Doomwolf Posted November 11, 2013 Report Posted November 11, 2013 If you've read any of my posts in the general forum you'll know that for my first woodworking project I'm making a coffee table. I'm doing it in the Mission-style because I like the solid, simple lines it has while being completely functional. Assembly has already begun, so this journal will have a little bit of time lag with reality. I started with going through my Dad's barn - we took an ash tree down years ago, and my Dad took it to the local sawmill and turned into lumber. There are some nice pieces in there, my legs are cut from a slab that was originally 5 1/2" by 2 1/2" and 5' long, and it wasn't the largest piece in the pile. The original plan was to make the table during an 8-week woodworking class that I signed up for via the public school board. The instructor is a bit paranoid about safety (told someone that it was "too dangerous" to let them use a thickness planner, even though they have one at home) and the expectation was that we would use pre-dimensioned lumber (something not stated in the course description), so I spent Thanksgiving in my grandfather's basement learning how to make everything square. 1 Quote
Doomwolf Posted November 11, 2013 Author Report Posted November 11, 2013 After getting the lumber square I was hoping to make some cuts in class, but when the instructor insists on supervising your first cut of the night on everything (including the bandsaw) you spend a lot of time waiting around not doing much, so after a couple of weeks I went back to granddad's and spent the afternoon cutting and assembling. My first major lesson from this project is, if you are going to join everything with dowels, and you are using a home-made jig to drill the holes, make sure the jig is accurate before you drill the holes in everything. I was using a cordless drill with generic twist bits, and hadn't clued into the idea of making a starter hole with a punch when I drilled my first set of holes, so they weren't in a straight up-and-down line with each other. So I made a jig that reflected that, drilled a bunch of holes, realized that I flipped it the wrong way every.single.time. and had to spend an additional 1.5hrs fixing my mistakes, either by boring new holes, or widening existing ones to get the dowels to line up. Some lessons taken very much to heart out of this process, I just hope it does not compromise the structural integrity of the piece. With all that said, here are some pics: Quote
..Kev Posted November 11, 2013 Report Posted November 11, 2013 Great advice on the dowels! Thanks for the update, it's looking great! Quote
Doomwolf Posted November 15, 2013 Author Report Posted November 15, 2013 I spent this past Saturday in my grandfather's shop again, making the second side assembly. It was basically the same process as the last one, but with the experience gained & some relative dimensioning, I feel that I produced a better product this time around. I did still have some trouble lining up holes, but it was a lot less of a problem - chisel away one side of one hole in a piece and everything fit together. I drill pressed the dowel holes - no issues putting them in the legs, but they weren't necessarily always straight in the end pieces. Any advice on how I can dowel the 42" stretchers when I move onto the next step? In the end, I started a 1300 & cleaned up by 1930, so subtract a tea break with Oma and it took 6 hours from cutting to dry assembly. The friction fit was good enough that I could hold it sideways and nothing would fall out. I glued it up the next morning and kept the clamps on until lunch on Monday. Quote
Beechwood Chip Posted November 15, 2013 Report Posted November 15, 2013 Nice job! For the 42" stretchers, I'd make a jig from a bit of 2x4 with a groove that fits the stretcher, a hole to position the dowel, and a centerline. Slide the jig until the centerline matches your lay out mark on the stretcher, clamp, then use a hand drill. Quote
Doomwolf Posted November 20, 2013 Author Report Posted November 20, 2013 Bit of a late update, but last Wednesday I got some more work done. The shop where the woodworking class is has an orbital spindle sander, so I used that to smooth out the curve in the stretcher, and then got to work making a template for the 42" stretchers. I ended up making one and a half templates - cut half a curve, copy it onto an identical piece of plywood, cut the curve, transfer it to the first template and cut again. I'm happy with the results. Aprons and stretchers are cut to size, so the next step will be to cut the stretcher curves, then start drilling for the dowel pegs. If all goes well, I will be able to get the curves cut tomorrow and then spindle-sand them. My grandfather doesn't have one, and tomorrow night is the last class, so here's hoping. That would also allow me to drill & glue the frame Saturday, and while the glue is drying I can see about putting the shelf together, and possibly install it Sunday. Then all that would be left would be the table top, followed by some sanding and finishing. My grandfather suggested boiled linseed oil - does anyone have an opinion as to how it would look on white ash? Beechwood, for the jig you're suggesting, would I be sliding the jig DOWN the end of the piece, or ACROSS (left-right)? I don't have a hand drill, but I presume a cordless would work just as well provided I'm careful. Quote
