Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Shop Setup

Featured Replies

Amazing how much time goes by in my life between working and having time to work in the shop....  Its September now and I last did work in the shop in April!

I guess I can call it reflection time!
Anyways I need some ideas and your thoughts as I continue to clean and set up shop proper. Here are some photos of where I am to date:

Garage15forward_zpsdf3d56f6.jpg

Garage15left_zps42280da2.jpg

Garage15right_zps14493b27.jpg

Garage15junk_zps42f141f8.jpg



 The thing I am currently debating is the wall of cabinetry. I will not have any other wall space in the garage, it is pretty much all spoken for and I am starting to wonder if I should make such a big commitment to cabinetry.... The wall opposite the garage doors is pretty much spoken for between a "garage" metal rack that is for the most part floor to ceiling with household items, paint, tools, etc. Beside that is the wooden drawers I built which is about 60% full of construction tools, etc. Above it all is a narrow aluminum shelf that stores some clear totes.

The second picture is the lumber storage wall with the plywood cart below it, besides those items are a water softener and the electrical panel boxes, so that wall is also spoken for...

The third picture is the last wall. The little bit of floor space left is under the shelving closest to the garage door. Its about 6' wide by about 4' high.

The last picture show what I have left as far as machinery to "fit" into the shop. Ideally I want to leave the shop setup for woodworking. I am open to all ideas on placement, space saving ideas, things you would do differently, etc.

I will post this on multiple sites, if you see it twice, feel free to ignore it ;-)

Thanks!

  • Author

what is the round celinders ?

The cylinders are water softener tanks. Florida water is notoriously hard.

Just be sure to lock the door when you're cutting sheet goods on your TS!

 

I love the renderings...very neat.

  • Author

Thanks, the table saw actually rolls into the center of the open space for use, I just stuck it there in the drawing to see how much space I would have when all tools were stored. I still want to be able to get at least one car in, especially when I need to do service, etc.

Chop, if wall space is such a premium, I'd seriously consider building roll-around cabinets to start with. Once you've settled in and evaluated your needs, you will be better suited to judge what would be the most effective use of the wall space.

  • Author

Chop, if wall space is such a premium, I'd seriously consider building roll-around cabinets to start with. Once you've settled in and evaluated your needs, you will be better suited to judge what would be the most effective use of the wall space.

 

Thanks TR, that is a good thought! The white cabinet that is underneath the yellowed colored ones is just that. I intended it to be a roll around tool/assembly tote. Somewhere to keep hardware, tools etc. either permanently or temporarily while working on a project. Kinda like an oversized tool bib ;-)

 

Keep the thoughts coming folks, I am currently looking at the possibility of a flip top cart for planer/miter saw.

The cylinders are water softener tanks. Florida water is notoriously hard.

 

Wait, that mineral solution that comes out of my taps is WATER? 

 

Love the renderings, and get where you're coming from on cabinets. One source of inspiration I've started digging into is the 12-gauge Garage. If you haven't seen it yet, it's here:

 

http://12-gaugegarage.com/

 

It's an auto enthusiast / welder garage, but the guy was a genius at storage, fold down worksurfaces, etc. And even if you don't get anything from it, it's a pretty cool way to waste some time.

  • Author

Wait, that mineral solution that comes out of my taps is WATER? 

 

Love the renderings, and get where you're coming from on cabinets. One source of inspiration I've started digging into is the 12-gauge Garage. If you haven't seen it yet, it's here:

 

http://12-gaugegarage.com/

 

It's an auto enthusiast / welder garage, but the guy was a genius at storage, fold down worksurfaces, etc. And even if you don't get anything from it, it's a pretty cool way to waste some time.

LOL, Hey Bob, looks like we share the same water :lol:  I have seen that website and agree, he is quite crafty. Do you belong to any of the local woodworking clubs?

Do you belong to any of the local woodworking clubs?

 

No. I don't. I'm about as east as you can get and still be considered part of Tampa Bay, and many of the clubs I've found so far are on the other side of the bay. (Which is unfortunately where Woodcraft and Rockler are too.)

 

You?

  • Author

West-most. I have toyed with the idea of going to one of the clubs, but my schedule rotates and there's is a fixed tuesday or something like that. The web has been my greatest connection to this purely hands on trade, lol :lol::P

Ain't that ridiculous...

Take a look at the tool cabinets from Wood Magazine in their Basic Built series.  It's not the skill level; it's the functionality of the piece.  Basically it's a roll around cabinet with the benchtop tools on pull out trays that clamp to another (smaller) roll around cabinet.  Pull out the "tabletop" you need when you need, put it away to keep out from under foot.

 

Looking at the plans, it looks like the table saw could be getting in the way of the door, especially if you've got the car in the way for something like an oil change, engine swap, diaper hunt, whatever.  Would you be able to swap the bandsaw with the table saw?  Store the tablesaw parallel with the wall, and roll it out when you need it.

  • Author

Moving the table saw to the area next to the bandsaw opens up more floor space:

 

Garage15_zps75e8f237.jpg

 

But I think I need to rethink this more... I need to keep more floor space open... Thanks folks on the great thoughts, I need to reassess my vertical space usage.

