Llama Posted August 7, 2013 Report Posted August 7, 2013 After making my hand tool cabinet I very quickly realized that it was a little too small. It is great for my most used hand tools, but some of my larger hand tools need a better home. I remember a tool cabinet by Chris Gochnour in Fine Woodworking a few years ago, so I flipped through the archives, and found it. In keeping with the theme of my shop, I am using pallet wood, or even worse! I am making a few changes to the original cabinet to better suit my needs, such as the absence of drawers. I just don't like them for cabinets like this. I will use milk-paint for the finish with a coat of boiled-linseed oil. I will leave the inside of the back unpainted. I will likely add doors to the cabinet, perhaps with glass... Nasty pine, with nasty knots! Using my Stanley #45! I love this plane! Rough mock up, also checking my rabbet depths... Hand cut dadoes. I used the MDF as a guide for my carcass saw. I cut the line, then marked the width with the shelf stock, and moved the jig. My new router plane made very quick work of the dadoes. Stop! Same as above, but I used a chisel to define the stop. Quote
G S Haydon Posted August 7, 2013 Report Posted August 7, 2013 Nice to see the estwing creeping into shot Quote
Llama Posted August 8, 2013 Author Report Posted August 8, 2013 Small update... In the clamps! Now I am messing around with the idea of adding doors. I'll probably leave it open for access, but I may change my mind. Quote
Llama Posted August 12, 2013 Author Report Posted August 12, 2013 Lots of progress in the last few days. Two coats of Red Milk paint, applied with a foam brush. Boiled linseed oil over the Milk Paint. Edge planing the boards out of the planer. The backs were left a little rough on purpose. I really like the note I wrote on the pallet so it didn't get thrown away! Tongue and Groove with the #45. Beading with the #45. I don't need a tail vise! Inside shot. The back floats in the tongue and grooves and is nailed to the case. Inside shot, showing a cut off from the original wood. Thanks for looking! 1 Quote
Llama Posted August 13, 2013 Author Report Posted August 13, 2013 very nice Thanks! Not bad for free wood and $15 for paint Quote
Bombarde16 Posted August 13, 2013 Report Posted August 13, 2013 Thanks! Not bad for free wood and $15 for paint Proving yet again that it's not the wood, it's the working thereof. Quote
Llama Posted August 13, 2013 Author Report Posted August 13, 2013 Proving yet again that it's not the wood, it's the working thereof. Thank you! Too many guys use wood like this for prototypes, or firewood, and that is a shame Quote
Llama Posted August 14, 2013 Author Report Posted August 14, 2013 I hung the cabinet by my workbench, and put some supplies on it. Gave me a good spot for my #45 and some wooden planes I recently added to my collection. I placed some magazines and books on the bottom shelf. Also gave me a great spot for my machining parallels, which come in handy all the time! Quote
..Kev Posted August 14, 2013 Report Posted August 14, 2013 Cool looking and functional! Can't beat that! Quote
Llama Posted August 14, 2013 Author Report Posted August 14, 2013 Thanks! I want to make a taller one for another part of my shop. Maybe a different color... I love milk paint! Great stuff! Quote
G S Haydon Posted August 14, 2013 Report Posted August 14, 2013 Great stuff Mel. The beads on the edges of the boards look nice and crisp. A great use of humble timber. Quote
Llama Posted August 17, 2013 Author Report Posted August 17, 2013 Great stuff Mel. The beads on the edges of the boards look nice and crisp. A great use of humble timber. Thanks! I don't know who came up with that idea, but it's prominent in Shaker furniture. It really adds a bit of nice character. It is also functional, it allows for a bit of leeway in the joining. Kind of hides the fact of the panels not being perfect. Quote
Tom King Posted August 17, 2013 Report Posted August 17, 2013 I like it a lot! When I use a hammer, I swing an Estwing. Did you run the beads with the 45, or a molding plane? Quote
Llama Posted August 17, 2013 Author Report Posted August 17, 2013 Thanks! I used the #45 for the beads, rabbets and the tongue and grooves. Worked flawlessly! Quote
G S Haydon Posted August 17, 2013 Report Posted August 17, 2013 Thanks! I don't know who came up with that idea, but it's prominent in Shaker furniture. It really adds a bit of nice character. It is also functional, it allows for a bit of leeway in the joining. Kind of hides the fact of the panels not being perfect. Probably the British . I read a few books on the Shakers, not only about the furniture but their faith, how they lived, where they came from etc. It was interesting to see how that was reflected by the furniture they made. They were quite ingenious too, I think they were early pioneers of circular saws! I like it a lot! When I use a hammer, I swing an Estwing. Did you run the beads with the 45, or a molding plane? Estwing Quote
Llama Posted August 17, 2013 Author Report Posted August 17, 2013 Probably the British . I read a few books on the Shakers, not only about the furniture but their faith, how they lived, where they came from etc. It was interesting to see how that was reflected by the furniture they made. They were quite ingenious too, I think they were early pioneers of circular saws! Estwing Probably the British! Roy Underhiill said they (Shakers) probably invented the tablesaw! That makes it easier to justify my use of a tablesaw But as much as I enjoy their furniture, I'm not going to be celibate Quote
G S Haydon Posted August 17, 2013 Report Posted August 17, 2013 I think Roy is right, I think I was a female shaker. Will see if I can dig out some info on it. Quote
Llama Posted August 18, 2013 Author Report Posted August 18, 2013 According to Roy U, it had something to do with incorporating a sewing machine, with the movement of a saw... I don't have a book about it, I learned it from T.V Quote
Bombarde16 Posted August 22, 2013 Report Posted August 22, 2013 I think Roy is right, I think I was a female shaker. Will see if I can dig out some info on it. Cutting and pasting from Wikipedia Using thoroughly vetted academic research, we learn the following: Various claims have been made as to who invented the circular saw: A common claim is for a little known sailmaker named Samuel Miller of Southampton, England who obtained a patent in 1777 for a saw windmill.[3] However the specification for this only mentions the form of the saw incidentally, probably indicating that it was not his invention. Gervinus of Germany is often credited with inventing the circular saw in 1780 Walter Taylor of Southampton had the blockmaking contract for Portsmouth Dockyard. In about 1762 he built a saw mill where he roughed out the blocks. This was replaced by another mill in 1781. Descriptions of his machinery there in the 1790s show that he had circular saws. Taylor patented two other improvements to blockmaking but not the circular saw.[4] This suggests either that he did not invent it or that he published his invention without patenting it (which would mean it was no longer patentable). Another claim is that it originated in Holland in the sixteenth or seventeenth century.[5] This may be correct, but nothing more precise is known. The use of a large circular saw in a saw mill is said to have been invented in 1813 by Tabitha Babbit, a Shaker spinster, who sought to ease the labour of the male sawyers in her community.[6]The Barringer, Manners and Wallis factory in Rock Valley Mansfield, Nottinghamshire also claims to be the site of the invention. Quote
Llama Posted August 22, 2013 Author Report Posted August 22, 2013 Thanks for that! I didn't even think of asking Wikipedia. So, we really can't say who invented the table saw? The Shaker story is the one I want to believe Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.