bglenden Posted October 23, 2013 Report Posted October 23, 2013 I have decided to get a Domino, and have been convinced by the overwhelming opinion of commenters to swallow the Kool-aid and also get a Festool dust collector. As far as I can tell there is no difference in air volume between them, it's only a matter of how big the bag is and how big the unit is. I will not be moving it outside of my shop (aka garage), so in general I suppose bigger is better (fewer bag changes/empties), so long as the unit is not awkward to maneuver, which would imply that I should get the CT48. Does anyone have any comment on this, or on anything else that I'm overlooking? Cheers, Brian Quote
jmaichel Posted October 23, 2013 Report Posted October 23, 2013 They are bigger than you would think. I have the CT26 and think the size is just right for my shop. Bags are only $35 for a pack of five which is really not that bad. I thought about the 36 but could not see any justification for the extra size or cost. Quote
wdwerker Posted October 23, 2013 Report Posted October 23, 2013 I am happy with my CT22. I works with my Domino, sander and some job site clean up as well. It has plenty of suction for my router table and the drill press. I have a recurring order for a commercial client and have to drill 400 holes and it keeps up with the chips. Quote
Freddie Posted October 23, 2013 Report Posted October 23, 2013 All of them are same cfm's, just bigger bag capacity. I have the 26, and I will tell you it is absolutely more than fine as far as emptying goes .It is not as often as you think, unless you are using it all day everyday. I've emptied mine 6 or 7 times, and I still have the original bag it came with. I just squeeze the stuff out of the hole, and the bag still works. When I have the bag out, I check inside the vac, and no dust makes it into the vacuum, so I will keep using my original bag until it explodes! Quote
Pwalter5110 Posted October 23, 2013 Report Posted October 23, 2013 Now I don't have any festool but I see a lot of people with dust deputys sitting on top of their festool vac. I imagine that you would barely ever have to change the bag if you went with a set up like that... And PROBABLY a lot cheaper than upgrading to one of the bigger units. Quote
Trip Posted October 23, 2013 Report Posted October 23, 2013 ==> the CT48 The 48 is a beast... I think it would be too big for most common uses... I've got every-sized CT -- except the 48... For a CT that's going to capture lots of dust/chips -- like from a router, I attach the Oneida UDD.. Yea, it's a bunch of money, but it works so well and saves bags like crazy... I haven't changed the bag in either of my 26s in a year... http://www.oneida-air.com/inventoryD.asp?item_no=AXD000009 One note on the UDD -- if the separator fills-up and you don't notice (like heavy router-table use), the dust/chips flow directly to the vac (thus defeating the purpose of the separator). To overcome this, I took some fine "fish tank net" mesh and put it over the DD's vac-port... This prevents chips from going to the vac... I've had it in-place for several months and it works great... I sent a photo of my kluge to Oneida and I believe they are going to supply a more elegant version in future iterations of the UDD... I also incorporated a second 90 degree elbow in my setup -- after talking to Oneida, they are now shipping the UDD with 2 90degree elbows -- the hose routing is now more streamlined... The current-generation UDD doesn't attach solidly to a mini/midi without modding the base attachment flange of the UDD. Oneida is aware of this and they plan to change the base flanges (it may have already been done)... 1 Quote
Bobby Slack Posted October 23, 2013 Report Posted October 23, 2013 I would go with the smallest dust collector that allows you to use the reusable bag. Quote
pghmyn Posted October 23, 2013 Report Posted October 23, 2013 I have the CT midi, and it's perfect for me. I only really use it with a sander and occasional tracksaw use, though. Quote
bglenden Posted October 23, 2013 Author Report Posted October 23, 2013 Many thanks for all the comments/advice - it seems like smaller is better for once! Cheers, Brian Quote
Trip Posted October 23, 2013 Report Posted October 23, 2013 ==> it seems like smaller is better for once! I think the most useful sizes are the midi and 26... If you can, you should get to a woodcraft, et al to see the two side by side... Quote
Spencer_J Posted October 23, 2013 Report Posted October 23, 2013 One note on the UDD -- if the separator fills-up and you con't notice (like heavy router-table use), the dust/chips flow directly to the vac (thus defeating the purpose of the separator). To overcome this, I took some fine "fish tank net" mesh and put it over the DD's vac-port... This prevents chips from going to the vac... I've had it in-place for several months and it works great... I sent a photo of my kluge to Oneida and I believe they are going to supply a more elegant version in future versions... I also incorporated a second 90 degree elbow in my setup -- after talking to Oneida, they are now shipping the UDD with 2 90degree elbows -- the hose routing is now more streamlined... The current-generation UDD doesn't attach solidly to a mini/midi without modding the base attachment flange of the UDD. Oneida is aware of this and they plan to change the base flanges (it may have already been done)... genius.... thank you! Quote
Trip Posted October 23, 2013 Report Posted October 23, 2013 ==> genius.... thank you! Thanks... Necessity is the mother and all that... I was routing the dog holes on the Roubo build with a 2200 (which has excellent collection) and the UDD filled, the separator filled and the CT's bag filled.... So after changing the CT's bag (cursing all the way), I grabbed my fish tank net (handle and all) and just installed it right there and then to just get back to work... I made something a bit more elegant when time allowed... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.