TheFatBaron Posted October 25, 2013 Report Posted October 25, 2013 As my existing project backlog winds down, I'm thinking about a couple projects. As small task, I was thinking about making a rabbeting block plane, a la this Veritas plane. Now, I understand the reasoning for not making wooden bevel-up, low-engle plans. But I was looking at Hock Tools' shoulder plane and block planes and thinking "there's no real reason I couldn't combine the two." Right? Or am I missing something? Quote
ChrisG Posted October 25, 2013 Report Posted October 25, 2013 The problem is the because the sole is not continuous it may be difficult to make a plane that doesn't flex. I know this is a design challenge when making a metal rabbet block so I'm sure it would be with wood The Hock shoulder plane and wooden rabbet planes have tall bodies so there is a of material to keep the body stiff. That wouldn't be there with a low slung wooden block plane so the body seems likely to flex. Doesn't hurt to try though and see what happens. If nothing else you'll learn a lot. Quote
G S Haydon Posted October 25, 2013 Report Posted October 25, 2013 One thing metal planes do well is low angles and also allowing a rebate feature too. It might be cool to try a LA wooden plane but I think there aren't many of them for a reason (although I could be wrong) The above are wooden mitre planes. Quote
TheFatBaron Posted October 26, 2013 Author Report Posted October 26, 2013 I definitely wouldn't be attempting a low-angle plane. I think there's just not enough wood to support a blade. Essentially, I'm thinking about a shorter (length-wise) plane with a wider blade. Basically, something like the blade from this plane, set to 40° or so, bevel down, in a wooden body. Quote
derekcohen Posted October 26, 2013 Report Posted October 26, 2013 A wooden rabbet block plane is very doable since you are only removing wood from one side. This does not need to be much - just enough for the side of the blade to poke through. The weakness of wood is that it can flex when support is reduced. In particular, where a low cutting angle is required and one begins to consider a low bed and BU configuration (the LV has a 12 degree bed). Examples are the mitre planes that Graham shows above. The one in front looks like a Boxwood rendition by Bill Carter (fantastic plane maker!). I would instead take a leaf out of the book of a "strike block plane", where the configuration is BD, and the bed can be lowered to 38 - 40 degrees for the same low cutting angle of the LV (12 degree bed + 25 degree BU bevel). Here is one I built for a shooting board ... That's a solid body. There is a pictorial of the build on my website: http://www.inthewoodshop.com/ShopMadeTools/BuildingaStrikeBlockPlane.html Regards from Perth Derek Quote
Tom Crawford Posted October 26, 2013 Report Posted October 26, 2013 Derek, Congratulation on the photos and mention in the new issue of FWW Tools & Shops issue. Beautiful work! For those of you that have not seen it there is an old Spiers style infill smoother he restored and a Plow Plane he made to use some irons he had. Quote
G S Haydon Posted October 26, 2013 Report Posted October 26, 2013 Derek, that link and plane is my favorite so far, inspiring stuff indeed. Quote
TheFatBaron Posted October 26, 2013 Author Report Posted October 26, 2013 Derek - that plane is beautiful. Glad to know it's working out for you. I don't think I'll be making my first one out of a solid block, though... that's a bit above my skill level. Maybe for the next one I think I'll get the LN blade, though. Building the skew into the plane body in sketchup is making me nuts. I'll try leaving the blade flush on both sides, and if it flexes too much, I'll close off one of the sides. Quote
Tpt life Posted October 26, 2013 Report Posted October 26, 2013 I feel like I owe you money D. Most people charge to teach at such a detailed level. Many thanks. 1 Quote
TheFatBaron Posted January 1, 2014 Author Report Posted January 1, 2014 Well, I finally got a chance to work on this - and it works! The bed is at about a 35° angle (with an LN Block Rabbet blade ground to 25°). The body is eucalyptus (main body) and jatoba (sides), with walnut for the wedge. It takes some work to get everything set right, which is par for the course with wooden planes - hopefully this gets faster with practice. I find it absurdly easy to accidentally drop the blade through the bottom of the plane by tapping the wedge at the slightest of wrong angles (except, of course, once the plane is set and I'm actually trying to remove the wedge and blade). Fortunately, no major damage occurred when the blade hit the concrete floor in my basement. I didn't really spend -that- much time fiddling, but was able to get decent cuts with and across the grain, and a not-too-bad cut on end grain on a piece of soft maple. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.