Is there enough room for the lumber storage by the door?

  • Author

Is there enough room for the lumber storage by the door?

If you are talking about the six panel door, that upper shelf space is held up to the ceiling with all thread, making it rather difficult to use for wood storage. It is also a narrow shelf. The major wood storage area is shown more clearly in picture two, the three shelves and the plywood cart below hold a lot of lumber. The lowest shelf right now is packed full of old 2x10 or 12's I dont recall. They have seasoned for a few years waiting on the shop design to be final - destined to be the workbench ;-)

With respect, if you're looking for more "floor space", then the lumber storage seems to be the obvious spot for change.

 

How about putting the storage high on walls to leave everything at the lower levels open?  I fought that in my shop and moved up as well.  Yes, I need to get the ladder to get material from time to time but, my floor space is much more open. 

 

I only buy sheet goods as I need them and cut them down as soon as they come into the shop.  I don't have these goods readily on hand but, I have the needed shop space.  There's got to be trade offs.

  • Author

With respect, if you're looking for more "floor space", then the lumber storage seems to be the obvious spot for change.

 

How about putting the storage high on walls to leave everything at the lower levels open?  I fought that in my shop and moved up as well.  Yes, I need to get the ladder to get material from time to time but, my floor space is much more open. 

 

I only buy sheet goods as I need them and cut them down as soon as they come into the shop.  I don't have these goods readily on hand but, I have the needed shop space.  There's got to be trade offs.

The lumber rack is high, first shelf starts at 5', 6' and last one at 7' (its on the left side above the lumber cart).  I understand your argument and it is a good one, however, I already have the plywood cart ;-)  The other thing is that I do keep sheet stock on hand for various projects and it has come in handy many times. I also have leftover sheet goods from projects that I would not be throwing out which is why I built the cart ~ 2 years ago. The cart has open area in between the A frame which allows for even more storage of either sheet or solid stock. I appreciate the thoughts, I am just trying to squeeze every bit of performance before I start cutting more material to build the interior of the shop.

 

Currently I am tossing about whether to just commit to the original design which has ample storage space and just leave the shop setup for work at all times, only nesting everything for the occasional car maintenance or garaging of a vehicle. I am going to play with a few more designs just to see what comes up.

the center area of the plywood cart can be used for storage of hand held power tools, whether they are for the car or the wood shop.  If your air compressor is small enough, it might be able to live there.  You could also relocate your clamps to that space, and dedicate some space to extra lumber storage.  (Assuming there's an open center to the cart.)  I'd also consider moving clamps there on a vertical basis, near one edge of the plywood slots...

 

I've been told it's similar to planning for a space trip.  You only have so much space, so nest as much as possible to get the most function.  You might also want to take a look at the Studley chest for more inspiration.  Every time I get stumped, I pull that out and start to marvel that he packed so much into such a small space.

Do you have any existing pictures of shop or future location ?

  • Author

Do you have any existing pictures of shop or future location ?

Nice, I like getting called out on this, LOL :blink::o:lol:

I will get some photos up thursday so you can see the disaster that I have on my hands at the moment. Warning, it will not be for the faint of heart...

  • Author

Ok, here is what the shop looks like... now as a preface I work full time, have two young boys and often work nearly full time on a second job doing remodeling. This past year to date I have done three kitchens and two bathrooms, despite working often out of a pig sty. I am going to change that as it is way more fun and easy to work where there is a home for each tool. Lot less time spent looking for something.

 

First pic is from outside the garage looking in, left side, next shot is the middle, next shot is the right hand side. The last side is where I started to build the cabinet wall. The tool storage low cabs with top can be partially seen.

 

IMG_20130919_133127_zps7b1fdf26.jpg

 

IMG_20130919_133134_zpsceb5f81a.jpg

 

IMG_20130919_133141_zps9a1eb361.jpg

 

IMG_20130919_133155_zps6048b8fa.jpg

  • Author

I am going to have to put the cleanup on hold for a little while.... I just got another remodel job on a small bathroom. As soon as I can finish that I will be full force in cleanup mode. A friend at the BORG signed me up with a commercial account. Got a 10% off coupon waiting for me.

Well, I see your first problem straight off.  You've got family stuff (like the bikes) in your shop!  Clean that right out, and there's no problems.!

 

You've got some unused space over the water softener: looks like a decent place to put those "occasionally used" items like that storage tub in the second shot, or shop lighting, or trash bags.  I'd definitely consider some square-ish storage for those injection-molded cases... or even getting rid of them completely to save some space.  The bikes: I'd consider hanging those from a hook (front tire is easiest), except they are ridden by those obviously not quite tall enough to reach the ceiling... which means either you put them away or you lower them via chain/cable/winch to use them.

 

I hate to suggest it, but you're probably going to have to thin out some of your flat scrap... A cabinet around/by the table saw will take care of some of that.. as well as provide an opportunity to 1: make a router table wing, 2: make an extension wing for wider materials, and 3: make storage space for some of those bench tools hidden in the center.

 

And something to store those ladders on will help greatly... either tucked into the flat cart or hanging from the ceiling.  (maybe behind the bikes?  Perpendicular to the lumber rack?)

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.