Chuck Melton Posted September 12, 2013 Report Posted September 12, 2013 I wanted to see if anyone has any tips or tricks for moving a fairly heavy table saw. The first TS I bought, I just disassembled and tossed in the back of my CRV, it was an old, heavy, but fairly small Delta contractor saw. The saw I think I am picking up in the next day or so is a much larger and heavier Grizzly hybrid. My inclination is to rent a low trailer with a ramp, secure it and move it with out taking it apart. I am going to be squaring the thing up after it moves anyway, but I'd like to avoid taking it apart entirely. Anyone have a better way to move a 400ish pound saw? Quote
dwacker Posted September 12, 2013 Report Posted September 12, 2013 Anyone have a better way to move a 400ish pound saw? Isn't that why we have children? 400 is not that bad a couple guys should have no problem getting it onto a trailer. Quote
ChetlovesMer Posted September 12, 2013 Report Posted September 12, 2013 My table saw goes 650 pounds. The first time I moved it, it took 2 of us and a hand-truck. Since then, I've moved it twice myself with just a hand-truck and a refrigerator strap. Unless you are going up and down stairs it really isn't that bad. Quote
pghmyn Posted September 12, 2013 Report Posted September 12, 2013 Isn't that why we have children? 400 is not that bad a couple guys should have no problem getting it onto a trailer. Get some of those moving straps that go on your forearms or over your shoulders. Shouldn't be too bad I'm assuming you are talking about the same saw that I have now. I got it into my basement with ease, with two people. I took off all the crating, and left the extension wings detached. Really was like carrying nothing over flat ground, but when it came to the stairs we took our time. Stair by stair we inched our way down. Didn't want a mishap where this thing landed on me. Once it was to the bottom, we were golden. Quote
sjeff70 Posted September 13, 2013 Report Posted September 13, 2013 Are we using hand-trucks or mover's straps with the extension wings still attached...trying to get it through a door... Quote
JoshC1501 Posted September 13, 2013 Report Posted September 13, 2013 When I went an picked up my Delta saw earlier this year it took 3 of us to move. It had a mobile base on it so we rolled it all the way to my truck. If you have a trailer that sits lower to the ground than a Truck, I would highly recommend it. It would have been pretty easy in that case. Quote
Trip Posted September 13, 2013 Report Posted September 13, 2013 You know, Marc has posted several videos of his shop moves -- the table saw figures highly -- worth a look... Quote
jHop Posted September 14, 2013 Report Posted September 14, 2013 I know he recommends an engine hoist for moving the saw around in the shop itself. Harbor Freight usually has one for under 200 that folds up (kinda) flat. (This, by the way, is one reason I don't have a table saw.) Quote
T-astragal Posted September 14, 2013 Report Posted September 14, 2013 Lower the blade and turn it upside down. They are top heavy and want to tip over anyway. Steve 1 Quote
Spencer_J Posted September 14, 2013 Report Posted September 14, 2013 Here is how I moved my unisaw. The loading dock helped get it in. But I'm sure I'd be able to get it back into my pickup by myself safely if there was no one left to help.. Taking the tailgate off was key!! Quote
Tom King Posted September 14, 2013 Report Posted September 14, 2013 I should have taken a picture a few weeks ago. I had a shop set up in a house I was finishing in my spare time. Someone came along that wanted to buy it if only they could use it for Labor Day weekend. We moved all the stuff about a half mile and set it up in a day. I used the tractor with loader for the big tools. The Unisaw, on a mobile base, wide right table with long Biesmeyer, Extractor dust arm, was moved in one piece. I always have a ramp into a house I'm building, so we wheeled the tablesaw down the ramp, with the saw end into the bucket. A strap was put around the saw with a big piece of foam rubber to keep it from getting scratched. It was a bit worrysome driving the tractor with the light end of the saw system sticking out the front, but it got there fine. Having two powerlifters for helpers is good too, but they didn't have to do any lifting. We rolled it right into its new spot, checked alignment, and it didn't move at all. That tractor is one of the best tools I've ever bought. http://www.historic-house-restoration.com/images/secondlogup.JPG In years past, we would roll the tablesaw close to a trailer, and turn it over onto plywood with the top down. Quote
..Kev Posted September 14, 2013 Report Posted September 14, 2013 My neighbor has that same tractor and I use it when I need to move the big stuff as well. It's amazing how many uses there are for a tractor! Quote
jHop Posted September 15, 2013 Report Posted September 15, 2013 Bucket? What about all that space on the roof?! Seriously, though, I hadn't considered a tractor before. Maybe because my mindset is more academic and broke right now than opportunities... Not too long ago, my dad and I helped my uncle load a small tractor into a truck for shipping to another state. We pulled out the come-along, tried to find the anchor points, and gave up. In the end, the three of us just grabbed corners and grunted. Of the three, only my dad does manual labor on a regular basis, and the most weights I lift is my backpack full of textbooks. It might have taken us a while, but never discount the value of elbow grease. and while the tractor we had to move was on the size of a small riding lawn mower, it was built before the Korean War, so it's still heavy metals. (Probably the same vintage as some of those Unisaws out there, and roughly the same weight.) It can be done. Less time worrying and more time doing, and you'll be fine. (Paralysis by analysis, anybody?) Quote
Chuck Melton Posted September 16, 2013 Author Report Posted September 16, 2013 Getting this thing moved was way easier than I anticipated. Renting the low trailer with the ramp was more than worth the $35. Two friends, two tension straps and a slow drive home made it mighty easy. I did cringe when my buddy tried to grab it by the fence rails, but there no damage done. Going to get the new-to-me Grizzly on a mobile base once UPS delivers it today and work on getting it tuned in. A quick test cut showed me it was a little out of square (1/32 off over 30 inches), but I was also ripping a cheap pine 2x4 while the saw was sitting on a furniture dolly, so it might not be that far off. I might splurge and get a Forrest WW2, which is almost as much as I payed for the entire saw. Quote
pghmyn Posted September 16, 2013 Report Posted September 16, 2013 1/32 over 30" isn't anything you can't clamp out Quote
woodieboy Posted September 16, 2013 Report Posted September 16, 2013 When I moved my band saw from basement to the shop, I removed the heavy parts like the wheels, table, motor and doors. Table saw is a simple machine to move, just disassemble it as much as possible. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.