Should also be good for end grain tasks as well.http://www.leevalley.com/en/wood/page.aspx?p=41715&cat=1,41182,41189,41715 Quote
woodbloke Posted July 8, 2013 Report Posted July 8, 2013 I have the an almost complete line up of Veritas BU bench planes, the long try, jack, wide smoother and the little narrow one recently introduced. I used all sorts of BD planes for decades ( I still have my Norris A1 panel plane) but you realise the versatility of BU planes once you start to use them. I won't use anything else now - Rob 1 Quote
tirebob Posted July 13, 2013 Report Posted July 13, 2013 I have a fair amount of smoothing planes, as well as a ton of others. LN #3, Vintage Stanley #4, Vintage Stanley #4.5 as well as a Veritas BU Smoother (not the smaller one). I must say that the BU smoother is buy far my favourite plane period! That sucker has never let me down and it is soooooo easy to set up and use it is ridiculous. It easily tames even the most gnarly grained woods... A nice feature for me too is that I also have the Veritas LA Jack and LA Jointer, and as these three planes all use the same blade, I just keep them all sharpened at different angles (25, 38 and 50 degrees) and just swithch them between the various planes as needed. Very convenient!!! As for the complaint of the lack of adjustability on the fly compared to Baily styled planes, it has never created even a remote issue for me. It takes me maybe an extra 1 or 2 seconds to adjust on the fly and that by no means interferes with my work. That isn't any sort of knock on Baily style planes as they obviously do great work as well, but really, for me I find the BUS so much simpler and easier to use. Don't hesitate to try and buy one of these for sure! Quote
CessnaPilotBarry Posted July 13, 2013 Report Posted July 13, 2013 I used my Veritas BU smoother all day yesterday, planing knarly, curly and brittle QSWO with a high angle setup. This stuff was so difficult, the curls burned in my drum sander, and the reversing was impossible to surface with machines and with lower angle planes. Years ago, I might have given up on this stuff and torched it, but since the BU laughed at it, I'll have a few cool boxes. 1 Quote
lemonjello Posted July 24, 2013 Report Posted July 24, 2013 pug, I have the (truth!) smoothie, jack and jointer, biggest benefit is the blades are all the same! Get a spare 25, the 38 and 50 and maybe a toothie and you are set for anything! I just got a couple PMV11 blades and they are the heat! They stay sharp for quite a long time! the 50 in the BU smoothie is the only plane I can reliably use on curly koa. feels like driving with the brakes on, but it works! I've got a bronze LN #4 that rarely leaves the shelf now, since I got the smoother. No experience with the smaller BU smoother Quote
Llama Posted July 24, 2013 Report Posted July 24, 2013 I just received my Lie-Nielsen 62. It's a bevel up Jack plane. Probably very similar to the Veritas version in design. I love this plane! Simple to adjust. Just loosen the front knob, and push the slider to change mouth opening. I was planing out of the box, with hard maple. Shot a rough edge, jointed and smoothed the face. All with the one plane with only a simple blade and mouth adjustment. There was an article in Fine Woodworking with someone, showing how to use the plane. They were bold enough to say that this is the only plane you need. Quote
rodger. Posted July 24, 2013 Author Report Posted July 24, 2013 Do you guys use the "ruler trick" when sharpening your bevel up planes? Quote
CessnaPilotBarry Posted July 24, 2013 Report Posted July 24, 2013 Do you guys use the "ruler trick" when sharpening your bevel up planes? I don't use it at all... I understand the concept, but I do my flattening and main bevel shaping on diamond plates, so I haven't had the need for the ruler trick. Quote
lemonjello Posted July 28, 2013 Report Posted July 28, 2013 There was an article in Fine Woodworking with someone, showing how to use the plane. They were bold enough to say that this is the only plane you need. I just reread that issue last night! Was Christian Becksvort, neat idea, but I do too many things at the same time. Flatten, joint, shooting would be a pain to switch blades a lot. Maybe good for travel to a class though. Less to carry. Quote
Llama Posted July 28, 2013 Report Posted July 28, 2013 I just reread that issue last night! Was Christian Becksvort, neat idea, but I do too many things at the same time. Flatten, joint, shooting would be a pain to switch blades a lot. Maybe good for travel to a class though. Less to carry. That was my thought! Eventhough the plane is very easy to setup, it would be a pain to keep switching. On a related note, I am thinking about buying another one. I know the bevel-up smoother and jointer are on my short list. Quote
lemonjello Posted July 29, 2013 Report Posted July 29, 2013 I find that I use the Jack plane quite a bit. Works great as a shooting plane too. I use it to size and joint smaller pieces rather than using the jointer plane. If you're a LN user, two would be sweet! I myself thought about a second Jack. Also been eyeing the small smoother. For the quality, ease and useability, I think the LV BU planes are great!! I can get back to woodworking and not fiddling around setting up a temperamental tool. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.