wdwerker Posted November 20, 2013 Report Posted November 20, 2013 Slide the jig across the piece that needs a row of holes. A cordless drill is a hand drill, as opposed to a drill press which is a stationary tool. I once took a night class in wood shop at the local high school just to get access to the bigger machines. Teacher realized I didn't need to be watched so he just asked me to help others while I waited for my turn on the big tools. I learned a few things in that class and here it is 20 years later and I am still learning . Treasure your time in your grandfathers shop, those are some of my fondest memories. 2 Quote
Doomwolf Posted November 21, 2013 Author Report Posted November 21, 2013 Real-time update! We had the last woodworking class tonight. On the one hand I can't say I will miss out instructor, but on the other hand I will miss having access to an orbital spindle sander. I was able to get the curves cut in the stretchers (before and after pics below). First cut wasn't the best, took a few passes and overall quality of the cut was patchy. Second one I roared through like it was nothing and took off all the material in one pass. A couple of little waves in it. but I'm still learning. I taped the two pieces to a flat piece of scrap and sanded them together so the curves are pretty much identical at this point. Only catch is I still have some pencil marks and scribe lines showing, so I'm going to have to do a bit of hand sanding to make things look nicer. That said, the side assemblies are covered in pencil marks, so sanding is a given, unless someone can recommend a better method. I got a jig started for drilling the dowel holes, so hopefully I can power through that step quickly* on Saturday and glue up the frame. *I'm starting to notice that in woodworking "quickly" seems to be defined as "less than four hours" And, as promised, before & after pics. Quote
Byrdie Posted November 21, 2013 Report Posted November 21, 2013 I apologize if it seems I'm being picky but I just have to check because I'm getting confused - When you say "orbital spindle sander" do you mean "oscillating spindle sander" (the post or spindle on which the sanding drum is placed goes up and down) or is there another variety of the tool I'm not familiar with? Quote
wdwerker Posted November 21, 2013 Report Posted November 21, 2013 You can buy a small bench top spindle sander at Home Depot. I use one in my shop. It has oscillating belt sander and can switch to just a drum sander if you need to work on a smaller diameter piece. I think it was around $200. Quote
Doomwolf Posted November 21, 2013 Author Report Posted November 21, 2013 Sorry, I meant oscillating spindle sander, my bad. Home Depot sells one for $169 CDN apparently, which I could certainly afford, but when you live in an apartment the issue is more where to put it, to say nothing of dust collection. I suppose I could buy one and then give it to Gradndad on permanent loan, but he doesn't have much space to spare either. http://www.homedepot.ca/product/oscillating-spindle-sander/853115 Quote
wdwerker Posted November 22, 2013 Report Posted November 22, 2013 I bet Grandad could find uses and room for it. I passed down my first tablesaw to my Grandad when the bearings wore out on his. He was like a kid with a new toy and I was glad to be able to payback all the time he spent teaching me. That Ridgid sander does make a mess but if you hook a shop vac to the port in the back is isn't too bad. Quote
..Kev Posted November 22, 2013 Report Posted November 22, 2013 I use one from Grizzly in my shop quite often. Just a bench top model that was $140.00 but, I was quite surprised at how well the dust collection was when hooked up to the vacuum. I've had it for a few years now, it gets light use. Still kicking tho! Quote
Llama Posted November 23, 2013 Report Posted November 23, 2013 I have the Ridgid spindle/belt sander, and I love it. I use it all the time, and I never have a problem with dust. My dust collection setup consists of a shopvac, and a Rockler cyclone (the blue one). I buy the replacement abrasives from Amazon, at a good deal too plus free shipping. Can't beat that! I think the Ridgid model is around $200, but has the distinct advantage of also being a belt sander. Very easy tool-less change over. Oh, and pick up one of those eraser looking things to clean your abrasives on these things, no matter which one you get. Works like a charm! Quote
Doomwolf Posted November 24, 2013 Author Report Posted November 24, 2013 Spent another Saturday afternoon in Granddad's shop. With the sides made, and the aprons and stretchers cut, it was time to start drilling dowel holes. Took a good six hours, but it is now sitting there with the glue and clamps on, so I'm happy. Found that making an X with a mortising chisel is another good way to make a starter hole for the drill. All that is left to do now is make the shelf and the table top. Table top I plan to put on using the figure eight-style fasteners from Lee Valley. The shelf might be done the same way, or I may use glue and/or cleats. I'll probably just figure it out as I go along. Quote
