Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Faking it

Featured Replies

So I just picked up a job building some custom oak end tables. Client knows what she wants, had pictures, dimensions, no problem.. Then she asked me if I could build her a toilet topper, and wants it to match her existing vanity, this is a problem... As you can see in the picture, the door is just a slab of particle core (Ikea?) with v-grooves to resemble a frame and panel style door. I've never constructed doors like this and am wondering if you fine folks have any good ideas, or have ever run up against it before? I'm going to try some experiments this weekend v-grooving some oak particle core ( sorry router bits), perhaps try veneered ply as well.

Any thoughts on how this should come together? I'm thinking maybe mask out the v-groove and fill it with something that will take a stain?

post-7010-0-96133400-1383183151_thumb.jp

You could always build a new door for the vanity as well.

 

I haven't had to deal with something like that before but it sounds like you've got it pretty well reasoned out.  A darker pigment of some sort in the groove would make it look like a permanent shadow.

  • Popular Post

look at the cross grain piece at the top. i would just build a shaker style solid oak door, or use 1/4 ply for the panel. you can add the tiny vee groove if needed.

  • Author

Good point. She does want that flat look though, maybe I could use some wide veneer tape in between the grooves to simulate the rail? Do you think the particle core would be stable enough to go frame and panel, flush the panel to the front and v-groove it, essentially locking it in?

  • Popular Post

Make sure you put the pull on crooked, so it matches the vanity too. :rolleyes:

  • 2 weeks later...
  • Author
  • Popular Post

Well here is my best run at a cheap crappy door.... Now to just get the finish on and get the pulls mounted crooked...

post-7010-0-44876700-1384120767_thumb.jp

Well here is my best run at a cheap crappy door.... 

 

You do 'cheap and crappy' really well.  :D

 

Seriously, nice job. What was your final technique?

Looks great to me! I would also like to know what you did. I am frequently called on to reproduce a door for existing cabinets. Appliances change or a door gets destroyed and the client doesn't want to replace all the doors.

  • Author

Thanks guys. I ended up going with some pretty good quality oak veneer ply, not many voids or knots in the inside layers. I v-grooved out the stiles and rails and then put some wide edge banding on the rails just up to the start of the groove. It makes them slightly thicker, but not very noticeable at all. I didn't end up using anything to fill the grooves. Client wants a pretty dark Java-red finish which set the lines off nicely. I'll try to post a pic after I spray it next weekend.

  • 2 weeks later...
  • 2 weeks later...

Great job. I'll remember that the next time I run into something like that. Thanks.

Great work on that cabinet

I'd say the original door was made from a single sheet of veneered particle board.

All the components were cut.

1 centre Panel, 2 stiles and 2 rails. And then everything was assembled around the centre panel with biscuits or dowels or something similar and that V groove was added not just for decoration but to hide all the joints and glue lines.

This allows all the pieces to be the same thickness and have the grain running in the right direction and best of all to the untrained eye it looks like a frame and panel door !!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.