Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

20 amp breakers..

Featured Replies

I have a 100 amp service in my shop. all 20 amp breakers except for 1 15 amp that services the exterior lights. On one breaker I have added 5 two bulb t8 fixtures and a 54" ceiling fan. This breaker is also connected to a few outlets. I am concerned I won't be able to use a large machine on these outlets if I have the lights on. I have calculated roughly 4-5 amps total for the lights and fan. I am thinking of smaller machines, sanders, 14" bandsaw, drill press... could it handle a jointer or planer on the same breaker?

Oh and another question, I currently only have 110 tools... I would like to have an electrician or myself run conduit on the walls and install 220 around the shop... I believe I have a few more spots on the breaker... how many do I need for 220 and how difficult is it to install? do you recommend doing it myself after a bunch of research and video or just hire an electrician? I have wired 110 throughout the shop and am pretty comfortable with that... just not sure how to connect to the breaker panel.

220 is not that scary if you understand the basics. If you are uncomfortable with it I would have an electrician help you get started and after you have an understanding you could finish it off. Around here most jobber type electricians would be more than glad to work with you.

Not sure if you do, but you should have your lights on their own circuit, even separate from the fan.

 

220 isn't hard to run. But if you aren't confident, hire someone. Don't mess with electricity. 

+1 lights on a separate circuit, especially in a shop.  Any tool can pop a breaker if something goes wrong, and you don't want to be in your shop, in the dark, holding a power tool.

 

BTW, I have these plugged in around my shop.  They turn on automatically if the power goes out, or when you pull them off the wall.

Just to expand on my previous post...

 

In my shop, each wall is on it's own circuit. And I very rarely have two things going at once. My lights have their own circuit, and so does the outlet on the outside of my shop/garage. Most of my outlets are 2 feet of the ground with the exception of my TS plug, and my shop vac plug. At the time I thought it would be a good idea to make those lower. I also have a couple that are about 4 feet high for chargers and bench things.

 

There was a very good article in FWW on electrical layout a few years back. 

 

I like those lights Beechwood! Very cool, I'll have to get some of those. 

Not to be a jerk but with electricity I think if you're asking these questions you should hire an electrician. Also think about getting the amperage up to 30amp outlets. I doubt you will be happy with 20amp 220v tools for all that long. 

I agree with PB - get 30 amp breakers/outlets for your 110v outlets if your wiring will support it.

 

Second, if you can wire 110v, you can wire 220v. It's just a pain in the ass. Just - check your local building codes, even call your local inspectors - and get your inspections done. My town's (electrical) inspectors were incredibly helpful with clarifying some details from the codes, and even offered suggestions that would improve our wiring.

If your panel is close to being full they make thin breakers where you can put 2 of them into one regular slot. Unless you have several people working at the same time all of your tools won't be running at the same time.

I have done my own wiring in the past. I always try to meet or exceed code. The minimum wire I use is 12 gauge where 14 is allowed.

Follow grounding requirements exactly. Work neatly. An electrician taught me to straighten my wires and bend neat corners so it is easy to follow where a wire comes into a panel and which breaker it goes to.

Think of 220/240 as 2 circuts in one box, 2 hot legs, 1 neutral and one ground in most cases.

I have known electricians that will let you do most of the work mounting boxes and then they will check it over and do the final hook ups.

==> I am concerned I won't be able to use a large machine on these outlets if I have the lights on. I have calculated roughly 4-5 amps total for the lights and fan. I am thinking of smaller machines, sanders, 14" bandsaw, drill press... could it handle a jointer or planer on the same breaker?

 

You need a plan and you should hire a pro...

 

Step one: write-out all the tools/services you have now and intend to run in your shop over the next few years... Get the volt/amp specs from the internet for your planed purchases...

 

Step two: hire a pro, and walk him/her through your requirements... 

 

Sure, a pro costs money, but it beats a fire...

 

The good news is that a 100a service should have no issues powering your shop... So you're not going to incur large $$.

 

One question that pops up -- where are all the breakers going now? A standard 100a panel has 20 breaker lugs... That's usually enough for any hobby shop... Unless I missing something...

I agree with all the above, 220 is easy to run, use 30 amp 220 outlets, lights should be on their own cirucit as well as any built in appliance. When in doubt run another circuit, there are thin and there are double breakers to "expand" the abilities of your pannel. If in doubt, get help at least until you understand what you are doing, get a permet and have it inspected, it is money well spent in the end, some fire insurance policies are void if there are unpermeted circuits run.

 

I have TWO pannels in my shop, All my runs are minimum 20 amps, all wire is minimum 1 size larger than code. The most outlets I have on a single 20 amp line is 3 (double outlet boxes, total of 6 recepticals)  though you can have up to 11 (depending on your code). Any electrical job worth doing is worth overdoing.

For perspective, my entire garage shop is one circuit on a 20 amp breaker. Lights are seperate. As a one-man hobby workshop, I have never found a need to run more than one tool plus a DC or shop vac at the same time. Haven't tripped that breaker yet...

I can respect that. I am a one man shop too but I do have a few tools that are too big to move and require their own feed, such as my arc/tig welding machine which requires a 100 amp 220v line, or the mill or lathes and it goes on, I have tools that are 3 phase and single phase and a shop that is 2,250 square feet, (30' x 75') and 20 feet tall. it is nice to have the room but like all things, it comes at a cost. Part of the cost is providing proper electrical service.

 

I know I am by a very far ways, the exception and that I have been blessed with a wife who supports me and a property that is big enough to allow the shop. I have over 35 years of collecting "great deals" on equipment. There is no way I could buy any of this stuff at even used retail price, it all came from auctions, millitary surplus Craigs list, and years and years of poking in dirty, grimey back rooms etc.

  • 2 weeks later...

I just got my 16 x 16 shop completed back in Oct 2013.  What I am finding out is what I already knew.  Wiring lights on 1 breaker.  wiring electrical plugs on another breaker.   Your heavier duty electrical consumption needs it's own wiring breaker.  I do custom acrylic fabrication for a living.  My table saw, shop vacuum and my commercial 4 bar 48x48" strip heater are going to draw a lot of power.  I rarely will have all 3 running at the same time.  This all needs to be separate then all the plug in stuff in my shop.  I have a router, radio, heater and a lamp that I can run on one breaker 20Amp.  Separate breakers for everything grouped such as lights on one breaker, heavy power use equipment on it's own breaker, and light duty stuff such as radio drill press lamps and drills/chargers on another.  The thing is you don't want to trip breakers, so having separate breakers will allow you full use with out the failure of the breaker. 

Get a pro to come in and do a consultation for you and get quotes/recommendations.   You probably can do this for free until you have them come back and do the wiring.  Wiring was about $500 for a 100Amp subpanel when I had mine done.  I dug the trench.  I wired my shop myself this go around.

  • 2 weeks later...

Keep in mind that you may want to move some day. DIY electrical circuits can cause you a lot of grief when a buyer wants the house inspected. A licensed electrician is a good idea, and depending on local building codes, a permit and inspection may be required as well.

 

I'm curious... if the wiring is done well and to code, how is a home inspector going to know if they are DIY or not, unless they pull permit records?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.