Llama Posted November 24, 2013 Report Posted November 24, 2013 The figure 8 clips from LV are great.This is looking nice! I plan on making mission piece soon. I hope it turns out as nice as yours! Quote
..Kev Posted November 24, 2013 Report Posted November 24, 2013 Looking good Doom! Not sure about where you live but, I've found the figure eight-style fasteners locally way cheaper than LV. Either way, it looks like you're nearing the finish line on this one! Congrats! 1 Quote
Doomwolf Posted November 25, 2013 Author Report Posted November 25, 2013 TIODS - What store/company are they from? I'm in Canada, and blessed with having a Lee Valley in town, but I wouldn't complain if I could get them future for another project. As it is, I bought two packs because a) too many is better than too few & I'm thinking of making a set of matching end tables over Christmas. Mel Morris - Thank you for the compliment! I will refrain from listing all the places it isn't 100% square to preserve my illusion of competence. 2 Quote
..Kev Posted November 25, 2013 Report Posted November 25, 2013 Last ones I bought locally were from True Value or Ace Hardware, I forget which. I guess my point was to have a look locally and save the shipping on this kind of stuff. I keep a dozen or so on hand and just add it to my resupply list when I'm going that way. I live about 6 miles from the Canadian border (West coast), maybe I'll have to make a trip up there to see what's available to my friends up North. Quote
G S Haydon Posted November 25, 2013 Report Posted November 25, 2013 Spent another Saturday afternoon in Granddad's shop. With the sides made, and the aprons and stretchers cut, it was time to start drilling dowel holes. Took a good six hours, but it is now sitting there with the glue and clamps on, so I'm happy. Found that making an X with a mortising chisel is another good way to make a starter hole for the drill. All that is left to do now is make the shelf and the table top. Table top I plan to put on using the figure eight-style fasteners from Lee Valley. The shelf might be done the same way, or I may use glue and/or cleats. I'll probably just figure it out as I go along. Doomwolf, you have made great progress so far, this is a very very good first attempt. I have some tool envy too. Marples Splitproof Mortice Chisel! I had a set of Splitproof bevel edge when I started work, I used the same "mallet" as you (and still do a lot of the time). Gotta love those claw hammers Quote
Doomwolf Posted November 26, 2013 Author Report Posted November 26, 2013 The chisel is his, not mine, but very much appreciated. I'll have to tell him he has good taste though. I'm thinking of getting a set of Narex mortise chisels after Christmas (I already have a set their bevel edges on my Christmas list). The hammer I got as part of a tool set for Christmas ten or so years ago. It hasn't really been used before, but it's the perfect weight for this craft, great at taping things. Question for the forum - once I have the shelf and table top on, should I chamfer the edges or leave them square? What looks/feels better in your experience? Quote
Doomwolf Posted December 2, 2013 Author Report Posted December 2, 2013 IT'S ALMOST DONE! All I have left to do is screw the table top to the frame.* Pics and details should go up sometime tomorrow evening. *and then finish the damn thing. I suppose I should probably do some research before willy-nilly applying stuff. Quote
Doomwolf Posted December 2, 2013 Author Report Posted December 2, 2013 I spent most of Saturday in Granddad's basement. For helping the first time he was actually involved helping me with the project - we spent a couple hours getting the tabletop glued up. I moved a little too slow, and didn't notice one board was really bowing up until it was too late to force it back down, but otherwise it went fine. While the top was drying we went and used a stop block on the radial arm saw to create nine slats to make up the bottom shelf. To hold everything on, we glued & pin-nailed pre-made pin mouldings to the stretchers, and thrn glued/pin nailed the slats down. 18 clamps later we left everything to dry for the night; one truly cannot have enough clamps, or enough of any kind of clamp. Somewhere in there I used a chamfer plane that he had to round off the table legs. The first pass went fine, but most of the rest had some amount of tearout. I'm not sure how much of that to chalk up to bull blades, operator error, and the wood itself. Sunday we spent 45 min in the garage with me holding the table while Granddad belt-sanded the crap out of it to make everything level. Unfortunately the highest belt grit that Home Hardware has was 120, so the 220 application is going to have to be done by hand at some point in the future (oh joy, oh bliss). With the table top flat, it was a little matter of doing some touch-up sanding, rounding over edges, etc, and then attaching the hardware for when I go to attach the table top (I didn't assemble it fully because Hyundai Accents are not designed for furniture). I'm kind of really happy about the whole thing. On an unrelated note, the family celebrated my birthday on Saturday. My parents gave me a set of seven Narex bevel-edged chisels, and a tool roll to hold them. I'm quite pleased. I know it isn't finished yet, but what do people think? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.